Assembly Instructions

ManualsBrandsGlobal Industrial ManualsBin Racks & ShelvingGlobal Industrial Steel Shelving with 30 4"H Plastic Shelf Bins Green, 36x12x39-7 Shelves

1. Create the right side of the shelving units by laying two uprights side-by-side on a flat surface.

Be sure that the short side of the uprights is facing up, as shown in Figure 1.

Important: One side of the uprights

is longer that the other, and contains

two sets of holes. When laying the

uprights side-by-side, this long side

should be on the floor, and the short

side should be facing up.

2. Attach the two side sway braces, beginning in the 20th

hole from the top of each upright (approximately 20" from the top),

using two

/4"-20 x

/8" bolts and nuts. The side sway braces attach

to the longer side of the uprights (the side with two sets of holes). Bolt

the braces into the small holes near the edge of the uprights as shown.

Note the hole pattern of two round holes and then one square hole,

repeating every 3", which should help facilitate proper placement of the

bolts. Finger tighten only at this point.

3. Attach the other end of both sway braces. The information below will

tell how many holes should be between the top and bottom of the sway braces.

Count the holes carefully, as an incorrect count will cause the upright to be the

wrong depth to hold the shelves.

4. Repeat steps 1-4 for the left uprights.

Tools Required:

•

/16" nut driver or socket

• Flathead screwdriver.

• Requires two people

for assembly.

• Approximate assembly time:

15 to 30 minutes per unit.

Note: Number of shelves

per unit varies depending

on unit purchased.

OPEN INDUSTRIAL SHELVING

Assembly

Instructions

Customer Service

1-800-645-2986

Starter

Starter & Add On

Back-To-Back

Unit Depth Brace Length Distance Between Bolts

12" 30" 27 holes (27

/2")

18" 30" 24 holes (24

/2")

24" 30" 19 holes (19

/2")

30" 30" 10 holes (10

/2")

Summary of content (4 pages)

PAGE 1
Assembly Instructions Customer Service 1-800-645-2986 OPEN INDUSTRIAL SHELVING Tools Required: • 7/16" nut driver or socket • Flathead screwdriver. • Requires two people for assembly. • Approximate assembly time: 15 to 30 minutes per unit. Note: Number of shelves per unit varies depending on unit purchased. Starter Starter & Add On 1. Create the right side of the shelving units by laying two uprights side-by-side on a flat surface.
PAGE 2
You should now have complete left and right sides of your shelving unit, with sway brace bolts and nuts still finger-tightened only. 5. Have an associate hold one upright on it’s side while you bolt the bottom shelf on each post, as shown below. 6. Bolt on other upright to bottom shelf. 7. Bolt the top shelf, flat side up, into the top holes of both uprights. A B 8. While unit is still lying down, bolt the rear sway braces on the back of the unit, using five 1/4"-20 x 5/8" bolts and nuts, as shown.
PAGE 3
A 11. For added strength and reinforcement, place two 1/4"-20 x 5/8" bolts and nuts (not included) through each corner of each shelf, and into the small holes of the upright. 12. If more than one unit is to be used in a row, assemble a new unit with 1/4"-20 x 1" bolts and nuts. The pair of side braces on the first unit becomes a common pair for the two units.
PAGE 4
13. If two units are to be placed back-to back, the back braces on the first unit become a common pair for the two units. A B 1a. 14. For added shelf strength, insert shelf reinforcement channel 1a. (sold separately) into bottom of shelf. Place on an angle and turn into shelf channels as pictured above.