Installation Instructions

ManualsBrandsGIGA-TMS ManualsElectronicsRFID Reader

Transmit Frequency

OPERATING

Transponder

Interface

ELECTRICAL

MECHANICAL

ENVIRONMENTAL

Power Input

Current Consumption

Dimensions

Weight

Temperature

Humidity

125KHz /13.56MHz Standard

1-Wire / RS-232

10 to 48 VDC

About 30 mA @12VDC

Length : 82.6 mm / Width : 47 mm / Height : 17 mm

110 gm (With Cable)

Operating : -20 ℃ to 70 ℃

Storage : -30 ℃ to 80 ℃

Operating : 10 % to 90 % noncondensing

Storage : Up to 90% noncondensing

Cable Length 90 cm +/- 2cm

Reading distance 2~5 cm Typ

H4001 / H4002 / EM4100/4102 EM card

ISO14443A Mifare, DESFire, Ultralight card

TM951343 Page 1

FL20S is EM/Mifare UID Reader with 1-Wire

and RS232 interface, designed to integrate with

vehicle trackers and the other controllers.

With 10~48VDC power input, it’s convenient to

install the reader in different vehicles. It aims to

offer more flexibility to build solutions at

affordable cost, can be used alternatively for

iButton and get your solution working with low

cost EM and Mifare cards.

Frequency: 125KHz and 13.56MHz

Read UID of H4001 / H4002 / EM4100/4102 EM card

Read UID of ISO 14443A Mifare, DESFire card

Support data Output 1-Wire, RS232

Support the other 1-Wire input interface

Available to install on metal surface

Available to install on different vehicles

Weather resistant

Summary of content (7 pages)

PAGE 1
FL20S is EM/Mifare UID Reader with 1-Wire and RS232 interface, designed to integrate with vehicle trackers and the other controllers. With 10~48VDC power input, it’s convenient to install the reader in different vehicles. It aims to offer more flexibility to build solutions at affordable cost, can be used alternatively for iButton and get your solution working with low cost EM and Mifare cards. Frequency: 125KHz and 13.
PAGE 2
LIMITED WARRANTY Giga-Tms warrants that the products sold pursuant to this Agreement will perform in accordance with GigaTms’s published specifications. This warranty shall be provided only for a period of one year from the date of the shipment of the product from Giga-Tms (the “Warranty Period”). This warranty shall apply only to the “Buyer” (the original purchaser, unless that entity resells the product as authorized by Giga-Tms, in which event this warranty shall apply only to the first re-purchaser).
PAGE 3
Front View Bottom View 1 2 PIN 1 3 1 LED Indicator Red Description On Off Standby Blink Off Read OK Off Blink Read Error On On ISP Mode RS232 TX Green VCC 2 Sound Indicator Buzzer Description 1-WIRE Bi- Read OK GND Bi-Bi-Bi Read Error 3 6 Pin Terminal Pin 1 2 3 4 5 6 Color Red Black Blue Purple White Yellow Signal VCC GND 1-Wire 1-Wire TX RX Description Power Input: 10~48 Volts Power Ground DATA In/Out To Next Device RS232 TX (transmit) RS232 RX (receive) TM951343 Page 3
PAGE 4
Baud Rate : 19200,N,8,1 All 1-Wire devices, including iButton devices, contain an 8-byte unique registration number. The computation begins with the MSB of the 64-bit, This 1-Wire Data consists of an 8-bit CRC, a unique 48-bit serial number and an 8bit family code. Baud Rate : 19200,N,8,1 The start character is factory defined as an ‘STX’ (02 HEX). This is followed by 8 Hex characters of data for Mifare Card,10 Hex characters of data for EM Card. The CR\LF characters serve to bring the received screen te
PAGE 5
The default interface for FL20S is 1-Wire. For RS232 interface, please follow its pin assignment as below and use software to set up interface. 1.Connect the FL20S unit with your computer. RS232 RED BLACK WHITE YELLOW VDD GND TX RX 2.Download 1-Wire Reader Configure software from below link for installation: http://ftp.gigatms.com.tw/disks/disk5478 A. Select the COMPort and click the “open” to execute sofeware. B.Click the “RS232 Output” and “Exit”.
PAGE 6
CAUTION: The crossed out wheeled bin label that can be found on your product indicates that this product should not be disposed of via the normal household waste stream. To prevent possible harm to the environment or human health please separate this product from other waste streams to en-sure that it can be recycled in an environmentally sound manner. For more details on available collection facilities please contact your local government office or the retailer where you purchased this product.
PAGE 7
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.