Hit “Enter” on PPP and you can setup the following: Users_edit – Edit users profile. Address_pool – Config dynamic assigned address pool. Authenticate – User authentication policy. Assign_address – Peer address assignment policy. Wan_pppoe – WAN port PPPoE function. ISP Hit “Enter” on ISP and you will prompt to input the ISP profile number.
Hit “Enter” on Ip_share and you can setup the following: Pat – Config port address translation. Nat – Config network address translation. DHCP Hit “Enter” on DHCP and you can setup the following: Generic – Configure generic DHCP parameter. Fixed – Configure Fixed host IP address list. Client – DHCP client functionality. Client_interface – DHCP client activate interface number. DNS Proxy Hit “Enter” on DNS Proxy and you can setup DNS_proxy server name and its IP address.
Tftp Hit “Enter” on Tftp and you can setup the IP address for Tftp server. Route Hit “Enter” on Route and you can setup Static – To configure the static route parameters. Rip – To configure RIP protocol module parameter.
Hit “Enter” on Bridge you can setup Generic – To configure bridging function, IP and subnet mask. Static – To configure static bridging parameter. WLAN Hit “Enter” you are able to configure, SSID Channel – Current operating frequency channel. Tx_rate – Transmission Rate Basic_rate – Basic rate. Station name – station name Rts Threshold – Rtx threshold. FragThreshold – Fragmentation threshold (even numbers only) Weprequired – Enable/Disable WEP function. DefaultKeyID – WEP default key ID.
PPP – Show PPP configuration. IP_share – Show IP address sharing configuration. DHCP – Show DHCP configuration. Route – Show routing configuration Bridge – Show bridging configuration. ISP – Show ISP profiles. WLAN – Show wireless LAN configuration. Access-List – Show access control rules pool. Inspect – Show inspection setting or rules pool. Reset_Default Hit “Enter” on reset_default and type “y” for yes and “n” for no to reset to default setting.
Hit “Enter” on reboot and type “y” for yes and “n” for no to restart system and activate new system configuration. Su Hit “Enter” on su to switch to supervisor mode, it will prompt you for supervisor password. Sys_info Hit “Enter” on sys_info and it will take you to a status screen.
Ping Hit “Enter” on ping and it will prompt you for a IP address to ping to. Exit Hit “Enter” on exit to disable privileged command or disconnect.
Section 6 How to Configure Your PC to Connect the Gateway Router If you do not wish to set a static IP address on your PC, you will need to configure your PC to accept the IP address that your gateway will provide. 1. Click Start button, select Settings, then Control Panel 2. Double-click the Network Icon 3. In the configuration windows, select the Internet Protocol that has been associated with your network card/adapter. If there is no TCP/IP line listed, you will need to install the TCP/IP now.
4. Click the Properties button, then choose the IP ADDRESS tab. Select Obtain an IP address automatically. 5. Then select DNS configuration tab to add DNS IP address. If you do not wish to add DNS you can disable DNS function. Press OK. You have completed the client settings. 6. After clicking OK, windows will ask you to restart the PC. Click Yes. Confirm Your PC’s IP Configuration There are two tools which are great for finding out a computer’ s IP configuration: MAC address and default gateway.
gateway is 192.168.1.1. The default gateway should be the network device IP address. The MAC address in windows 95/98 is called the Adapter Address. l IPCONFIG (for windows 2000/NT/XP) In the DOS command type IPCONFIG and press Enter. Your PC IP information will be displayed as shown below. This concludes the user manual. Should you require further assistance or have other inquires please contact your distributor.
Appendix A Specifications Hardware Specification Architecture SAMSUNG ARM7 embedded Operating System supports Supertask M/B Form Factor 7.5”x5.5” CPU Support SAMSUNG ARM7 Memory Flash: 1Mbyte SDRAM: 8Mbyte Compatibility: Devices supporting IEEE802.11b wireless standards Frequency Band: 2400-2483.4 MHz Wireless Medium: Direct Sequence Spread Spectrum Radio data rate: 1, 2, 5.5 and 11Mbps Modulation:DBPSK@1Mbps,DQPSK@2Mbps, CCK@5.5 and 11Mbps Chipset: Intersil PRISM II.
Appendix B Glossary Access Point ─ An internetworking device that seamlessly connects wired and wireless networks. Ad-Hoc ─ An Ad-Hoc wireless LAN is a group of computers each with LAN adapters, connected as an independent wireless LAN. Authentication Type ─ Indication of an authentication algorithm which can be supported by this node: Open System : Open System authentication is the simplest of the available authentication algorithms. Essentially it is a null authentication algorithm.
PLCP ─ physical layer convergence protocol PPDU ─ PLCP protocol data unit Preamble Type ─ During transmission, the PSDU shall be appended to a PLCP preamble and header to create the PPDU. Two different preambles and headers are defined : the mandatory supported long preamble and header which interoperates with the current 1 and 2 Mbps DSSS specification as described in IEEE Std 802.11-1999, and an optional short preamble and header.
