User's Manual

ManualsBrandsGiant Telecom ManualsElectronics2.4GHz 40 Channel Analog Modulation Cordless Phone

Giant -309 Operation Manual (2.4GHz Cordless + CID)

Revision 1

Page1of22

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce

the risk of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire.

They may explode. Check with local codes for possible special disposal instructions.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF

USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

SAVE THESE INSTRUCTIONS

Summary of content (22 pages)

PAGE 1
Giant -309 Operation Manual (2.4GHz Cordless + CID) IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm.
PAGE 2
Giant -309 Operation Manual (2.4GHz Cordless + CID) MAIN FEATURES OLYMPIA OL2430 CORDLESS PHONE FEATURES : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 2.4GHz 40 channels auto scanning operation Manual channel selection 65536 Random combinations of security code Last number re-dial (32 digits max.) Power saving in standby mode.
PAGE 3
Giant -309 Operation Manual (2.4GHz Cordless + CID) 15 Battery low indication (‘Battery Low’ text display on the 3rd line ) CORDLESS OPERATION Channel frequencies H/S TX CH.
PAGE 4
Giant -309 Operation Manual (2.4GHz Cordless + CID) 1. Power Up 1.1. After power up, the handset should place on the cradle of the base unit for setting a new security code for communication 1.2. Each time when the handset place on the cradle of the base unit, the base unit will generate and transmit a new security code to the handset unit through the RF Link.(The both unit will use the 1st channel for the security code transfer operation) 1.3.
PAGE 5
Giant -309 Operation Manual (2.4GHz Cordless + CID) 4. Terminate a call 4.1. To terminate a call, either by pressing the “TALK” button, the handset will emit a beep indicating call is terminated successfully. 4.2. By placing the handset on the cradle, call is terminated and ‘Security code set up’ procedure will be performed. 4.3. Handset will emit a error beep if it cannot receive ‘talk off ACK’ from the base unit.
PAGE 6
Giant -309 Operation Manual (2.4GHz Cordless + CID) 8. Setting local area code 0 0 0 AREA CODE? 8.1. You need enter 3 digits from number pad. Three digits will be shift to left one by one, after you enter one digit. E.g. [Press “1”, display “ 001”] à [Press “2”, display “012”] à [Press “3”, display “123”] 8.2. Press “MEMO” key to confirm. After confirmation, it will enter Tone/Pulse setting. 9. Setting Tone/Pulse SET T/P? T 9.1. It will display current T/P setting first 9.2.
PAGE 7
Giant -309 Operation Manual (2.4GHz Cordless + CID) 11. Setting handset LED ON/OFF/CON LED ON 11.1. It will display current “LED ON/OFF/CON” setting first. 11.2. Press “#” or “*” button to set the desired setting, and the display will update to current setting also, ”LED ON”à” LED OFF”à”LED CON”à ”LED ON”……..to control the handset LED. 11.3. Press “MEMO” key to confirm. After confirmation, It will enter display contrast setting. 12. Setting display contrast CONTRAST 56 12.1.
PAGE 8
Giant -309 Operation Manual (2.4GHz Cordless + CID) Display 12-character text line Descriptions Remarks For display of callers’ name, system prompts (CID Dot-matrix and phone), call timer, dial number. (5 x 5 ) 12-digit number line 1, Display caller’s number (CID), or 7-segment 2, Display dialed digits (phone).
PAGE 9
Giant -309 Operation Manual (2.4GHz Cordless + CID) NEW CALL NEW CALL 2 10:00 AM 1 1/0 1 1 2 3 -- 4 5 6 -- 7 8 9 S M ICALL T H J OHN 13.1.2. The display also indicates if caller information is not available or if the sender intentionally blocks the number. NEW CALL 10:00 PM 1 0/3 0 1 NO CALLER ID NEW CALL 10:00 PM 1 0/3 0 1 CID BLOCKED 13.1.3. After 20 seconds, the display will return to standby mode and shows “NEW CALL XX” where XX is the number of unread calls.
PAGE 10
Giant -309 Operation Manual (2.4GHz Cordless + CID) 13.2.3. If the received call information is same as any of the existing new calls, the ‘RPT’ icon will be on to indicate REPEAT CALL. The most recently arrived CID will be saved attached with a new date / time stamp. The previously arrived record will be deleted. After you review this call, the ‘RPT’ icon will be off. 13.2.4.
PAGE 11
Giant -309 Operation Manual (2.4GHz Cordless + CID) 13.4. DELETE INDIVIDUAL CALL 13.4.1. When you review the call information, you can delete it from the display.Press “#” or “*” button until the call record you want to delete. CALL 10:00 PM 1 0/3 0 1 1 2 3 -- 4 5 6 -- 7 8 9 0 S M ICALL T H J OHN 13.4.2. Press “Del” button, the LCD display “Erase ?”. 13.4.3. Press “Del” button again to confirm deletion. 13.4.4. If the deleted message is last one, it will go back to stand-by mode.
PAGE 12
Giant -309 Operation Manual (2.4GHz Cordless + CID) ring, and VIP icon will be on. 13.6.1. Press “#” or “*” button to select the caller to which you want to assign a VIP. 13.6.2. Press and hold “Calls” button for 2 seconds , the VIP icon is on. 13.6.3. Press and hold “Calls” button for 2 seconds , the VIP icon will disappear as VIP call. * * Press ‘CHANNEL’ button to return to stand-by. No press any button for 20 seconds, it will return stand-by mode. 13.7.
PAGE 13
Giant -309 Operation Manual (2.4GHz Cordless + CID) 13.7.4.2. If a 10 digits long CID number (123-456-7890), the first 3 digits of the number matches local area code, the area code will be skipped and only the last 7 digits will be dialed out in the re-dialing. 4 5 6 7 8 9 0 13.7.4.3. It is also possible to insert an access code ‘1’ in front of 7-digit numbers. Press and release CID “Calls” button twice within 2 seconds to do so. 1 4 5 6 7 8 9 0 * * Press ‘CHANNEL’ button to return to stand-by.
PAGE 14
Giant -309 Operation Manual (2.4GHz Cordless + CID) * No press any button for 20 seconds, it will return stand-by mode. 14. Visual message function When Visual message function is activated, the Telephone Company sends the Visual message information out accordingly. The device receives and displays this information for each Visual message. 14.1. After received Visual message ON, New voice-message Icon will be turned on. NEW CALL 10:00 PM 1 0/3 0 5 CALL 14.2.
PAGE 15
Giant -309 Operation Manual (2.4GHz Cordless + CID) 15.2.2. You enter number, the display will shift entered digits from right to left-hand side until the number reach to 16 digits. If the number is larger than 16 digits, error tone will be generated. Eg.
PAGE 16
Giant -309 Operation Manual (2.4GHz Cordless + CID) 2 3 4 5 6 7 8 9 9 9 9 0 MEM 2 0 1 15.2.3. Press “Del” button to delete the last entered digit. The display will shift entered digits from left to right-hand side. 15.2.4. Press “Flash” button to clear all entered digits. 15.2.5. Press “MEMO” button to save entered number. The display will show ‘LOCATION? X’. LOCATION? X 15.2.6. Press “ MEMO” button to confirm saving number to MEM2 or you press digit button to save number to other indirect memory.
PAGE 17
Giant -309 Operation Manual (2.4GHz Cordless + CID) l No press any button for 20 seconds, it will return stand-by mode. 15.5. Dial indirect memory ( TALK ON ) 15.5.1. Press “TALK” button to enter TALK-ON mode. The display will show ‘TALK 0:00’. 10:00 PM 1 0/3 0 T A LCALL K 0 : 0 0 15.5.2. First, you press “MEMO” button. Second, you press digit button to dial memory. The display will scroll across the screen from right to left-hand side as it is dialed.
PAGE 18
Giant -309 Operation Manual (2.4GHz Cordless + CID) 16.3. Press “Flash” button to clear all entered digits and it will return to stand-by. 16.4. Press “Calls” button, The unit will enter TALK-ON mode automatically. The number will scroll across the screen from right to left-hand side as it is dialed. 16.5. Direct number saves to indirect memory Press “MEMO” button to save last 16 digits of direct number to indirect memory. The unit will assign a free memory.
PAGE 19
Giant -309 Operation Manual (2.4GHz Cordless + CID) - ‘*’ will be displayed as ‘ ’ in line2, ‘*’ in line3 PAUSE will be displayed as ‘P’, when PAUSE is encountered during dialing, a pause of 4 seconds will be generated. 19. Call timer 19.1. The call timer comes up automatically at the line seizes on TALK ON mode and shows on the 3rd line of the display. After 10 seconds the call timer will appear as dialing activities finishing. 10:00 PM 1 0/3 0 T A LCALL K 0 : 0 1 19.2.
PAGE 20
Giant -309 Operation Manual (2.4GHz Cordless + CID) 21. Mute 21.1. Press and hold “Mute” button to mute audio in TALK ON mode. 22. Changing Volume User can adjust the volume levels (3 levels) in talk mode. Pressing “Del” key to increase or “Calls” key to decrease the receiver volume. Volume level doesn’t return to default value when the handset goes back to standby mode. 23. Handset LED If the handset LED is set to ON, the handset LED will be turned on for one minute when the handset is on cradle.
PAGE 21
Giant -309 Operation Manual (2.4GHz Cordless + CID) Consumer Information: This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of this equipment is a label that contains, among other information, a product identifier in the format US:DDKW900BOL2430. If requested, this number must be provided to the telephone company. An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e.
PAGE 22
Giant -309 Operation Manual (2.4GHz Cordless + CID) Industries, with the below information for warranty information. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. QUESTIONS??????? OUR HELP LINE IS 1-866-537-0384 TRANSLATION TABLE Max. length 1. Out of Area 12 NO CALLER I D FUERA AREA HORS ZONE 2. Private Call 12 CI D BLOCKED LLAM PRI VADA APPEL PRI VE 3.