User Instructions

ManualsBrandsGigaset Communications ManualsElectronicsDECT module

16.09.2011

Page 1 of 6

OEMinstructions



Themanufactureroftheendproductshallconsiderthefollowinghints:



1)Theendproduct(host)withthemodulebuiltinsidemustbemarkedasfollows:



ContainsTransmitterModuleFCCID:TVU‐MD40/IC:8023A‐MD40

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmful

interference,and(2)thisdevicemustacceptanyinterferencereceived,including

interferencethatmaycauseundesiredoperation.

ModuletransmetteurIDIC:8023A‐MD40.

Sonfonctionnementestsoumisauxdeuxconditionssuivantes:(1)cetappareilnedoitpas

causerd’interférencesnuisibleset(2)appareildoitacceptertouteinterferencerecue,y

comprislesinterferencesquipeuventpertuberlefontionnement.



2)Thefollowingregulatorystatementsshallbeprintedintheusermanualfortheend

product.



FCCInformation:

Changesormodificationstotheequipmentnotexpresslyapprovedbythepartyresponsible

forcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassBdigital

device,pursuanttoPart15oftheFCCRules.Operationissubjecttothefollowingtwo

conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)Thisdevicemust

acceptanyinterferencereceived,includinginterferencethatmaycauseundesired

operation.

Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceina

residentialinstallation.Thisequipmentgenerates,usesand

canradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful

interferencetoradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.If

thisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,which

can

bedeterminedbyturningthesystemoffandon,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

1.Reorientorrelocatethereceivingantenna.

2.Increasetheseparationbetweentheendproductandreceiver.

3.Connecttheendproductintoanoutletonacircuitdifferentfromthattowhichthe

receiverisconnected.

4.ConsultthedealeroranexperiencedradioTVtechnicianforhelp.



Summary of content (6 pages)

PAGE 1
OEM instructions The manufacturer of the end product shall consider the following hints: 1) The end product (host) with the module built inside must be marked as follows: Contains Transmitter Module FCC ID: TVU‐MD40 / IC: 8023A‐MD40 Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Module transmetteur ID IC: 8023A‐MD40.
PAGE 2
Industry Canada Information: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. NOTICE: The Industry Canada label identifies certified equipment.
PAGE 3
Single or limited‐single modules and the RF front‐end section of a split or limited split‐ module must be a separate physical assembly that can be installed into (or attached to) a host as a separate sub‐assembly (daughter‐board sub‐assembly). The method used for input and output electrical connections to the host can be soldered, cabled, wired, or use plug‐in connectors. A module cannot be solely the implementation of a design specification.
PAGE 4
Requirements additional to those specified in common safety standards may be necessary for: ‐ Equipment intended for operation in special environments (for example, extremes of temperature, excessive dust, moisture or vibration, flammable gases and corrosive or explosive atmospheres). ‐ Equipment intended to be used in vehicles, on board ships or aircraft, in tropical countries or at altitudes greater than 2000 m. ‐ Equipment intended for use where ingress of water is possible.
PAGE 5
) Installation guide The module shall be operated only with the voltage stated in the specification. The module contains an internal fuse which is implemented as a track on the PCB. The fuse is tripped at a current of 3 ‐ 4A. The module has to be exchanged if the fuse is blown. The MD40 is intended to be fixed at the host board with two M2.5 screws on distance bolts. The two distance bolts must have a length of 6.2mm (+‐ 0.2mm) and a diameter of 4mm (+‐ 0.5mm).
PAGE 6
For optimum performance, an antenna generally needs to be surrounded by an unobstructed space a few wavelengths in size. Any dielectric or conducting material in the immediate vicinity of an antenna affects the radiation pattern and performance of the antenna. Hence, whenever mechanical design allows, as much space as possible must be left clear around the antenna spring (min. 40mm). This ensures that the impact of surrounding PCBs or other conducting parts (cables etc.