User Manual

1 2 3
6 8
1、
7
Introduction
2.5inchHDDDockingStation
GLOTRENDS
www.glotrends-store.com
It`s a high performance 4 Bay docking station with USB 3.0 and eSATA
interface as well as 1:3 clone function.
Step II: Partition and Format
b) Right click the “Disk 1”, then click “New Simple Volume”.
c) According to the instruction, input the size of partition, then click
“Next”to finish.
d) You will find your new hard drive in your PC, it is ready.
[e-mail]
4 Bay Docking Station
USB 3.0 & eSATA & 1:3 Clone Function
a) View “computure”-“Manage”-“Disk Management”to find
your drive.
*MBR or GPT mode to be selected during this produre, hard drive less that
2TB, select MBR; more than 2TB, select GPT.
*Windows XP system can not support hard drive more than 2TB. You
need to upgrade your OS at least Win 7 to use hard drive more than 2TB.
Specification
1) USB 3.0(5Gb/s) and eSATA(3Gb/s) output
2) Support 4 bay 2.5/3.5 inch SATA I/II/III HDD&SSD
3) 1:3 Clone Function
4) Power Switch and LED indicator
5) Compatible with Windows/Mac
Clone Function
1) Moving the function switch to “Clone”mode
2) Connecting docking station to power source with power cable
3) Inserting hard disk into docking station
4) Pressing “ON/OFF”button and wait. Disk indicator will light up,
when you find disk in your PC
5) Pressing “Clone”button 2 times, and then buzzer “BB,BB,BB”,
hard disk begin cloning
6) Cloning process LED indicator will light up from 20% to 100%
7) 5 LED indicator will light up and sound prompts for completion
Attention:
a) Target disk B/C/D >= source disk A
b) Once clone begin, target disk will be formatted. Please back up your
data first.
c) It will take time during cloning, please be patient
d) Please do not turn off power or move hard disk before LED stop
blinking
e) It is off-line clone, no need to connect with PC
USB 3.0 & eSATA
1) Moving the function switch to “PM”mode
2) Connecting docking station to power source with power cable
3) Connecting docking station to PC with USB 3.0 or eSATA cable
4) Inserting hard disk into docking station
5) Pressing “ON/OFF”button and wait. Disk indicator will light up,
when you find disk in your PC
6) Writing and reading data between hard disk and PC
Accessaries
1) DC Power Adapter
2) USB 3.0 DATA Cable
3) eSATA DATA Cable
4) Power Cord
5) User Manual
Alarm Buzzer
1) Target disk B/C/D <= source disk A
2) Finding bad tracks of hard disk during cloning
3) No target or source hard disk during cloing
クローン性能：
1）PM/cloneのスイッチをcloneの方へ移動する；
2）電源を入れる；
3）HDDをHDDベース（docking station）へ挿入；
4）“ON/OFF”ボタンを押し、電源を入れ、
指示ランプが点灯し、正常的に起動と表示する；
5）“clone”のボタンを二回押し、“BB,BB,BB”の音がし、
HDDがクローン開始する；
6）LEDの点灯により、クローンの進捗が見え、
20％～100％まで進める；
7）５つのLEDが点灯したら、提示の音がして、
完了と表示する。
注意事項：
a）Target disk B/C/Dの容量は≧Source diskの容量とする；
b）クローンが開始したら、Target disk B/C/Dはフォーマットされる；
c）クローン途中に電源を閉めたり、HDDを移動したりしないこと；
d）OFF-lineでクローンのため、ＰＣとの連接がいらない。
アラームブザー
USB3.0とe-SATA
1）Target disk B/C/Dの容量は≦source disk容量の場合；
2）HDDにFinding bad tracksが出た場合；
3）Target disk或いはsource hardがない場合。
1）functionスイッチをPMの方へ移動する；
2）電源を連結する；
3）USB3.0ケーブル或いはe-SATAケーブルによりPCと連結する；
4）HDDを入れる；
5）“ON/OFF”ボタンを押し、電源を入れ、
HDDの指示ランプが点灯する；
6）正常的なデータ読み取りに入る。
5
4