GTI-ATM2022-X-datasheet page 1 of 25 GTI-ATM2022-X Module Extreme Low Power Bluetooth 5.0 SoC Module Datasheet Rev 1.
GTI-ATM2022-X-datasheet page 2 of 25 Revision history Date Revision Nov 02, 2020 Rev 1.
GTI-ATM2022-X-datasheet page 3 of 25 Index 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. General Description ......................................................................................................................................................... 4 Key Features ..................................................................................................................................................................... 4 Specifications ...........
GTI-ATM2022-X-datasheet page 4 of 25 1. General Description The GTI-ATM2022-X module is an extreme low-power Bluetooth® 5 system-on-a-chip (SoC) solution. This innovative module design is based on the extremely low power Atmosic M2 Series Bluetooth wireless platform. The GTIATM2022-X design incorporates several innovative features that have a dramatic impact on extending the battery life of edge-of-network connected IoT products.
GTI-ATM2022-X-datasheet Keyboard matrix controller (KSM) (Note #1) Quadrature decoder for mouse input (QDEC) (Note #1) 32.768 kHz/16 MHz crystal oscillator 1.1 V to 3.3 V battery input voltage with integrated Power Management Unit (PMU) page 5 of 25 Note#1: This module is made to perform the very best of Bluetooth 5.0 functions with extremely low power. Although there are diversities of other features in the SoC which are remained in this module but are beyond the scope of this datasheet.
GTI-ATM2022-X-datasheet page 6 of 25 3.
GTI-ATM2022-X-datasheet page 7 of 25 Memory Internal 1MB embedded Flash,128KB RAM and 256KB ROM The embedded flash memory size is factory optional as below Part number Embedded Flash Memory size GTI-ATM2022-1M 1MB GTI-ATM2022-512 512KB GTI-ATM2022-128 128KB 7 / 25
GTI-ATM2022-X-datasheet page 8 of 25 4.
GTI-ATM2022-X-datasheet page 9 of 25 5.
GTI-ATM2022-X-datasheet page 10 of 25 6.
GTI-ATM2022-X-datasheet page 11 of 25 7.
GTI-ATM2022-X-datasheet page 12 of 25 8.
GTI-ATM2022-X-datasheet page 13 of 25 Bottom View (unit: mm) 13 / 25
GTI-ATM2022-X-datasheet page 14 of 25 9. Pin Description Pin Pin name I/O Description 1 GND PWR Power and signal ground 2 BT_RF RF 2.4 GHz Single-ended RF I/O for Bluetooth radio 3 WURX RF Wake receiver RF input, connect to ext. antenna 4 PWD I/O Power Down Input (Active High) 5 GND PWR Power and signal ground 6 VBAT PWR Battery Power Supply (DC 1.1 to 3.
GTI-ATM2022-X-datasheet page 15 of 25 10. Maximum Electrical Ratings Symbol Parameter Min. Typ Max. VBAT Battery supply -0.2 3.4 V VDDIO I/O supply -0.2 3.4 V VIO I/O pin -0.2 3.4 V VRF RF I/O pin (BT_RF, WURX) 10 V ESD (HBM) ESD HBM class 2 2000 V ESD (CDM) ESD CDM 500 V T-store Storage Temperature 125 ℃ -40 Unit Note: ESD(HBM) for TMC and PWD pins are 1250V 11. Recommended Operating condition Operating Condition OP-temping temperature range Min.
page 16 of 25 GTI-ATM2022-X-datasheet 12. Radio Tranceiver Characteristics (VCC=3.0V Temperature =27°C) Parameter Conditions Frequency range Rx sensitivity Min. Typical 2.402 Max. Units 24.80 GHz 37-byte packets, clean Tx 1 Mbps -95 dBm 2 Mbps -93 dBm 255-byte packets, dirty Tx dBm 1 Mbps -94 2 Mbps -91 dBm dBm dBm dBm dBm Tx output power 4, 2, 0, -2, -4, -6, -20 4 dBm -10, -20 Tx power accuracy +/- 1.
page 17 of 25 GTI-ATM2022-X-datasheet 14. GPIO Characteristics Parameter Conditions Input VIL Min. Typ Max. Units -0.2 0 0.2 V Output VOH 2 mA Load VIO-0.2 V Output VOL 2 mA Load 0.2 V 15. Embedded Flash Characteristics Parameter Conditions Min. Endurance Program/Erase 100,000 Data Retention Typ Max. Units Cycles 20 Year 16. Power consumption VBAT current at 3 V with internally generated IO supply Parameter Conditions Min. Typ Max.
GTI-ATM2022-X-datasheet page 18 of 25 17. PMU configuration There is a PMU (Power Management Unit) inside the SoC ship, below is the description of these power rails. Power rail Pin on module Input/Output description VBAT 6 I Battery or External Power Supply (DC 1.1 to 3.3V) VDDIO 19 I Power input for digital and analog I/O VDDIOP 10 O 1.8V IO power output generated by PMU VAUX 12 O The auxiliary power output of typical 3.
page 19 of 25 GTI-ATM2022-X-datasheet 18. BT5.0 BLE RF Performance test Sample under test: GTI-ATM2022-1M Test machine: IQ2011 Data rate: 1Mbps Item No. Tx power (-20 to 20dBm) Frequency offset (-150 to 150MHz) Sensitivity (≤ 70dBm) 2402MHz 2442MHz 2408MHz 2402MHz 2442MHz 2408MHz 2402MHz 2442MHz 2408MHz Ble_1M_prbs9 2# 0.45 0.81 0.66 -8.06 -6.68 -3.64 -82.5 -83.5 -84.5 Ble_1M_prbs9 4# 0.25 0.63 0.44 1.27 2.23 2.80 -84.0 -84.5 -86.0 Ble_1M_prbs9 6# 0.23 0.51 0.
GTI-ATM2022-X-datasheet page 20 of 25 19. Design notes 1. Some power rails have to be externally connected, see section-11. 2. The BT RF signal has two routes to the antenna. The 1st route goes to the PCB trace antenna through L1, The 2nd route goes to pin-2 on the module through the R1 resistor then to the external antenna, the R1 resistor is not populated as default. Using the external antenna gives better performance and a longer RF signal range.
GTI-ATM2022-X-datasheet page 21 of 25 20. Evaluation board -EVB/ DVB There is the Evaluation board (EVB or DVB) dedicated for the developmet of the GTI-ATM2022-X module, please contact us if you need it.
GTI-ATM2022-X-datasheet page 22 of 25 21.
GTI-ATM2022-X-datasheet page 23 of 25 22.
GTI-ATM2022-X-datasheet page 24 of 25 ESD CAUTION The GTI-ATM2022-X is ESD (electrostatic discharge) sensitive device and may be damaged with ESD or spike voltage. Although GTI-ATM2022-X is with built-in ESD protection circuitry, please handle with care to avoid the permanent malfunction or the performance degradation.
2.2List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions This module is stand-alone modular.If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.
GTI-ATM2022-X-datasheet page 25 of 25 23. Contacts Sales@globalscaletechnologies.com Globalscale Technologies, Inc. 1200 N. Van Buren Street Anaheim, CA 92807 U.S.A.
