Self cleaning Hot & Cold Hidden Bottle Water Cooler with Display Model # 8LDIECH-SC-WFC-SSF USER MANUAL User of mineral water please read descaling instructions on the page 14 TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING DISPENSER. SAVE THIS MANUAL FOR FUTURE USE For service call: 1-844-452-2425 or send E-mail to: help@glacialhome.com 8LDIECH-SC-WFC-SSF © 2016 Electrotemp Technologies Inc.
SAFETY PRECAUTIONS ! WARNING To reduce risk of injury and property damage, user must read this entire manual before assembling, installing & operating dispenser. Failure to execute the instructions in this manual can cause personal injury or property damage. This product dispenses water at very high temperatures. Failure to use properly can cause personal injury.
SAFETY PRECAUTIONS --Electrical Requirements WARNING ! Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in serious injury, fire, or electrical shock. A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended.
TABLE OF CONTENTS Safety Precautions ............................................................. Safety Precautions - Electrical Requirements ................... Key Information for Future Use ......................................... Specifications .................................................................... Parts & Features ............................................................... Assembly ............................................................................
SPECIFICATIONS Power Supply AC 120V/60Hz/6.5Amp. Refrigerant Type R-134A Cold Water Power <100Watts Cold Capacity / Peak Hour 1 Gallon / 3.79 L Cold Temp Range 3°C – 10°C / 37.4°F – 50°F Hot Water Power 650 Watts Hot Capacity / Peak Hour 1.59 Gallon / 6 L Hot Temp Range 80°C – 92°C / 176°F – 197.6°F Dimensions 32.0 W x 38.2 D x 102.8 H (cm) 12.6 W × 15.0 D × 40. 5 H (inch) 16.75 Kg / 36.
ASSEMBLY Keep plastic bags away from children. 1. Remove dispenser from packaging. 2. Unpack drip tray and insert into dispenser. 3. Remove protective packaging from around probe. 4. Properly dispose all of packaging. CLEANING PRIOR TO INITIAL USE Your water cooler is Clean Out of The Box. Cleaning described below is not required. However if you choose to clean your water cooler for any reason, please follow the instructions below. Time Required: 45 minutes. 1.
11. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser. HOT WATER Remove drain cap and silicon plug. Cool water will immediately flow into the bucket. Several seconds later hot water will dispense. Be mindful to avoid injury. 12. Once the unit has drained, replace the silicon plug and drain cap. 13. Remove the remaining water from the reservoirs by dispensing from the cold tap into a pitcher. Rinsing 14. Repeat steps 2 to 13, but this time using clean tap water.
OPERATION This dispenser is intended for water dispensing only. Do NOT use other liquids. Do NOT use for other purposes. Warranty is void if used for any other liquids including coffee, tea, juices, beer or wine. This dispenser has been designed to use water bottles with a 3, 5 or 5.2 gallons capacity. Do NOT use alternative bottles. 2. This model uses an pump to force water from the bottle to the reservoirs: a. Please do the following: i. Clean bottle cap and neck. ii.
• If the lights continue to flash, your bottle may be empty or there may be an issue with water tube lines.Call 1-844-452-2425 for assistance. 4. Plug cord into a properly grounded wall outlet. Water will be pumped into the hot and cold water reservoirs from the bottle. • 5. Turn energy saving switches on back of dispenser to ON. • The red switch controls the heating of water. If you do not want hot water, leave this switch OFF. • The blue switch controls the cooling of water.
The circular shapes in the drip plate help align the flow of water. This unit dispenses water at a fast rate. To avoid splashes, hold cup as close to the tap as possible. Depress right control downward to start flow. Release control once desired fill level is achieved. • 2. 3. Dispense Hot Water This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children and pets away from unit while dispensing.
Guide for installation and use of BRITA JUGFILTER FILTER CARBON Filtration System Your cooler is supplied with an empty housing for installing brite jug filter cartridge. Filter cartridge not supplied brite filter cartridge is good for refilling 15x5 gallon bottles of tap water. Viva brand two in one, combo sediment and activated carbon filter are available to order please call 1-844-452-2425. Viva filter can be refilled with 50 bottles. Refile counter set for 15 bottles.
PROPER CARE & DESCALING General Cleaning Perform: As needed Time Required: 5 minutes. Notice: Do NOT use abrasive materials or chemical cleaners. 1. Clean cabinet surfaces with a soft cloth and warm soapy water. 2. Wipe dust from back of dispenser to improve efficiency. 3. Remove drip tray assembly by sliding it forward. Remove cover. Place tray and cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water. Sanitizing Perform: Every 12 months or whenever an off-taste occurs.
8. Remove remaining water from reservoir by dispensing from the cold tap into a pitcher. Step B: Sanitize Probe and Taps 1. In a clean bucket, make a sanitizing solution of 1.5 gallons of tap water and 3 tablespoons of unscented household bleach. 2. Wipe probe and area around all taps with a soft cloth moistened with the sanitizing solution. Step C: Sanitize Reservoirs 1. Remove the cap from a spare empty 5 gallon bottle. 2. Fill the bottle with the water and bleach mixture. 3.
7. Allow the water to fill the empty reservoirs. 8. Wait 10 minutes then turn energy saving switches OFF and unplug the power cord. 9. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser. HOT WATER 10. Remove drain cap and silicon plug. Cold water will immediately flow into the bucket. Several seconds later hot water will dispense. Reminder - Place drain cap and silicon plug in a safe location so they are not lost. 11.
2. Attach or insert the probe to the bucket/bottle. 3. Place the bucket/bottle into the cooler and close the door. The water will be pumped up into the holding tanks. 4. Plug in the cooler and turn on the hot switch located at the back of the cooler. Do not turn on the cold-water switch. 5. Wait for 1 hour. 6. Unplug the cooler from the wall 7. Using rear drain plug, drain the water from the cooler into a bucket and discard the water. A. Locate the white plastic cap at the back of the cooler. B.
The cleaning function • The cleaning function every 4 hours to be automatic operation time. • 6 times for one Day, time were 12 PM, 4 PM, 8 PM, 12 AM, 4 AM, 8 AM. • Execution since before and after CLEANING function 1 minute, the screen prompt SELF CLEANING, said it was the CLEANING. SELF CLEANING SELF CLEANING Self cleaning forecast function • Display the clock 30 seconds after appear a self-cleaning NEXT SELF CLEANING AT forecast, remind users from cleaning in the next time.
TROUBLESHOOTING Problem: Stainless steel surfaces are smudgy or fingerprinted. Solution: Use paper towel to wipe excess oils until surface feels dry to the touch. • To maintain beauty of stainless steel, oil it periodically using a stainless steel cleaning solution available at hardware stores, or use mineral oil (unscented baby oil). Problem: The buttons for dispensing water are slow-moving or jammed. Solution: Dust and cooking oils might cause slow moving push buttons.
LIMITED WARRANTY Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date of purchase from an authorized retailer or distributor.