User Guide of Wi-Fi Phone CP300A Giant Electronics Limited Revision 0.1 0.2 0.3 0.4 0.5 0.
TABLE OF CONTENTS 1. SAFETY and IMPORTANT INFORMATION.........................................................................3 2. WELCOME...........................................................................................................................3 3. GETTING STARTED ............................................................................................................4 3.1 Conventions Used in this User Guide.........................................................................4 3.
1. SAFETY and IMPORTANT INFORMATION NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
CP300A can connect to your wireless router or access point to receive telephone service through your cable or DSL Internet connection. Note: For information about your Internet phone service, refer to the materials provided by your Internet phone service provider. 3. GETTING STARTED 3.1 Conventions Used in this User Guide 3.2 Package Content Please check the package contents by comparing them with the following list. - 1 x Model CP300A - 1 x Rechargeable battery - 1 x Charging Cradle - 1 x adapter 3.
• 2 way charging (Direct pug with adapter or charging through cradle) 3.
^: Speaker, handsfree, handset volume up V: Speaker, handsfree, handset volume down ●: Function same as left soft button Side Panel - TBC Back Panel - TBC Bottom Panel - TBC 3.5 Display Description Please refer to the table below for a list of icons that appear on the home screen and their meanings. Signal Strength: Indicates the signal strength of the access point you’re IP Phone is connected to. Mute icon Vibration is on.
4 5 6 7 Plug the power cord into the corresponding jack on the bottom of the handset or place the handset in the charging cradle properly. Connect the power supply to a live outlet. Leave the Handset for 15 hours so that the battery pack is fully charged. The battery icon will flash during charging. While the battery is fully charged, it stops flashing. 4. BASIC OPERATION 4.1 Switch the Phone On/Off Press and hold the [END] key for 2 seconds to turn the Phone on or off.
18. Input the Registrar port of your Internet phone service provider’s account. 19. Input the OB proxy (Outbound Proxy) of your Internet phone service provider’s account. 20. Input the OB proxy (Outbound Proxy) of your Internet phone service provider’s account. 21. Input the OB proxy port of your Internet phone service provider’s account. 22. Easy setup finished. 4.
• After mute the call, press [Left-Soft-Key] to open More. Select Speaker off to turn off the speaker function. 4.8 Dial a New Call There are 2 ways to dial a new call while on a call. Dial a New Call from [Left-Soft-Key] 1. While on a call, if you need to connect to a third party, press the [Left-Soft-Key] to open More. 2. Select Dial new call and input the new phone number of third party. 3. Press [SEND] key to dial the new phone number, 4.
Call Swap 1. While holding two calls, press [Up] or [Down] key to select the active call (the call with active call icon ), then press [Left-Soft-Key] to open More. 2. Select Swap. 3. The call originally placed on hold would be swapped to be active call and the active call would be swapped to be placed on hold. Note: You can also active swap function by selecting the call placed on hold. 4.10 Redial 1. In home screen, press [SEND] key to enter Dialed Calls. The dialed numbers are shown. 2.
5.2 Call History 2. Call History Missed Calls Saved as new Add to contact View Details Remove Remove All Received Calls Saved as new Add to contact View Details Remove Remove All Dialed Calls Saved as new Add to contact View Details Remove Remove All 5.3 Call Features 3. Call Features Call Forward All Calls Forward Add. Enable Yes No On busy Forward Add. Enable Yes No On No-Answer Forward Add.
Yes No Direct IP 5.3.1 Call Forward User can set their preference according to 5.3 chart (to enable/disable, forward situation and time out duration, etc.) 5.3.2 Speed Dial The Speed Dial menu allows you to assign up to nine phone numbers you frequently call to the number keys on the phone. Follow the steps below to assign a contact to your Speed Dial list. 1. If necessary, press [Left-Soft-key] in home screen to enter MENU ( Call Features ( Speed Dial. 2.
120 ms 140 ms VAD Enable Disable CNG Enable Disable DTMF Gen In-Band DTMF RFC2833 Both Ringer Ringtone Ringtone 1 Ringtone 2 Ringtone 3 Volume Lever 1 to 10 Vibration On Off Auto Keylock On Off Date/Time NTP NTP Svr Add Enable Yes No Time Zone GMT -12:00, GMT -11:00, GMT -10:00, GMT -09:00, GMT -08:00, GMT -07:00, GMT -06:00, GMT -05:00, GMT -04:00, GMT -03:30, GMT -03:00, GMT -02:00, GMT -01:00, GMT 0:00, GMT +01:00, GMT +02:00, GMT +03:00, GMT +03:30, GMT +04:00, GMT +04:30, GMT +05:00, GMT +05:30, GMT +0
5.5 Admin. Configuration 5. Admin Conf WLAN Conf Current Conf Config 1 Config 2 Config 3 Config 1 SSID Mode Infra AdHoc Encryption Mode None WEP WPA Personal WEP Keys WEP Bits 64 128 Def Key ID WEP Key 1 WEP Key 2 WEP Key 3 WEP Key 4 WEP Key 1 WEP Key 2 WEP Key 3 WEP Key 4 WPA Personal Passphrase TCP/IP IP Info.
Ob Proxy Port User 2 (same as User 1) Others Easy Setup Restore preset FM Upgrade HTTP server Upgrade Diagnostics Ping Ping Dest. Traceroute Tracert Dest.
