GN 9050 Beta User Manual GN 9050 WIRELESS HEADSET SYSTEM BETA USER MANUAL 1
GN 9050 Beta User Manual Component list 1. 2. 3. 4. 5. Base station Base stand Remote Interface cord AC adapter 6. Battery 3 4 6 1 2 5 Remote Beltpack Functions 1. Headset Mode indicator-blinks when the system is in Headset mode, no light when in handset mode. 1. Volume control- press + to increase volume and – to decrease volume 2. Mute button: Press to activate mute and press again to unmute. 3.
GN 9050 Beta User Manual Battery Information Battery Type Capacity on-line Capacity off-line Recharging Time Battery Life Nickel Metal Hydride (NiMH) 3.6 V 500 mAH Fully charged battery provides 6 hours of talk time Fully charged battery provides 80 hours Maximum of 3 hours 2 years if battery is recharged when not in use Basic Feature Set: • 2.4GHz, Digital FH-SST radio system • Up to 150 feet range from base station • Minimum of 50 concurrent users in one location w/ encryption/ security.
GN 9050 Beta User Manual BASE FRONT Spare battery charge indicator In-Use Indicator Remote charge indicator Where Remote docks to charge 4
GN 9050 Beta User Manual BASE REAR In-Use Indicator Spare battery charge indicator Contacts for Spare battery slot Host Port Spare battery slot Base Stand AC Power Jack To Handset AUX Jack (underneath plastic form) 5 To Phone RJ-9
GN 9050 Beta User Manual The base unit contains the following Indicators/Buttons/Switches/Controls: • Status Indicator: This indicates Base unit link status. The LED will be constant when a link is established and while in headset mode. • Remote unit Charge Indicator: This is a red/green LED that indicates red when charging and green when fully charged. • Spare Battery Charge Indicator: This is a red/green LED that indicates red when charging and green when fully charged.
GN 9050 Beta User Manual BELT UNIT, FRONT Clip (behind) In-Use Indicator On/Off Button Volume Up Button Headset 2.5mm plug Volume Down Button Removable Battery Pack (behind) Mute Button BELT UNIT, REAR Clip contacts (inside TBC) Belt Unit (behind) Clip Removable Battery Pack 7 Headset 2.
GN 9050 Beta User Manual The Remote unit contains the following Indicators/Buttons/Switches/Controls: • ““ON/OFF/Handset Lifter” Button: This button attempts to initiate a voice link or terminates a link depending on the current link state as well as serves as the handset lifter control button that raises and lower the handset on the telephone when using it with the optional GNN handset lifter or Hello Direct ReadiLine.
GN 9050 Beta User Manual Setting Up 1. Connect all Cords. Unplug the handset cord from the base of the telephone. Plug the Interface cord into the vacated handset cord port on the telephone. The location of this port is different for each phone and is often on the underside of the phone. Some telephones must be programmed for headset use. 2. Attach the Base Stand. Carefully insert the three plastic clips into the vacant base station holes. 3.
GN 9050 Beta User Manual 4. Connect the Headset to the Remote. 5. Charge the Remote Slide the Remote into the Charger on either side of the base station. The Battery Charge light on the front of the base station illuminates. Charge the battery for a full three hours. You may use the handset while the battery charges. Note: Battery Charge Indicator blinks green when battery is fully charged.
GN 9050 Beta User Manual 6. Using the Headset Press the On/Off Headset Handset button to put the system in headset mode. The headset mode light on the top of the remote blinks and the In Use indicator on the base station illuminates. 7. Put the headset on and select a telephone compatibility setting until dial tone is clear. If dial tone is clear for both A and G set to A. 8. Remove the handset and make a call.
GN 9050 Beta User Manual Cautionary Notes to Computer Users: When using any headset with a computer, care should be taken in dry or low humidity environments to protect the user from electrostatic discharge from the monitor (CRT). Computer monitors can induce a substantial electrostatic charge when turned on or off, or when there is a power failure, and the resulting electrostatic discharge can be passed through the headset to ground.
GN 9050 Beta User Manual EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 1. This equipment is compliant with Part 68 of the FCC Rules. On the Base station of the equipment, is a label that contains, among other information, the FCC registration number for this equipment. If requested, this information must be provided to the Telephone Company. 2. The device may not be connected directly to the telephone network, but must connect to a FCC registered telephone. 3.
GN 9050 Beta User Manual Industry Canada Notice to Users: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirement as prescribed in the appropriate Terminal Equipment Technical Resource Document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.
GN 9050 Beta User Manual Warranty: GN Netcom, Inc. warrants this product against all defects in material and workmanship for a period of two years from the date of original purchase. The conditions of this warranty and our responsibilities under this warranty are as follows: • The warranty is limited to the original purchaser.
GN 9050 Beta User Manual To Obtain Service: For customer service and technical support, call GN Netcom, Inc. at 1-800-826-4656 or 1-603-598-1100. Ship the product in a suitable shipping container, fully insured and with the shipping charges prepaid. Include the following with the product: • Your name, company name, address and telephone number. • A description of the problem.