Certification Exhibit FCC ID: N6SGCM IC: 827B-GCM FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0087.W06.11.A Manufacturer: Gilbarco, Inc. Model: FlexPay Contactless Manual 5015 B.U.
MDE-4939 FlexPay™ Contactless Module Installation and Service Manual May 2011 Introduction Purpose This document provides instructions to mount the FlexPay™ Contactless Module and to install the Contactless Interface Board on Secure Card Reader 2 (SCR2). IMPORTANT INFORMATION P r 05 el /0 im 5/ in 11 a ry This equipment has been tested and found to comply with the limits pursuant to Part 15 of the Federal Communications Commission (FCC) Rules.
Introduction Table of Contents Topic Page 1 Important Safety Information 5 Mounting the FlexPay Contactless Module on Encore S Enhanced Dispenser Equipped with SPOT EMV CRIND 7 Mounting the FlexPay Contactless Module on The Advantage Series Dispensers 10 Mounting the FlexPay Contactless Module on Encore 300 and Encore 500 Dispensers 11 Mounting the Contactless OTI Module on Encore 300 (Pre-EMV) Dispensers 12 Mounting the FlexPay Contactless Module on Encore 500 S Dispensers 12 Mounting the Fl
Introduction Item Description Part Number 4 Thread Forming Screw Q11677-24 Quantity 4 5 Screw Phillips Pan Head Sems Metric Q12845-36 4 6 Hex Nut Metric M01114B001 4 7 Nylon Washer M12184B001 4 8 Cable <
Introduction Item Description Part Number 4 Thread Forming Screw Q11677-24 Quantity 3 5 Screw Phillips Pan Head Sems Metric Q12845-36 4 6 Hex Nut Metric M01114B001 4 7 Nylon Washer M12184B001 4 8 Cable <
Important Safety Information Important Safety Information Note: Save this Important Safety Information section in a readily accessible location. This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining, or servicing this product. Before performing any task on this product, read this safety information and the applicable sections in this manual, where additional hazards and safety precautions for your task will be found.
Important Safety Information In an Emergency No Open Fire Open flames from matches, lighters, welding torches, or other sources can ignite fuels and their vapors. No Sparks - No Smoking Sparks from starting vehicles, starting or using power tools, burning cigarettes, cigars, or pipes can also ignite fuels and their vapors. Static electricity, including an electrostatic charge on your body, can cause a spark sufficient to ignite fuel vapors.
Mounting the FlexPay Contactless Module on Encore S Enhanced Dispenser Equipped with SPOT EMV CRIND Mounting the FlexPay Contactless Module on Encore S Enhanced Dispenser Equipped with SPOT EMV CRIND <
Mounting the FlexPay Contactless Module on Encore S Enhanced Dispenser Equipped with SPOT EMV CRIND 4 Assemble the Bracket and the FlexPay Contactless Module using the four screws, four Nylon Washers, and the four nuts provided in the kit (see Figure 3).
Mounting the FlexPay Contactless Module on Encore S Enhanced Dispenser Equipped with SPOT EMV CRIND 7 Connect the SPOT Contactless Cable to the P201 port on the M07793A001 SPOT Printed Circuit Board (PCB) as shown in Figure 5 (ii) and to the COM2 port on the SPOT EMV CRIND display as shown in Figure 6. Figure 5: Connecting the SPOT Contactless Cable <
Mounting the FlexPay Contactless Module on The Advantage Series Dispensers Mounting the FlexPay Contactless Module on The Advantage Series Dispensers <> To mount the FlexPay Contactless Module on The Advantage Series Dispensers, proceed as follows: 1 Remove the existing Contactless Reader, if present.
Mounting the FlexPay Contactless Module on Encore 300 and Encore 500 Dispensers Mounting the FlexPay Contactless Module on Encore 300 and Encore 500 Dispensers <> To mount the FlexPay Contactless Module on Encore 300 and Encore 500 Dispensers, proceed as follows: 1 Remove the existing Contactless Reader, if present.
Mounting the Contactless OTI Module on Encore 300 (Pre-EMV) Dispensers Mounting the Contactless OTI Module on Encore 300 (Pre-EMV) Dispensers <> Mounting the FlexPay Contactless Module on Encore 500 S Dispensers y <> To mount the FlexPay Contactless Module on Encore 500 S Dispensers, proceed as follows: in ar 1 Remove the existing Contactless Reader, if present.
Mounting the FlexPay Contactless Module on Eclipse Dispensers 3 Mount the assembled bracket, the Spacer, and the OTI Module on the dispenser using the three screws provided in the kit (see Figure 13). Figure 13: Mounting the Assembled Bracket on the Dispenser P re lim in ar y Screws Mounting the FlexPay Contactless Module on Eclipse Dispensers <
Mounting the FlexPay Contactless Module on FlexPay OPT Dispensers 3 Mount the assembled bracket and the OTI Module on the dispenser using the three screws provided in the kit (see Figure 15). Figure 15: Mounting the Assembled Bracket on the Dispenser in ar y Assembled Bracket Mounting the FlexPay Contactless Module on FlexPay OPT Dispensers lim <
Installing the Contactless Interface Board on SCR 2 2 Install the Upper Mounting Bracket and the new screw provided in the kit for the Contactless Communication PCB (see Figure 17).
Installing the Contactless Interface Board on SCR 2 Figure 18: Installing the Contactless Interface PCB <
Installing the Contactless Interface Board on SCR 2 4 Connect the Contactless Interface PCB Interconnect Cable to the Card Reader as shown in Figure 19. Note: Both the ends of the Contactless Communication PCB Interconnect Cable have the same connector, so either end may be used.
Installing the Contactless Interface Board on SCR 2 Connecting the OTI Module to the Contactless Interface Board Connect the OTI Module to the Contactless Interface Board as shown in Figure 20. Figure 20: Connecting the OTI Module in ar y OTI Module Connecting Power to the Contactless Communication Board lim Connect the Power Cable to the Contactless Communication Board as shown in Figure 21.
Configuring SPOT EMV CRIND for FlexPay Contactless Module Configuring SPOT EMV CRIND for FlexPay Contactless Module To configure the SPOT EMV CRIND for FlexPay Contactless Module, proceed as follows: 1 Power-up the SPOT EMV CRIND. A white screen with the Gilbarco® logo and software package version is displayed momentarily (see Figure 22). P re lim in ar y Figure 22: Software Packages Screen <1> enter setup appears at start-up and also when the FlexPay Card Reader requires activation. 2 Press 1.
Configuring SPOT EMV CRIND for FlexPay Contactless Module 3 Enter the right-most six digits of the PPN and press ENTER/OK. The Service Menu - Main Menu is displayed (see Figure 24). Note: If you do not enter the password within 60 seconds, the unit automatically restarts. in ar y Figure 24: Service Menu - Main Menu lim 4 Press 3. The System Configuration Menu is displayed as shown in Figure 26.
Configuring SPOT EMV CRIND for FlexPay Contactless Module 5 Press 2 to change Contactless Card Reader to OTI (see Figure 26). P re lim in ar y Figure 26: System Configuration Menu - Contactless Card Reader Select 6 Press OK to save the changes and exit. The display goes back to the Service Menu (see Figure 27). Figure 27: Service Menu 7 Press Cancel. The SPOT EMV CRIND restarts.
Verifying Functionality of FlexPay Contactless Module Through CRIND Diagnostics (Generic CRIND) Verifying Functionality of FlexPay Contactless Module Through CRIND Diagnostics (Generic CRIND) IMPORTANT INFORMATION As an additional security measure, the FlexPay CRIND Keypad requires that the Enter key be pressed after any number entry (in Diagnostic Mode only). 1 Enter CRIND Diagnostics by swiping the CRIND Diagnostics Card into the Card Reader.
Verifying Functionality of FlexPay Contactless Module Through CRIND Diagnostics (Generic CRIND) 3 Press 2 > Enter. The Device Config menu is displayed (see Figure 30). P re lim in ar y Figure 30: CRIND Diagnostics - Device Config Menu 4 Press 5 > Enter. The Card Reader Menu is displayed (see Figure 31). Figure 31: CRIND Diagnostics - Card Reader Menu 5 Press 3 > Enter. The Test RF Card Menu is displayed (see Figure 32).
Verifying Functionality of FlexPay Contactless Module Through CRIND Diagnostics (Generic CRIND) 6 Press 1 > Enter. The Test RF Card screen is displayed (see Figure 33). in ar y Figure 33: CRIND Diagnostics - Test RF Card Screen 7 Present the RF card as shown in Figure 34. P re lim Figure 34: Presenting the RF Card If a valid read is made, Figure 35 is displayed.
Affixing FlexPay Contactless FCC Label Affixing FlexPay Contactless FCC Label Affixing the M02962B015 FlexPay Contactless FCC Label on the Dispenser Inner Sheathing Obtain the FlexPay Contactless FCC Label (M02962B015) from the kit and install it under the patent label as shown in Figure 36. Figure 36: Affixing the M02962B015 FlexPay Contactless FCC Label <
lim in ar y P re CRIND®, Eclipse®, Encore®, Gilbarco®, The Advantage® Series, and TRIND® are registered trademarks of Gilbarco Inc. FlexPay™ is a trademark of Gilbarco Inc. MasterCard® is a registered trademark of MasterCard International Inc. Phillips® is a registered trademark of The Phillips Screw Co. UL® is a registered trademark of Underwriters’ Laboratories Inc. Visa® is a registered trademark of Visa Inc. © 2011 Gilbarco Inc.