GTV-380 User Manual Version 0.
Table of Content Chapter 1 Features and Specification ................................ 3 Features................................................................................ 3 Specification .......................................................................... 4 Accessories............................................................................ 7 Overview............................................................................... 9 Chapter 2 Getting Started...................................
Chapter 1 Features and Specification Features • • • • • • • • Complete car navigation solution in one box including car mount Simple touch-screen operation 4.
Specification ► System Electrical Characteristics Processor OS Flash Memory SDRAM Memory Memory Card Slot GPS Samsung S3C2440, 400MHz WinCE.NET 5.0 Default 64 MB, can up to 2GB 64MB SD/MMC SiRF Star III , built-in 18x18 Patch Antenna DISPALY Display Pixels H*W Display Type 4.3”, TFT LCD with Touch Screen 480*272 (WQVGA) COLOR TFT Transmissive Color Number 65536 colors Backlight Type LED x 7 Brightness View Angle Touch Panel Typ.
KEY BUTTON Power Press the power button to turn on the device, press it again to close any open windows and turn it off (enter a standby mode) Reset Use the stylus tip to press down the reset button through the hole to reset the system. Battery Slide Switch (ON/OFF switch) Slide to “OFF” to disable battery power supply to the system.
DVBT Tuner Channel Frequency Channel Band Width Demodulation Built-in Dual Tuner, EPG Function Support UHF / VHF (470~862 MHz / 174~230 MHz) 6 / 7 / 8 MHz COFDM with 2K / 8K FFT Receive Sensitivity -85 dBm IR Remote Control 26 Key ► GPS Specification Electrical Characteristics GPS Chipset Frequency SiRF Star III L1, 1575.42 MHz C/A Code 1.023 MHz chip rate Channels 20 channel all-in-view tracking ACCURACY Position Horizontal Velocity Time 10 meters, 2D RMS 1-5 meters 2D RMS, WAAS corrected 0.
Accessories GTV-380 Main Unit Mount DC charger AC adapter DVB-T module USB cable 7
CD or DVD (user manual, driver, Application, map data…) SD card (optional) DVB-T Antenna Quick Guide Remote control Note: If any item is missing or damaged, please contact with your local retailer.
Overview ➊ Power LED ➋ ➌ Zoom in Zoom out ➍ Menu button ➎ Mute ➏ ➐ Volume down Volume up ➑ Microphone Front View Solid Red – Battery is lower than 40%. Solid Amber – Battery is being charged. Solid Green – Battery full charged. Zoom in button. ( For Car Navigation Only ) Zoom out button. ( For Car Navigation Only ) Press the Menu button to go directly to Main Menu of the application. Press to mute the audio, press again to resume. Volume down button. Volume up button.
➊ ➋ ➌ ➍ ➎ ➏ ➐ 10 Side View and Top View Press the Power button to turn on the Power button GTV-380, press it again to turn it off (enter the standby mode). Clip groove For the cradle to clip tight to the main unit. Lanyard For you to attach a hand cord to the main unit. Hook The Navigation software, map data and other SD card slot media files can be stored in the SD card. Plug the earphone or headset to the socket, Earphone you can listen to the navigation voice guide or jack enjoy your favorite music.
Bottom View and Rear View ➊ ➋ ➌ ➍ ➎ External Antenna connector Speaker Battery Slide Switch Charging connector Docking connector For you to connect an optional MMCX-type external antenna. For output the music or navigation voice. Slide the switch to “OFF” position to prevent from accidentally turning on the device by touching the power button. If you want to use this device, be sure to slide the switch to the “ON” position. L The purpose of the Battery Slide Switch is to cut off power to the unit.
DVB-T module ➎ DVB-T Antenna connector Charging connector Infrared sensor Docking connector Clip hook ➏ DVB-T LED ➊ ➋ ➌ ➍ 12 For you to connect to DVB-T antenna. (on both sides) For power supply and battery charging. Infrared sensor for receiving signal from remote control. Docking connector for DVB-T module. For clip into the groove of the main unit. The blue LED will light when DVB-T function is operating.
Chapter 2 Getting Started Before you start to use the GTV-380, please connect it with the AC adapter and plug to power socket for battery charging. When it is in charging, the status indicator will be amber. If the battery is fully charged, the status indicator will be lit on green. Download Application Software to memory card by card reader Insert the SD card into your card reader which is connected to your PC. Insert the CD/DVD into the CD/DVD-ROM drive; the installation program will automatically start.
Click on the drive letter which your SD card is inserted, and click on “Start” button. After the download process is finished, please remove the SD card from card reader, insert it into your GTV-380 and restart it.
Attach GTV-380 to Cradle (DVB-T module) Release Lock 1. Place the GTV-380 at a downward angle into the base of the cradle. 2. Align three grooves and docking connector to push down GV-388 inward until the top clip locks into place. 3. Clean windshield glass thoroughly with glass cleaner. 4. Moisten suction cup and attach mount to the windshield. 5. Lock mount lever by moving forward. z To release, bring lever back and pull on the suction cup’s clear tab to release suction.
Charging your GTV-380 Plug the end of AC adapter or DC charger into the charging connector of GTV-380 or DVB-T module. The power LED will light. When battery is fully charged, the LED becomes green.
Chapter 3 Software Application Main Screen Main Screen z z z z z z Tap on the Navigation icon to start the Navigation application. Tap on the TV icon to start the DVBT function. Tap on the HandsFree icon to start the Bluetooth HandsFree application. Tap on the Media icon to enter the sub-screen which contains the music player and photo viewer. Tap on the Setup icon to enter the sub-screen which you can do the settings of the device.
Media Mode Media Screen z Tap on the Music icon to start the music player. z Tap on the Photo icon to start the photo viewer. Go back to Main Screen.
Music Player Music Player z In the center of screen, it shows the music title, the timer and the total length of this music. Tap this button to play the next song. Tap this button to play the current song. Tap this button to pause the playing. Tap this button to play the previous song. Tap this button to stop the playing. Sequentially play the songs from playing list. Randomly play the songs from playing list. Play all songs form playing list once and then stop playing.
Edit Playing list z Music Player will search for the “Music” folder of the SD card for all music files and display them on screen. Tap directly on the file name of the song to add or remove it from playing list. The song has been added to the list becomes blue. The song has been removed from the list becomes black. Use up or down arrow buttons to highlight the song. Tap this button to add this song to playing list. Use up or down arrow buttons to highlight the song.
Photo Viewer Photo Viewer z Photo Viewer will search for the “Photo” folder of the SD card for all supported image files and display in thumbnail mode. Use up or down arrow buttons to scroll the page. Tap to select an image and tap the Full Screen button on left side to view this image in full screen. Go back to Media Screen. Full Screen mode z Tap up or down arrow buttons on the right side to view previous or next image. Tap the close button on left top corner to end full screen mode.
Setup Mode Setup Screen z The details of these setup programs will be described in following pages. Go back to Main Screen. System Information z Display the Flash memory capacity, SD card capacity, the PCB version and the firmware version information. Go back to Setup Screen.
Power z Display remaining capacity of battery power. When AC adapter is connected to the device for charging, the battery icon will flash from right to left z The auto shut down function is only valid when GV-388 is not connected to external power. If it is connected to the AC adapter, the system will not be shut down even if you have checked this setting. Cancel and go back to Setup Screen. Save the setting you made and go back to Setup Screen.
Brightness z You can change the backlight brightness by tapping on the two bulb icons. Tap the left bulb to make the screen darker, or the right bulb to make the screen brighter. z The backlight brightness has 0~6 levels from left to right. The default is set to the 4th level. Cancel and go back to Setup Screen. Save the setting you made and go back to Setup Screen.
Regional Setting z Setup the time and date of your local area. z Select the User Interface Language and make sure your local Timezone is correctly set. Cancel and go back to Setup Screen. Save the setting you made and go back to Setup Screen. About z Display the program version information. Go back to Setup Screen.
Screen z 26 Run the screen calibration program. Press and hold the stylus on the center of the target. Repeat on four corners. When the new calibration is done, tap the screen to save the setting or wait for 30 seconds to cancel the calibration.
Chapter 4 Bluetooth HandsFree Bluetooth main screen HandsFree Phone Dialer: Tap on this button, GTV-380 will search and connect to the previous paired HandsFree device. After connection is established, it enters Phone Dialer mode. Phone Book: Tap on this button, GTV-380 will search and connect to the previous paired HandsFree device. After connection is established, it enters Phone Book mode.
Phone Dialer Backspace button Call record Dial button Phone book Go back to HandsFree Screen.
Call Record Display the missed call. Dial button Display the received call. Delete record Display the dialed call. Go back to Setup Screen.
Talking mode 30 Press this button to mute your voice. The other party could not hear your voice. Tap it again to resume. Press this button to hang up the phone. Press this button to show the extension number input screen. Press this button to switch calling source between cell phone and GTV-380.
Setup Search Device: Tap on this button to search the Bluetooth device nearby. Up to 10 devices can be searched. If pairing process is finished, it returns to Main screen. If pairing process is failed, it returns to Pin Code screen. Up to 4 Bluetooth paired devices can be stored in the list of PND. Device List: Tap on this button to enter the device list. Select the device to connect to Handsfree profile. If connection is established, it returns to Main screen.
Device List z Up to 4 Bluetooth paired devices can be stored in the device list. You can select a Bluetooth device from this list. The selected device will be highlight. Connect: Connect to the selected device and go back to main screen. If the Bluetooth device you select does not support Handsfree, you will see a warning message on screen. Delete: Delete the device from list. Go back to Setup Screen.
Set PND Name z The default name of the PND is “GPS BT Carkit”. You can change it as your wish. When you finish editing, press this button to confirm. Press this button to switch between alphabetical and numerical keypad. Backspace key to delete from the last character. Go back to Setup Screen.
Version info z Display the hardware and software version of Bluetooth module. Go back to Setup Screen.
Reset Default: Restore the factory default settings of Bluetooth. Clean Phone Book: Clean the phone book data which downloaded from you Bluetooth cell phone. Auto-Reply Setup, Default:10 sec Go back to Setup Screen.
Search and connect to your Bluetooth phone Tap on Setup icon to enter Setup mode. Tap on Search Device icon to search your Bluetooth cell phone. GTV-380 begins to search the device.
The found device is shown on the list. Tap on the device you want to connect with. If connection is established, the name of the connected device will appear on the upper right corner of screen. Answer or hang up a incoming call When you receive a incoming call, you can press the left icon to accept the call or press the right icon to refuse and hang up the call.
Make a call Tap on the Phone Dialer icon. The dialing screen appears. Input the number and tap on Dial button. The dialing screen appears. Phone call is established.
Bluetooth Stereo Playback Tap on the Stereo Playback icon, and then select your device from device list. If connection is established, it shows the A2DP screen. You can play, pause or stop music from screen buttons. Buttons for Next and Previous are also supported.
Chapter 5 DVB-T DVB-T DVB-T is the abbreviation of Digital Video Broadcasting Terrestrial. It is a broadcast transmission standard for digital terrestrial television mainly used in European area. Remote Control RADIO MUTE VOL + VOL CH + CH OK RETURN/ EXIT SETUP EPG LANGUAGE SUBTITLE NUMERIC KEY 40 Switch to Radio channel, press it again to resume TV mode. Mute the volume output. Press it again to resume. Volume up Volume down Channel up Channel down Confirm for selecting item.
Enter TV Mode z If you want to watch TV program, you have to attach GTV-380 main unit onto DVB-T module and plug in the charging adapter.
z While you are in TV mode, you can touch anywhere on screen to display the OSD (On Screen Display) menu. z If there is no touch action within 3 seconds, the OSD menu will disappear automatically. Main Setup screen Close and back to previous screen. Enter Electronic Program Guide. Enter Multichannel television sound. Enter Setup screen. Select subtitle language. 42 Switch channel.
z If your TV program supports Multichannel television sound, you can choose to listen the different language or audio. z You can choose to display a different subtitle if the TV program supports this function.
z Tap on the up or down arrow icon to switch channel. The channel information will display for seconds and disappear automatically. z EPG displays the program title, descriptive information and the time schedule of previous and next program.
Setup screen z Display the related information of the program.
z Select your country location. z Select the OSD language.
z Automatically search the channel of your local area. z Manually search the channel signal.
z Select from the TV program list or Radio program list. z z 48 Reset the system to Factory default. Tap on to confirm. Tap on to Cancel. Display system version information.
Chapter 6 Troubleshooting If the GTV-380 does not boot up successfully or does not function properly 1. Please check if the Application software is properly installed in the SD memory card. 2. Please check if the SD memory card is inserted into the SD expansion slot. 3. Please check the battery power. (The red light indicates the battery power is low and needs to be charged. The amber light indicates that it is in charging status, and the green light will be on when the battery is fully charged.) 4.
L If your car windows equipped with Window Films for reducing heat and blocking the harmful UV rays, it may also slightly affect the receiving of GPS signal. Thus, the cold start time will take longer then usual. L If the car is moving, it may also affect the time for GPS fix. We suggest that you stop the car while you turn on the GTV-380 for a quicker GPS fix time. L Please avoid excessive heat and humidity. Please do not leave the GTV-380 in your car under the direct sunshine with windows closed.
Safely Remove Hardware Before you remove the memory card from the card reader, or before you unplug the USB cable from the device or USB port, please safely remove the hardware by the following processes: 1. Double click the "Safely Remove Hardware" icon from the task bar on the right bottom corner of desktop. 2. Select the hardware device and then click the "Stop" button. 3. Confirm by selecting the device again and click "OK" button. 4.
FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Exposure requirements: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.