User's Manual

ManualsBrandsGilbar ManualsElectronicsRF Identification Device Module

Table Of Contents

MDE-3591A TRIND

™

/TIRIS

™

Retrofit Kits C00011-002-XXXX • 11/00 Page 1

PRELIMINARY

FCC 11/30

Introduction

Purpose of this Manual

This manual provides instruction for installing TRIND™/TIRIS™ Retrofit Kits

C00011-002-XXXX in The Advantage

Series and MPD

-3 units with InfoScreen

monochrome CRIND™, or single-line CRIND.

The TRIND option allows customers to automatically authorize CRIND-equipped

units, using either a hand-held or auto-mounted transponder provided by a major

oil company (MOC). Use these kits for one- or two-sided units. Kits are customer

specific, depending on unit type, number of sides, and MOC.

Retrofit Kits C00011-002-XXXX are configured according to specific unit

requirements.

Prerequisites

Before installing any TRIND kit, ensure that the existing CRIND contains the

following.

• Z-180 logic board and software (T17764-XX), which is not configured in

TRIND retrofit kit. Refer to MDE-2628, Cash Acceptor Retrofit Assemblies for

The Advantage Series Units with CRIND Card Reader in Dispenser Kit

C00007-002.

• Plastic options doors for single-line/cash acceptor InfoScreen/cash acceptor

and monochrome/cash acceptor

Important Notice

This equipment has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses and

can radiate radio frequency energy, and if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense. Changes or modifications not expressly approved

by the manufacturer could void the user’s authority to operate this equipment.

MDE-3591A

TRIND™ Transmitter/Receiver in Dispenser

Retrofit Kits C00011-002-XXXX

Using TIRIS™ Technology

Installation

Summary of content (62 pages)

PAGE 1
MDE-3591A Installation TRIND™ Transmitter/Receiver in Dispenser Retrofit Kits C00011-002-XXXX Using TIRIS™ Technology Introduction Purpose of this Manual This manual provides instruction for installing TRIND™/TIRIS™ Retrofit Kits C00011-002-XXXX in The Advantage® Series and MPD®-3 units with InfoScreen®, monochrome CRIND™, or single-line CRIND.
PAGE 2
Introduction Required Reading Before installing the equipment, the installer must read, understand, and follow: • this manual • NFPA 30A, The Automotive and Marine Service Station Code • NFPA 70, The National Electric Code • applicable federal, state and local codes and regulations • ASC TRIND Technology Update on page 18 Failure to do so may adversely effect the safe use and operation of the equipment.
PAGE 3
Introduction Required Tools The following equipment is needed to install TRIND™ kit C00011-002 • Allen wrench set, American standard • square (carpenter’s, 12'' • clean cloth or rag • center punch • chip extraction tool, e.g., IC extraction, Digikey Part No.
PAGE 4
Parts Lists Parts Lists C00011-002-XXXX Kit Configurations by Suffix -Suffix Configured For -WF_S The Advantage® Series 48" (wide frame) single-sided See -WF_D The Advantage Series 48" (wide frame) double-sided -NF_S The Advantage Series 36" (narrow frame) single-sided page 4 -NF_D The Advantage Series 36" (narrow frame) double-sided -MPDS MPD®-3 single-sided with PMI bezel (slide-in faceplate) -MPDD MPD-3 double-sided with PMI bezel (slide-in faceplate) -MPBS MPD-3 single-sided with Mack
PAGE 5
Parts Lists The Advantage Series Narrow Frame (36’’) Kits Kits C00011-002-NF_S and C00011-002-NF_D kits for The Advantage® Series 36" (narrow frame) single-sided (NF_S) and double-sided (NF_D) units contain the following.
PAGE 6
Parts Lists MPD®-3 Series Kit Parts MPD-3 Units with PMI Bezels (Slide-in Faceplates) C00011-002-MPDS Kits for single-sided units and C00011-002-MPDD Kits for double-sided units with PMI bezels and slide-in faceplates contain the following.
PAGE 7
Parts Lists MPD-3 Units with Mack Bezels (Bolt-on Faceplates) C00011-002-MPBS Kits for single-sided units and C00011-002-MPBD Kits for double-sided units with Mack bezels and bolt-on faceplates contain the following.
PAGE 8
Parts Lists ASC TRIND™ Tool Kit K94577-01 Tool Description Part Number co-axial cable tool Q13628-01 Quantity 1 field strength sensor Q13626-01 1 test tag, TI/RFIDcar mount Q13630-01 1 test tag, TI/RFID hand held Q13630-02 1 threaded rod, 3/8-16 x 4" N23880-01 4 tuning tool, plastic tipped Q13631-01 1 Y R A N I M I L 0 3 E / R 1 P C1 C F Page 8 MDE-3591A TRIND™/TIRIS™ Retrofit Kits C00011-002-XXXX • 11/00
PAGE 9
Important Safety Information Important Safety Information This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found.
PAGE 10
Important Safety Information Read the Manual Read, understand and follow this manual and any other labels or related materials supplied with this equipment. If you do not understand a procedure, call a Marconi Authorized Service Contractor or call the Marconi Call Center at 1-800-800-7498. It is imperative to your safety and the safety of others to understand the procedures before beginning work.
PAGE 11
Important Safety Information Prevent Explosions and Fires Fuels and their vapors will become explosive if ignited. Spilled or leaking fuels cause vapors. Even filling customer tanks will cause explosive vapors in the vicinity of dispenser or island. No Open Flames Open flames from matches, lighters, welding torches or other sources can ignite fuels and their vapors.
PAGE 12
Important Safety Information Field Wiring Poorly wired pumps or dispensers could cause a fire, explosion or electrical shock. Place all power and lighting wires in threaded, rigid metal conduits. Plug all unused junction box holes. Never use knockout boxes or flexible conduit. Tighten all threaded connections and covers. Do not use gaskets with junction box covers. Do not disturb sealing compound around wires at junction box entrances. Use factory method of routing wires.
PAGE 13
Important Safety Information React Quickly to Fuel Spills, Fires or Vehicle Impact Follow these steps in the event of a fuel spill, fire, or vehicle impact. 1 Use station EMERGENCY TOTAL ELECTRICAL SHUT-OFF immediately. Turn off all system circuit breakers to the island. WARNING The EMERGENCY STOP, ALL STOP, and PUMP STOP buttons at the cashier’s station WILL NOT shut off electrical power to the pump/dispenser. This means that even if you activate these stops, fuel may continue to flow uncontrolled.
PAGE 14
Important Safety Information Emergency and First Aid Information Refer to phone book for emergency phone numbers. If needed, follow first aid instructions as outlined in American Red Cross Standard First Aid manuals. WARNING Gasoline ingested may cause unconsciousness and burns to internal organs. Do not induce vomiting. Keep airway open. Oxygen may be needed at scene. Seek medical advice immediately.
PAGE 15
Important Safety Information Warning Labels Several types of warning labels appear on Marconi products to inform and remind users of important safety information. Read, understand and follow these warnings. Sample Warning Label The following labels are typical of those you may find on Marconi’s products: Y R A N I M I L 0 3 E / R 1 P C1 C F Working Alone It is highly recommended that someone who is capable of rendering first aid be present during servicing.
PAGE 16
Important Safety Information Other Useful Safety Information This subsection provides additional safety information. OSHA Lock-Out and Tag-Out Requirements OSHA Standard 29 CFR 1910-147 Control of Hazardous Energy Sources (Lock-Out/Tag-Out) covers ways to avoid personal injury because power was turned on or fuel pressure was applied unexpectedly while servicing equipment. The rule requires: (1) Turning off equipment power and fuel under pressure (2) Use of a locking device (breaker, valve, etc.
PAGE 17
Important Safety Information Classifying Hazardous Locations Any activity that can cause an explosion (e.g., smoking, drilling, etc.) must be done well outside the vapor area. The following diagrams are based on NFPA 30A, section 6 and NFPA 70, section 514. Fuel is present.
PAGE 18
ASC TRIND™ Technology Update ASC TRIND™ Technology Update Page 18 READ THIS SECTION BEFORE PROCEEDING WITH INSTALLATION ATTENTION: AUTHORIZED SERVICE CONTRACTORS The TRIND™ system utilizes technology and devices not commonly used in the industry. Read the following carefully to familiarize yourself with relatively unique aspects of TRIND and prevent field problems. RF Transmission and Antennas Located in the TRIND card cage is a transmitter printed circuit board (PCB).
PAGE 19
Installation Instructions for All Kits Installation Instructions for All Kits Before beginning read “Classifying Hazardous Locations” on page 17 and “ASC TRIND™ Technology Update” on page 18. Preparing Exxon Light Boxes Use these procedures for dispensers with Exxon light boxes only. For units without light boxes, proceed to ‘Preparing for Installation’ on page 19. 1 Open and lift display frames on both long sides of display and lock in-place according to light box manufacturer’s instructions.
PAGE 20
Installation Instructions for All Kits Removing Knockout in Unit Top Cover 1 Remove knockout from left side of unit top cover while facing ‘B’ side for The Advantage units or ‘A’ side for MPD-3 units. Note: For units with light box, this will require lifting side of light box for access, by loosening and/or removing hardware as described in Step 4 of “Preparing Exxon Light Boxes” on page 19.
PAGE 21
Installation Instructions for The Advantage® Series Units Installation Instructions for The Advantage® Series Units For MPD-3 Series, go to “Installation Instructions For MPD®-3 Units” on page 35. 1 From ‘A’ side of unit, remove inner sheathing on left column. Set sheathing and screws aside for reassembly. Removing inner sheathing Outside sheathing Inside sheathing and screws ‘A’ side Y R A N I M I L 0 3 E / R 1 P C1 C F 2 Open main access doors.
PAGE 22
Installation Instructions for The Advantage® Series Units 5 Remove door mounting pin and right options door. Removing options door Door mounting pin Right options door Y R A N I M I L 0 3 E / R 1 P C1 C F 6 Dispose of door. Save pin for reassembly.
PAGE 23
Installation Instructions for The Advantage® Series Units Modifying Right Options Door For 48" units without stop or call button on right options door, and all 36" units, go to ‘Re-installing Door Alarm Switches’ on page 25, if unit has door alarm. If unit does not have door alarm, go to “Installing Right Options Door” on page 25. For 48" units with stop or call buttons previously installed, perform the following steps.
PAGE 24
Installation Instructions for The Advantage® Series Units 2 Mark placement of pump stop or call button on new right options door by measuring from door edges as shown. Hole location for pump stop or call button 1 9/16" 3 3/16" Y R A N I M I L 0 3 E / R 1 P C1 C F 3 Away from fuel island, drill a 7/8 inch diameter hole in the location shown above. Remove any burrs around hole with deburring tool or rounded file.
PAGE 25
Installation Instructions for The Advantage® Series Units Re-installing Door Alarm Switches For units with cash acceptors, follow these steps to re-install door alarm assemblies on TRIND™ right option doors. Refer to diagram on this page for more information. Perform each step for both ‘A’ and ‘B’ side right option doors. If unit does not have door alarm, go to ‘Installing Right Option Door’ on page 25. 1 Re-install C-clips removed from old right side option doors.
PAGE 26
Installation Instructions for The Advantage® Series Units Installing Bulkhead Grommet 1 Disconnect two cables and remove ground connector to ‘A’ side printer. Remove printer from unit and save for reinstallation. 2 While facing ‘A’ side of unit, measure 6" in toward center of cabinet top from outside edge of top, and draw a line on top cover. Locating bulkhead grommet hole 'A' Side 10.5" 6" Y R A N I M I L 0 3 E / R 1 P C1 C F 'B' Side 3 Measure 10.5" in from left side of top, and draw a line.
PAGE 27
Installation Instructions for The Advantage® Series Units 8 Follow these mandatory safety guidelines: • Do not use electric drill. Use only pneumatic (air) drill set or controlled for low speed only (300-500 rpm) or hand operated drill. • Deposit a few drops of cutting oil at drilling point and on drill bit, to keep bit from binding, to quench sparks and to bind drill shavings.
PAGE 28
Installation Instructions for The Advantage® Series Units Installing Card Cage Assembly Install card cage assembly from ‘B’ side of unit according to the following steps: 1 Carefully pry out printer cable retainer from underside of printer shelf. 2 Pull printer cable out of 2 3/4" round hole from bottom, and install piece of strip grommet Q10315-06 around perimeter of hole. 3 For all single-sided units, connect dummy load connector R20526-01 to JB on low frequency transmitter PCB Q13579-01 in card cage.
PAGE 29
Installation Instructions for The Advantage® Series Units Installing Transmitter Cables M00878A002 Cable Assembly PB P2B P1B P3B P3A P1A P2A PA Before proceeding be sure to be able to easily identify A and B side cable ends. Electric tape, wire numbers or other suitable device may be used. Note: Sharp bends in antenna cables will cause damage. All cable turns must be in loops and gradual. Refer to “ASC TRIND™ Technology Update” on page 18.
PAGE 30
Installation Instructions for The Advantage® Series Units 8 Without removing top sheathing, install piece of edge grommet Q10315-06 along edge of top sheathing where cables pass in column. See exploded illustration below. Note: Carefully check for any points where cable harness is run where cables may come in contact with sheet metal edges, and install edge grommet to prevent cable damage.
PAGE 31
Installation Instructions for The Advantage® Series Units Replacing Main Cabinet Top Cover 1 Use hacksaw to cut 3/8" slots in cabinet top cover to allow strip a minimum of 6" wide to be folded back with pliers and hammered flat as shown, to allow cables to pass under top cover to grommet. Note: Remove top cover from work area to cut slot. Do not cut metal in proximity to dispensers. Place top cover on cardboard while hammering to prevent damage to paint.
PAGE 32
Installation Instructions for The Advantage® Series Units Pull Out CRIND Tray For these units utilize round 2-3/4" hole in printer shelf bottom, used for printer cable. Use cable clamps to secure cables to underside of printer shelf.
PAGE 33
Installation Instructions for The Advantage® Series Units 5 Being sure that option door opens and closes freely without stressing or crimping cables, use tie wrap Q10178-01 to loosely secure cables to small fixed tab at end of light frame, forcing cables between light frame and door gasket.
PAGE 34
Installation Instructions for The Advantage® Series Units T20662-G2 Cable Routing In Main Cabinet Card Cage cable harness T20662-G2 contains two cables with connectors P1 and P2. P1 for A Side is shorter of the two. Each cable is designed to extended to the point where the main door and electronics cabinet are hinged. Feed cables through 2-3/4" round hole in printer shelf.
PAGE 35
Installation Instructions For MPD®-3 Units Installation Instructions For MPD®-3 Units Before beginning read “Classifying Hazardous Locations” on page 17 and “ASC TRIND™ Technology Update” on page 18. The TRIND™ retrofit can only be done on MPD-3 units with CRIND™ printer on left. Preparing For Installation 1 From ‘A’ side, remove left column outside sheathing (or top section only for two piece sheathing).
PAGE 36
Installation Instructions For MPD®-3 Units Removing Main Cabinet 1 Locate four nuts on each side of main cabinet, ‘A’ and ‘B’, that secure cabinet to frame. Removing main cabinet Four nuts each side, ‘A’ and ‘B’, on mounting studs behind lip + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + Y R + A N I M I L 0 3 E / R 1 P C1 C F 2 Remove all eight nuts and washers, and save for reassembly.
PAGE 37
Installation Instructions For MPD®-3 Units Installing Transmitter Cables cables connections to card cage M00878A002 Cable Assembly cable connections for upper housing PB P2B P1B P3B P3A P1A P2A PA Before proceeding be sure to be able to easily identify A and B side cable ends. Electric tape, wire numbers or other suitable device may be used as needed. Note: Sharp bends in antenna cables will cause damage. All cable turns must be in loops and gradual.
PAGE 38
Installation Instructions For MPD®-3 Units 5 Loop cables below hole and back up through hole and out of column. 6 Feed cable ends into vapor barrier, dressing and securing cables in place with electrical tape. 7 Away from island, use snips or shears to cut slits 1-1/2" apart in bottom center of inside sheathing at 45 degree angles. See illustration below. 8 Fold pieces forward on cabinet side of sheathing. Use hammer to flatten folded pieces as shown.
PAGE 39
Installation Instructions For MPD®-3 Units Removing Faceplate MPD-3 units have two types of faceplates; slide-in (PMI bezel) and bolt-on (Mack bezel). Follow directions for the type of faceplate and bezel that applies. For units with slide-in faceplates on PMI bezels, do the following: 1 Release right side faceplate using keyswitch. 2 Open manager keypad door and remove single screw.
PAGE 40
Installation Instructions For MPD®-3 Units Routing Cables into Main Cabinet 1 Open bezel doors on main cabinet. 2 Locate indent on rear of door behind 3/4" diameter unopened access point. 3 Use 3/4" drill bit to open hole in plastic door from rear of door. Note: If electric drill is used work must be 20’ from fuel island. 4 Use deburring tool or file to round edges of hole.
PAGE 41
Installation Instructions For MPD®-3 Units Installing Card Cage Assembly Install card cage assembly from ‘A’ side of unit, according to the following steps: 1 Begin to separate card cage assembly into two pieces by removing one screw on top and two nuts at bottom, one each front and rear. Card cage assembly Screw Nut Nut 2 Disconnect cables joining two sides of card cage. Y R A N I M I L 0 3 E / R 1 P C1 C F 3 From ‘A’ side, place bottom section of card cage fuse side first on to left shelf.
PAGE 42
Installation Instructions For MPD®-3 Units Installing TRIND™ Faceplate Assembly. Perform the following steps for each side of unit. For installing TRIND slide-in faceplates on PMI bezels, do the following: 1 Remove new TRIND faceplate assembly from box. For ‘B’ side faceplates only, feed faceplate cables back into faceplate housing through round hole in shield to shorten cable leads. Note: ‘B’ side cables have a shorter run to card cage than ‘A’ side. 2 Peel adhesive backing off round gasket N23881-01.
PAGE 43
Installation Instructions For MPD®-3 Units 3 Replace the door gasket removed in step 2 with adhesive backed gasket Q11659- 01. 4 Replace existing keypad and keypad cable with T17549-G1 keypad and long cable R18163-G1, but do not install keypad on bezel door. Note: At user’s discretion, new keypad can be placed behind brand panel lighting or in the well behind the printer door, on either side of printer, provided cable is run and secured properly and safe access is maintained.
PAGE 44
Installation Instructions For MPD®-3 Units Routing Cables in Main Cabinet Kit comes with ten cable clamps (Q13558-04). Routing cables in main cabinet Bundle cables between shelf wall and card cage, using clamp Install Q10277-02 strip grommet for power cable R20580-G1 ‘B’ side Y R A N I M I L 0 3 E / R 1 P C1 C F Existing snap-in 1 1/2" bushings- use for routing Install strip grommet Q10277-02 in 1-1/2" hole for power cable R20850-01.
PAGE 45
Instructions for All Units Instructions for All Units Installing Overhead Antennas and Brackets For All Units Do the following: antenna box bracket Y R A N I M I L 0 3 E / R 1 P C1 C F screw slot 1 For each antenna assembly mounting box, remove screw. 2 Slide bracket slot over mounting box until antenna is secured in bracket. 3 Replace screw. For Units Without Light Boxes Note: For units with Light Boxes proceed to “For Units With Exxon Light Boxes” on page 47.
PAGE 46
Instructions for All Units 2 Center gaskets with lifting hook holes and install adhesive side down. 3 Peel adhesive backing off large gasket N23959-01. 4 Center gasket with knockout hole and install adhesive side down. Routing Antenna Cables to Upper Housing Bracket cable channel Cable connectors Bracket Y R Antenna gasket A N I M I L 0 3 E / R 1 P C1 C F 1 Carefully feed connector ends of P1A/B and P3A/B cables through antenna gasket on knockout opening to upper housing.
PAGE 47
Instructions for All Units Do the following: 1 For brackets attached to cable side of antenna assembly, be sure that cables are contained in raised bracket channel. 2 For all brackets, with or without cables, position rubber washer, metal washer and lifting bracket removed in “Preparing For Installation” on page 19 over bracket mounting hole. 3 Secure with bolt removed in “Preparing For Installation” on page 19. Repeat for all brackets and sides.
PAGE 48
Instructions for All Units 5 Remove antenna and bracket assembly from top of Light Box. 6 Use carpenter’s square to draw line from long side of Light Box to mark. 7 Measure along line 6 3/4'' from Light Box long side and mark with center punch. 8 Drill 7/8'' diameter hole at center punch mark. Use file to clean sharp edges and burrs from hole perimeter.
PAGE 49
Instructions for All Units Sealing Antenna Bracket with Cables on All Units antenna assembly mounting box access end of cable channel screw Y R A N I M I L 0 3 E / R 1 P C1 C F To seal bracket cable channel (each side) do the following: 1 Loosen both screws holding each antenna assembly to bracket. 2 Pull antenna and mounting box out from bracket and allow antenna to lower, to allow sealing of access end of bracket cable channel with RTV sealant.
PAGE 50
Instructions for All Units Upper Housing Connections Without Light Box Do the following to connect M00878A002 cable harness assembly to antenna: 1 For A Side, inside upper housing: • Connect P1A on harness to J1 low frequency antenna cable. • Connect P3A on harness to J2 high frequency antenna cable. 2 Fro B Side, inside upper housing: • Connect P1B on harness to J1 low frequency antenna cable. • Connect P3B on harness to J2 high frequency antenna cable.
PAGE 51
Instructions for All Units 7 Make the following cable connections in Light Box: • Connect P1A on cable harness to A Side J1 antenna cable. • Connect P2A on cable harness to A Side J2 antenna cable. • Connect P1B on cable harness to B Side J1 antenna cable. • Connect P2B on cable harness to B Side J2 antenna cable. 8 Make the following cable connections in upper housing: • Connect P1A on M00878A001 harness to J1A on extension assembly M01380A001 assembly.
PAGE 52
Instructions for All Units R20773-G2 P2 J1/J2 Cable Block Diagram R20762 Y R Page 52 T20662-G2 R20773-G2 J1/J2 P2 A N I M I L 0 3 E / R 1 P C1 C F MDE-3591A TRIND™/TIRIS™ Retrofit Kits C00011-002-XXXX • 11/00
PAGE 53
Instructions for All Units Connections for power supply cable R20580-01 are unit specific. Plug three prong female end into three-prong receptacle of card cage (see “Card Cage Assembly T20606-G2” on page 54), and use appropriate connector to intercept power on unit power cable by installing R20580-01 in-line. Note: Check whether brand panel lighting ballast is connected to power supply.
PAGE 54
Instructions for All Units Card Cage Assembly T20606-G2 Back Side Power supply (Regulator) PCB T20314-G1 Tab for securing to shelf divider Data control board Q13563-04 JB for ‘B’ side or R20526-G1 dummy load connector B JA for ‘A’ side Y R A N I M I L 0 3 E / R 1 P C1 C F A J2A A J2B B Transmitter (low freq) PCB assembly Q13579-01 Front Side P250 on TIRIS Gateway PCB T20128-G3 Recessed male three prong power receptacle UL® label B A J8 for ‘B’ side J7 for ‘A’ side RS232 port Page 54 MDE-3
PAGE 55
CRIND® BIOS TRIND™ Multi 1 Upgrade CRIND® BIOS TRIND™ Multi 1 Upgrade Units must have current Z-180 CRIND logic board. Install the CRIND Bios TRIND software K93744-01, one per logic board, on the T17764-XX CRIND logic board(s) according to the following steps. Note: A properly grounded electrostatic discharge wrist strap must be worn during this procedure.
PAGE 56
CRIND® BIOS TRIND™ Multi 1 Upgrade 1 Locate and remove existing BIOS at U7 on CRIND® logic board T17764-XX using a grounded chip removal tool. Grounding strap Chip removal tool Y R A N I M I L 0 3 E / R 1 P C1 C F 2 Install TRIND BIOS K93744-01 (one per logic board) at position U7, orienting notch on chip with indication mark on board as shown. 3 Install jump jack on JP-16 for each side of unit. Note: Jumper on JP-16 informs the CRIND that a TRIND system is present.
PAGE 57
Dispenser Set-Up Dispenser Set-Up Addressing Dispenser Each dispenser on the G-Site controller must be addressed differently; no two dispensers may have the same address. Address is at discretion of the installer. Follow these steps: 1 From A side of unit, locate dip switches on power supply board (PCB) T20314-G1 in card cage. 2 Using switches 2, 3, 4 and 5 address each dispenser according to the following table: Note: Switch one in down position is standalone mode selected, used for service only.
PAGE 58
Dispenser Set-Up Addressing Gateway Board Address for TRIND™ must match address on CRIND® logic board. Follow these steps: 1 Access unit’s CRIND logic board. Refer to MDE-2562 CRIND Service Manual. 2 Locate jump jacks on A and B side CRIND logic boards T17764-XX. 3 Note position of jump jacks and set jump jacks on Gateway board T20128-G3 to match address on CRIND logic boards for both A and B sides.
PAGE 59
Dispenser Set-Up Preparation for Tuning Antennas Antenna tuning requires use of field strength sensor Q13626-01 supplied with ASC tool kit. 1 For units without G-Site™ put unit in ‘Stand Alone’ mode by disconnecting J4 on the DCB board and placing jumper on light microreader board at JP3. Note: JP3 and J4 can never both be in or both out. One and only one must always be in, the other out. 2 If applicable, restore CRIND tray to operating position. 3 Restore power to unit(s) and cold start the CRIND.
PAGE 60
Dispenser Set-Up 3 On card cage, move three position ‘tune’ toggle switch from center position to ‘A’. ‘Tune’ toggle switch location B A A B Y R A N I M I L 0 3 E / R 1 P C1 C F 4 Connect leads on multi-meter set to DC voltage to field strength sensor. 5 By fine adjustments to tuning pot, set to highest DC voltage reading. Note: Voltage will peak at a point, and then decrease with turns in either direction. Set at peak.
PAGE 61
Dispenser Set-Up Testing TRIND™ 1 From ‘A’ side of unit touch hand held test tag (Q13630-02 from the ACS TRIND tool kit) to TRIND target graphic. Door or faceplate TRIND indicator will light. Note: If indicator fails to light check whether light on other side is on; if so it indicates a crossing of ‘A’ and ‘B’ side cables. Check connections.
PAGE 62
Dispenser Set-Up Completing Installation After all testing has been completed, do the following: 1 Shut off all power to the unit. 2 Replace or refasten all components and hardware, including: • Replace all sheathing and/or pans removed. • For units with Light Boxes, replace and tighten all mounting hardware. 3 Close all secure all doors, including Light Box doors (if present). 4 Clean up work site, removing all materials to be discarded and all tools. 5 Reapply power and Cold Start the unit.