User's Manual

ManualsBrandsGloblink Technology ManualsElectronicsWireless Keypad

Table Of Contents

Targus Wireless Keypad & Mouse Set

System Requirements

Hardware

• PC with an Intel

Pentium

processor or equivalent

• USB 1.1 interface

Operating System

• Windows

98SE/Me/2000/XP

NOTE: T

HE THIRD BUTTON AND THE SCROLLING WHEEL OF THE MOUSE ONLY

WORK

WITH THE OPERATING SYSTEMS LISTED ABOVE. IF YOU USE THE MOUSE

WITH

A DIFFERENT OPERATING SYSTEM, IT WILL LOSE ITS ENHANCED FEATURES

AND

FUNCTION AS A STANDARD, TWO-BUTTON MOUSE.

Installing the Batteries

Optical Mouse

1 Remove the battery cover from the top of the mouse

by pressing the top center (over the Targus logo) and

sliding it back.

Removing the battery cover

PAKP003U-10.book Page 4 Saturday, November 5, 2005 10:55 PM

Summary of content (6 pages)

PAGE 1
PAKP003U-10.book Page 4 Saturday, November 5, 2005 10:55 PM Targus Wireless Keypad & Mouse Set System Requirements Hardware • PC with an Intel® Pentium® processor or equivalent • USB 1.1 interface Operating System • Windows® 98SE/Me/2000/XP NOTE: THE THIRD BUTTON AND THE SCROLLING WHEEL OF THE MOUSE ONLY WORK WITH THE OPERATING SYSTEMS LISTED ABOVE. IF YOU USE THE MOUSE WITH A DIFFERENT OPERATING SYSTEM, IT WILL LOSE ITS ENHANCED FEATURES AND FUNCTION AS A STANDARD, TWO-BUTTON MOUSE.
PAGE 2
PAKP003U-10.book Page 5 Saturday, November 5, 2005 10:55 PM Targus Wireless Keypad & Mouse Set 2 Insert the supplied batteries, making sure that the positive (+) and negative (-) ends of each battery match the polarity indicators inside the battery housing. WARNINGS: WHEN REPLACING THE BATTERIES, YOU MAY USE ALKALINE OR OTHER HEAVY-DUTY NIMH BATTERIES. NEVER COMBINE AN ALKALINE WITH A NIMH BATTERY IN A DEVICE. AVOID MIXING NEW AND USED BATTERIES IN A DEVICE.
PAGE 3
PAKP003U-10.book Page 6 Saturday, November 5, 2005 10:55 PM Targus Wireless Keypad & Mouse Set 3 Turn on the keypad by sliding the Power switch on the right side of the keypad to the “on” position. Connecting the Receiver To connect the receiver: 1 Plug the USB receiver into an available USB port on your computer. 2 Follow any on-screen instructions to complete the default driver installation. LED Setup key The “Lock LED” light turns on.
PAGE 4
Targus Wireless Keypad & Mouse Set Optical Mouse 1 Press and release the setup key on the receiver. The Lock LED light turns off. 2 Press the setup key on the bottom of the mouse. On/off switch Setup key When the LED on the receiver is lit, the mouse is set up with an ID and the receiver is locked. You are now ready to use the mouse. Wireless Keypad 1 Press and release the setup key on the receiver again. 2 Press the setup key on the keypad.
PAGE 5
PAKP003U-10.book Page 8 Saturday, November 5, 2005 10:55 PM Targus Wireless Keypad & Mouse Set Using the Keypad Activate Num Lock (LED illuminated) Definition of the keys: Num Lock / * BS 7 8 9 - 4 5 6 + 1 2 3 0 00 .
PAGE 6
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.