Instruction Manual

Introduction
Setting your thermometer
Function
How to measure temple temperature
How to measure object temperature
Display LCD
Data Transfer via Bluetooth
Non-contact temple thermometer uses an infrared detector to detect
body temperature from the temple for adult and child in the hospital,
home or public place. This thermometer could also detect object tem-
perature.
Please read the instruction manual carefully before using the prod-
uct and be sure to keep this manual.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful in-
terference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
1. Open the battery cover.
2. Press “ON/OFF/Memory” button to power on the device.
3. Enter the setting mode by pressing the “
” button to switch Temple/
Object temperature, Celsius /Fahrenheit scale, and adjust Bluetooth and
beep sound in order.
4. Change the measuring target between the temple and object by pressing
the “ ” button. After setting a new measuring target, the measuring site
icon on the display will also be switched accordingly.
5. Change the °C and °F by pressing the “ ” button again to enter the set-
ting mode. Press the “ ” button to switch the corresponding measuring
scale. The measuring site icon on the display will also be switched accord-
ingly after a new measuring scale is set.
6. After adjusting measuring target and scale, press the “ ” button again to
move to the next setting of Bluetooth and beep sound.
Temple
Temperature
The thermometer has been designed for practical use. It’s not
meant to replace a visit to the doctor. Please also remember
to compare the measurement result to your regular body
temperature.
Object Mode
The object mode shows the actual, unadjusted surface
temperatures, which is different from the body temperature. It
can help you to measure any object other than body surface,
for example the baby’s milk.
Fever Alarm
If thermometer detects a body temperature ≥37.5°C (99.5°F)
there will be four beeps sound with flashing reading to warn
the user for potential fever.
1. Always make sure the probe is clean, and without damage.
2. Press “ON/OFF/Memory” button to turn on the device.
3. Make sure the measuring site icon is shown on the display before
taking measurement.
4. Vertically aim the thermometer at the temple with a distance of less than
10 cm. If the temple is covered with hair, sweat or dirt, remove the obstacle
from the temple to improve the measuring accuracy.
5. Press the “Measuring Trigger” button to take temperature. Measurement is
complete when you hear a long beep sound.
1. Press “ON/OFF/Memory” button to turn on the device.
2. Make sure the measuring site icon
is shown on the display before
taking measurement.
3. Once aiming at the measured target, press the “Measuring Trigger”
button to take temperature. Measurement is complete when you hear
a long beep sound.
4. Read the recorded temperature from the LCD display.
5. If Bluetooth has been activated, the data is automatically transferred to
the App after successful completion of the binding process, please see
Data Transfer via Bluetooth.
Note:
1. Applications include temperature measurements for Water, Milk, Cloth,
Skin or other object.
2. This mode shows the actual, unadjusted object temperatures, which is
dierent from the body temperature.
Pairing the device with your Smartphone
1. Download and install the applicable APP onto your smartphone.
2. To bind this device with your smartphone, turn on the device, Bluetooth
and the App of smartphone, and follow set-up and binding instructions.
3. The Bluetooth symbol (
) will ash on the display that indicates the
binding is proceeding.
- If the binding is successful, the Bluetooth symbol ( ) will illuminate on
the display and the current measured temperature will automatically
be transferred to the App.
- If the binding has failed, the Bluetooth symbol ( ) will keep ashing
until the device shuts o automatically after 1 minute, and the cur-
rent measured temperature will not automatically be transferred to the
App. Please rebind this device with your smartphone.
Notes:
1. Unbinding your device will not delete the data from the App.
2. If you rebind your smartphone with the device, all prior reading history
stored on the phone App will be retained.
3. Bluetooth data transfer will reduce the battery capacity.
4. Electromagnetic interference: The device contains sensitive electronic
components. Avoid strong electrical or electromagnetic elds in the di-
rect vicinity of the device (e.g. mobile telephones, microwave ovens).
These may lead to temporary impairment of measurement accuracy.
Non-Contact Telephoto
Thermometer
Model:
HC700 BT
Warning: Changes or modications to this unit not expressly approved by
the party responsible for compliance could void the user authority to oper-
ate the equipment.
CAUTION: This Transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
7. Adjust Bluetooth and beep sound as described above, using the “
” but-
ton to choose whether automatic Bluetooth data transfer and beep sound
is activated (Bluetooth symbol ( )+ , / or deactivated (Bluetooth
symbol ( )+ , / ).
8. Your thermometer is ready for measurement after all symbols appear or
pressing ON/OFF/Memory button again.
Note:
• The initial setting is Temple temperature mode, Celsius scale, Bluetooth and
beep sound activated as default.
6. Read the recorded temperature from the LCD display.
7. If Bluetooth has been activated, the data is automatically transferred to
the App after successful completion of the binding process, please see
Data Transfer via Bluetooth.
Memory function
There are total 9 set memories for measurement records. If the reading of
the thermometers is within the normal temperature range of 34 °C to 42.2
°C (93.2 °F to 108°F ), when the measurement is done, the measurement
data is saved into memory.
• Press “ON/OFF/Memory” button to repeatedly recall each temperature
memory.
1
2
3
4
5
6
7
1. Probe
2. Measuring Trigger
3. Strap
4. Backlight LCD Display
5. ON/OFF/Memory Button
6. Selecting Zone
7. Battery Cover
Selecting Zone
APP
36.8°C
APP
36.8°C
1. The temple temperature
measurement mode
2. The object temperature
measurement mode
3. Battery
4. Bluetooth Mark
5. °C/°F scale
6. Temperature display
1 2 3 4 5
6
10cm
3.94
GMC_IB_HC700BT_EN_AH_ver2104.indd 1 2021/1/19 下午 12:09:08