User's Manual

ManualsBrandsGilbar ManualsElectronicsCard Reader Transmitter

Table Of Contents

Tribrid Card Reader Installation Manual

Pre

imina

/04

MDE-4770 Tribrid Card Reader Installation Manual · June 2008 Page 1

Introduction

Purpose

This manual provides installation instructions for installing the M07999B001 Tribrid Card

Reader (TCR). The TCR is used in Encore

S EMV units only.

This equipment has been tested and found to comply with the limits pursuant to Part 15

of the Federal Communications Commission (FCC) Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy, and if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by the manufacturer could void the

user’s authority to operate this equipment.

The long term characteristics or the possible physiological effects of radio frequency

electromagnetic fields have not been investigated by Underwriters’ Laboratories, Inc.

(UL

IMPORTANT INFORMATION

Table of Contents

Topic Page

Introduction 1

Important Safety Information 4

Installation of the TCR 6

• Installing the M07999B001 TCR in an Encore S EMV Unit

(without Contactless Card Reader Option)

• Installing the M07999B001 TCR in an Encore S EMV Unit (with

Contactless Card Reader Option)

Required Reading

Before installing the Card Reader, the installer must read, understand, and follow:

• This manual

• NFPA 30A, The Automotive and Marine Service Station Code

• NFPA 70, The National Electric Code

• Applicable federal, state, and local codes and regulations

Failure to do so may adversely affect the safe use and operation of the equipment.

Note: This installation must be performed by a Gilbarco

Authorized Service Contractor

(ASC) to ensure warranty.

MDE-4770

Tribrid Card Reader Installation Manual

June 2008

Summary of content (20 pages)

PAGE 1
MDE-4770 Tribrid Card Reader Installation Manual June 2008 Introduction Purpose l im 06 in /0 ar 4/ 08 y This manual provides installation instructions for installing the M07999B001 Tribrid Card Reader (TCR). The TCR is used in Encore® S EMV units only. IMPORTANT INFORMATION P re This equipment has been tested and found to comply with the limits pursuant to Part 15 of the Federal Communications Commission (FCC) Rules.
PAGE 2
Introduction Required Tools Parts Lists lim in a ry The following tools are required to install the TCR: • Isopropyl alcohol (END-1082) • Nut drivers, 1/4-inch, 8 mm, 3/8-inch, 9/32-inch socket with long extension • Putty knife • Gilbarco Diagnostic card • CSC test card • Ratchet set, standard • Screwdrivers, flat blade and cross tip • Static guard wrist strap The following table provides the parts included in the TCR Kit.
PAGE 3
Introduction Abbreviations and Acronyms Description ADA American Disabilities Act CRIND Card Reader in Dispenser CSC Contactless Smart Card EMV Chip Cards Euro Plus/Mastercard®/Visa® Chip Cards ESD Electrostatic Discharge PCA Printed Circuit Assembly POS RF TCR Point of Sale Radio Frequency Tribrid Card Reader Transmitter/Receiver in Dispenser P TRIND re lim in ar y Term MDE-4770 Tribrid Card Reader Installation Manual · June 2008 Page 3
PAGE 4
Important Safety Information Important Safety Information Read the Manual Read, understand and follow this manual and any other labels or related materials supplied with this equipment. If you do not understand a procedure, call a Gilbarco Authorized Service Contractor or call the Gilbarco Support Center at 1-800-800-7498. It is imperative to your safety and the safety of others to understand the procedures before beginning work.
PAGE 5
Important Safety Information In an Emergency No Open Fire Open flames from matches, lighters, welding torches or other sources can ignite fuels and their vapors. re lim in ar y No Sparks - No Smoking Sparks from starting vehicles, starting or using power tools, burning cigarettes, cigars or pipes can also ignite fuels and their vapors. Static electricity, including an electrostatic charge on your body, can cause a spark sufficient to ignite fuel vapors.
PAGE 6
Installation of the TCR Installation of the TCR Installing the M07999B001 TCR in an Encore S EMV Unit (without Contactless Card Reader Option) Removing the Existing Card Reader ry To remove the existing Card Reader, proceed as follows: lim in a Note: Read all instructions before beginning and observe all safety precautions. 1 Obtain an approval from the store manager or responsible personnel to remove the unit from service. 2 Remove AC power to the unit using the station circuit breaker.
PAGE 7
Installation of the TCR Figure 1: Rear View of the Encore S Main Door with Card Reader Cable Harness Connection P Fastener re lim in ar y Fastener Installing the Encore TCR Assembly To install this assembly, proceed as follows: 1 Remove the adhesive backing from the Card Reader gasket (M00682B001) and place the gasket over the Card Reader opening from the inside of the open main door. CAUTION A properly grounded ESD wrist strap must be worn when performing step 2.
PAGE 8
Installation of the TCR 5 From the rear of the main door, position the Card Reader and then the Card Reader bracket on the door, such that the Card Reader slot (see Figure 2) is positioned on the top. Loosely secure the Card Reader bracket and Card Reader to the main door using the two Q11677-26 screws (provided in the kit) in the top and bottom two holes (looking from the back of the Card Reader).
PAGE 9
Installation of the TCR 7 Reconnect the 6-pin power/data cable (M07702A006) to the 6-pin power/data connector (see Figure 2 on page 8) on the TCR. Note: Tie-wrap the loose end of the cable to ensure that it does not interfere with the other wires. 8 Connect the appropriate end of M07702A006 to P205 and P206 on the Serial Interface PCB (M07793A001) (see Figure 4).
PAGE 10
Installation of the TCR P re lim in a ry Figure 5: Serial Interface PCB (M07793A001) P109 9 Locate the ground ring terminal on the lower portion of the EMV CRIND display mounting bracket and remove the screw that secures the ground connection. Retain the screw for reinstallation. 10 Connect the ring terminal (see Figure 3 on page 8) of the ESD Ground cable (M07709A001) to the EMV CRIND display mounting bracket ground connection.
PAGE 11
Installation of the TCR Commissioning the Dispenser/Updating CRIND Software For EMV units, after installing the TCR, you will have to commission the dispenser. At this point, you may also update the EMV CRIND software using the SPOTUpdate tool. For detailed instructions on how to commission the dispenser and update the EMV CRIND software, refer to MDE-4771 EMV CRIND Start-up/Service Manual.
PAGE 12
Installation of the TCR Installing the M07999B001 TCR in an Encore S EMV Unit (with Contactless Card Reader Option) Removing the Existing Card Reader To remove the existing Card Reader, proceed as follows: Note: Read all instructions before beginning and observe all safety precautions. ry 1 Obtain an approval from the store manager or responsible personnel to remove the unit from service. lim in a 2 Remove AC power to the unit using the station circuit breaker.
PAGE 13
Installation of the TCR Figure 6: Rear View of the Encore S Main Door with Card Reader Cable Harness Connection P Fastener re lim in ar y Fastener Installing the Encore TCR Assembly To install this assembly, proceed as follows: 1 Remove the adhesive backing from the Card Reader gasket (M00682B001) and place the gasket over the Card Reader opening from the inside of the open main door. CAUTION A properly grounded ESD wrist strap must be worn when performing step 2.
PAGE 14
Installation of the TCR 5 From the rear of the main door, position the Card Reader and then the Card Reader bracket on the door, such that the Card Reader slot (see Figure 7) is positioned on the top. Loosely secure the Card Reader bracket and Card Reader to the main door using the two Q11677-26 screws (provided in the kit) in the top and bottom two holes (looking from the back of the Card Reader).
PAGE 15
Installation of the TCR 7 Reconnect the 6-pin power/data cable (M07702A006) to the 6-pin power/data connector (see Figure 7 on page 14) on the TCR. Note: Tie-wrap the loose end of the cable to ensure that it does not interfere with the other wires. 8 Connect the appropriate end of M07702A006 to P205 and P206 on the Serial Interface PCB (M07793A001) (see Figure 9).
PAGE 16
Installation of the TCR P re lim in a ry Figure 10: Serial Interface PCB (M07793A001) P109 9 Locate the ground ring terminal on the lower portion of the EMV CRIND display mounting bracket and remove the screw that secures the ground connection. Retain the screw for reinstallation. 10 Connect the ring terminal (see Figure 8 on page 14) of the ESD Ground cable (M07709A001) to the EMV CRIND display mounting bracket ground connection.
PAGE 17
Installation of the TCR Installing the Antenna PCA (M08285A001) The RF antenna must be located directly behind the area where the MasterCard PayPass®, American Express® ExpressPaySM and other logo graphics are attached as shown in Figure 11.
PAGE 18
Installation of the TCR 2 Remove the narrow sealing gasket from the exposed TRIND lens space on the outside of the door and replace it with the TRIND gasket (M06010B002). 3 Locate the M08285A001 Antenna PCA placed on the TRIND CSC Reader Lens (M05987B002) and place it over the TRIND gasket. Secure the TRIND CSC Reader Lens by installing and tightening the four screws (M00419B117) (see Figure 13).
PAGE 19
Installation of the TCR Commissioning the Dispenser/Updating CRIND Software For EMV units, after installing the TCR, you will have to commission the dispenser. At this point, you may also update the EMV CRIND software using the SPOTUpdate tool. For detailed instructions on how to commission the dispenser and update the EMV CRIND software, refer to MDE-4771 EMV CRIND Start-up/Service Manual.
PAGE 20
Installation of the TCR lim in ar y 7 Obtain the FCC Decal (M02962B011) from the kit and install it under the patent label. P re Patent Label TRIND FCC Label Nameplate (M02962B011) American Express® is a registered trademark of American Express Co. CRIND®, Eclipse®, Encore®, Gilbarco®, and TRIND® are registered trademarks of Gilbarco Inc. ExpressPaySM is a service mark of American Express Co. MasterCard® and PayPass® are registered trademarks of MasterCard International, Inc.