System Recovery Use System Recovery when: Your Windows operating system does not start at all. You want to restore the system to the factory state. WARNING: Using this feature will reinstall Windows to your system and configure it to the system’s factory default settings. All data on the hard disk drive will be lost. Make sure that power is not interrupted during the recovery process. An unsuccessful recovery may result in Windows startup problems. To run System Recovery: 1.
4. The progress bar shows the percentage completed. When it reaches 100%, the system turns off. 5. Turn on the computer. The Windows setup wizard starts. Follow the onscreen prompts to continue. 6. When the system restarts, the installer screen appears. The installer will perform system hardware detection and driver installation.
7. When completed, the system restarts and displays Windows desktop.
Chapter 6 Using Getac Software Getac software includes application programs for specific computer components and utility programs for overall management. This chapter describes how to use the software.
Using the OSD Control Panel The OSD (On Screen Display) Control Panel provides a user-friendly interface for you to quickly activate or operate certain functions on your computer with a simple tap of the screen. To open the OSD Control Panel, press the button The following screen appears. on the front of your computer. The following table shows the various functions on the OSD Control Panel. Icon Function Opens the Help file explaining the OSD Control Panel.
Icon Function Serves as the master ON/OFF control of the RF radio. The word on the button indicates the current status. The on/off status will persist through Sleep/Hibernation mode but it will always be on upon restarting. Enables or disables the G-Rotate function. When enabled, the LCD display will rotate itself to match the direction the computer is held. This button is available for use only when the computer is in Tablet mode.
Icon Function When set to MAX, MAX the backlight is adjusted to the highest brightness level. When set to AUTO, AUTO the brightness will be automatically adjusted according to the current ambient light. The backlight will return to the default MANUAL setting whenever the system resumes from Sleep/Hibernation mode or the system is restarted. Switches the display output to the next choice: VGA (external monitor), BOTH (LCD and external monitor), or LCD.
Icon Function Allows you to adjust the sound volume by dragging the knob along the bar. Switches the system sound output OFF (mute) and ON. Allows you to adjust the LCD brightness level by dragging the knob along the bar. System enters “black-out” mode by turning off the LCD display, LED indicators, touchscreen, and sound. Press the power button ( “black-out” mode.
Quick Button Setup By default, the five quick buttons on the OSD Control Panel have pre-assigned functions. You can re-define the buttons: 1. Click the Quick Button Setup button ( the Quick Button Setup Setup window appears. ) on the OSD control panel and 2. At the bottom of the screen are the five quick buttons. Click the button you want to change. 3. Depending on the type of task to be associated with the button, click the Open button of the Executed Program or Open Folder type. 4.
or 5. You can change the image appearing on the button by clicking the Select Image button. After selecting the image file, the original image on the button will be replaced. 6. Click Set to complete the changes. NOTE: You can restore the quick buttons to the default settings by clicking Reset All.
Using Button Manager The five quick buttons located on the front of your computer come with predefined functions. You can use Button Manager to re-define the buttons. 1. Click Start Programs screen appears. Button Manager Button Manager. Manager The following ġ 2. Select the button to re-define. 3. Under the Update Update Button Function click the Key Name dropdown list to see the available options and select the option you want.
The option User Define Button (1 to 5) means the Quick Button in the OSC Control Panel. 4. Repeat the steps for the other buttons that you want to re-define. 5. For the changes to take effect immediately, click Start Flash. 6. If you intend to save the configurations for later retrieval, click SAVE. Select a location, enter a filename, and click Save to save the current configurations as a .bfh file. Click Load the next time you use Button Manager to load any previously saved configurations.
Using GG-Manager G-Manager is a unified user interface utility that allows you to manage and configure the following: System Battery ECO (economic mode) Light Sensor Ignition Monitoring GPS Status Starting GG-Manager You can start up G-Manager by any of the following methods: All Programs Getac Utility G-Manager, or Click Start Click and hold the icon located on the taskbar until a ring appears. From the small menu that pops up, click G-Manager Manager.
System Tab The System tab provides system information. To view specific information, select the component from the list on the left side of the screen. The information of the selected component will be displayed on the right side of the screen.
Battery Tab The Battery tab allows you to check the battery status and configure the battery. At most two batteries may be supported. Click Battery 1 or Battery 2 to view the information of each battery (if your model has a second battery). NOTE: When the percentage % Left is less than 10% then the value will be displayed in red. When an abnormal battery condition is detected Battery Status value will be displayed in red.
Charging Mode The lower left portion of the screen allows you to select the charging mode. Normal Mode – The battery will be fully charged. When remaining charge reaches below 95%, then charging will start until it is fully charged. Economy Mode – This mode helps prolong battery life by charging up to 80% of its total capacity only. It is highly recommended if you are using AC power most of the time.
4. Wait till the process is completed. Click Exit when finished. ECO Tab The ECO tab allows you to configure ECO modes (or called power profiles).
To put the system into an ECO mode, use the ECO button (one of the buttons in the OSD Control Panel). (See “Using the OSD Control Panel” earlier in this chapter for information.) ECO Information The left portion of the screen lists the available power profiles (Quick, Power Saving, and Work). Each profile is a combination of power settings that results in different power consumptions. To change the settings of a profile, select (highlight) the profile name in the list.
Power Scheme – can be Balanced, High Performance or Power Saver. The settings here correspond to the settings in Windows. (See Windows Help for the description to each of the power scheme.) After changing the settings, click Apply or OK to save the changes. To restore the settings to the default values, click Default. Light Sensor Tab The Light Sensor tab allows you configure how the light sensor works.
Sensor Mode The left portion of the screen lists the sensor modes: Normal – Light sensor sensitivity is set at normal environment lighting condition. Bright – Light sensor sensitivity is set at bright environment lighting condition (e.g. outdoors). Dark – Light sensor sensitivity is set at dark environment lighting condition (e.g. indoors, storage warehouse, etc.). Click to select a mode. Click Apply or OK to save the changes.
Ignition Tab The Ignition tab allows you to configure how your system works with the vehicle ignition. Ignition Control When your system is connected to the Vehicle Dock (available as an option), you can have your system derive power from the vehicle and have the on/off of the vehicle ignition turn on/off your system. To enable the feature, select the checkbox Ignition Power On. On Click Apply or OK to save the changes.
Monitoring Tab The Monitoring tab allows you to configure the monitoring function of G-Manager. Items to Monitor The left portion of the screen lists the items. Click the checkbox before an item to include it as a monitored component. Click Apply or OK to save the changes. NOTE: Different models have different supported monitoring items; non-supported items cannot be selected (grayed out items).
Monitoring Interval – sets the frequency of updates on the monitoring window (1/3/5/10/30 seconds or 1/5/30 minutes). Click Apply or OK to save the changes. Starting and Stopping the Monitoring To start monitoring, click START Monitor. Monitor The monitoring window similar to the one below appears displaying requested information at specified intervals.
To start GPS positioning, click Start GPS. GPS The screen displays: Ongoing raw data strings in the Message Log section Overhead satellite positions in the Satellite Map section Signal strength of the satellites in the Signal Indicator section When GPS positioning is completed, the Data Summary section shows the GPS information of the current location. To stop GPS positioning, click Stop GPS.
Using Getac Camera Getac Camera is a geo-tagging camera program, which allows you to stamp geographical information on photos as watermarks and embed such information into JPEG files as EXIF 2.2 metadata. NOTE: Getac Camera works with Virtual-GPS (a separate application program). Make sure that Virtual-GPS is installed in your computer. Before starting Getac Camera, close any other program that uses the camera; otherwise, Getac Camera can only provide limited functions.
No. Screen Elements Descriptions Preview/Display Window Displays the live image in Camera mode and the selected image in View mode. Status Display Indicates the use of a feature. GPS Lock in use Front/Bottom camera in use (depending on your model) / Night mode in use Continuous/Timer mode in use / GPS Status Indicates if the GPS positioning is completed ( ). not ( Window Control Buttons ) or Minimizes the program window. Closes the program.
Switches to View Mode. Switches to GPS view. Switches to the Settings screen. No. Screen Elements Descriptions Provides copyright, licensing, and help information. Taking Pictures 1. Start the Getac Camera program. You will be in Camera Mode. 2. You can use the buttons on the right and left side of the preview window for immediate controls. (See “Camera Controls Buttons” for detailed information.) For overall settings, tap . (See “Camera Settings” for detailed information.) 3.
4. When ready, you can shoot the picture in either of the two methods: Method 1: Tap the button. Method 2: Drag the preview image and drop it into Thumbnail Tray. 5. The picture will appear in the middle of the Thumbnail View and be saved to the predefined storage location. Camera Controls Buttons Control Buttons Descriptions Descriptions Flips the image vertically. Flips the image horizontally. / Turns on/off GPS lock. The icon in the button shows the current status.
/ Turns off/on watermark. The icon in the button shows the current status. You can turn off watermark if you do not want the watermark to show in the picture. Your setting remains effective until you change it again. Shooting Videos 1. Start the Getac Camera program. You will be in Camera mode. Tap to switch to Camcorder mode. 2. You can use the buttons on the right and left side of the preview window for immediate controls. (See “Camcorder Control Buttons” for detailed information.
4. To stop, tap the same button again. 5. An image from the video will appear in the middle of the Thumbnail Tray. The file is saved to the predefined storage location. Camcorder Control Buttons Control Buttons Descriptions Descriptions Increases the recording sound volume. / Disables/enables the microphone. Decreases the recording sound volume. Flips the image vertically. / Turns on/off the display of elapsed recording time and current volume.
Selecting an Image or Video To scroll through the Thumbnail Tray, drag the tray toward the left or right. To select an image or video, use either of the two methods: Method 1: Double-tap the thumbnail in the Thumbnail Tray. Method 2: Drag the thumbnail and drop into the display window.
When you select an image to view, you can perform the following tasks. To Via Control Buttons Zoom in/out (up to four scales) Via MultiMulti-touch Operations / Drag two fingers apart/ towards to zoom in/out. To Via Control Buttons Via MultiMulti-touch Operations When zoomed in, you can drag to view another portion of the image. − Restore to the 100% scale Rotate to the right/left by 90° / Drag two fingers in a clockwise/counterclockwise circular motion.
3. Type your notes in the entry field. 4. When completed, tap . The first three lines of the notes show on the screen. Video Playback Controls When you select a video to playback, you can perform the following tasks.
Turn on/off the status display / Camera Settings To change camera settings, tap at the bottom of the screen. Along the left of the window are all the setting items. You can drag this area up or down to scroll through the items. The middle of the window displays the current item and setting value. To the right is the adjustment bar where you can tap or drag to change the setting value. All changes (except for Camera Mode) remain effective until you change them again.
Items Name Descriptions Descriptions White Balance Five choices from which you can select one that matches the current light source: Automatic (default), Sunshine, Cloudy, Fluorescence, and Incandescence. Brightness Adjusts the brightness level. The range of levels depends on computer models. to restore to the default level. You can tap Items Name Descriptions Contrast Adjusts the contrast level. The range of levels depends on computer models. You can tap to restore to the default level.
Camera Mode Three choices for the shooting mode: Status Display Items Normal This is the default setting whenever the program is started. Continuous Continuous shooting of 3 pictures (one shot per second). Timer 5-second countdown before shooting. Turns On (default) or Off the display of the status indicators. Name Descriptions Watermark Turns On (default) or Off the display of watermark in the image. (Turning off does not affect the embedded EXIF 2.2 metadata.
The default location is Users\[user name]\Pictures folder that contains the original images. A subfolder named Thumbs contains a copy of the same images (with filename prefix Thumb_) for the thumbnail view. NOTE: If you are adding or deleting images using File Explorer, make sure to work on both the correct folder and its Thumbs subfolder.
Chapter 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering areas such as protecting, storing, cleaning, and traveling.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using an AntiAnti-Virus Strategy You can install a virus-detecting program to monitor potential viruses that could damage your files.
Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock. Store the key in a safe place.
Taking Care of the Computer Location Location Guidelines For optimal performance, use the computer where the recommended temperature is between 0°C (32°F) and 55°C (131°F) – actual operating temperature depending on product specifications. Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust.
General Guidelines Do not place heavy objects on top of the computer when it is closed as this may damage the display. The screen surface is easily scratched. Avoid touching it with a sharp object such as a pen or pencil. To maximize the life of the backlight in the display, allow the backlight to automatically turn off as a result of power management. Avoid using a screen saver or other software that prevents the power management from working.
Battery Pack Guidelines Recharge the battery pack when it is nearly discharged. When recharging, make sure that the battery pack is fully charged. Doing so may avoid harm to the battery pack.
– avoid installing or removing the battery pack when the computer is in Sleep mode. Abruptly removing the battery pack may cause loss of data or the computer may become unstable. – avoid touching the battery pack terminals or damage may occur, thereby causing improper operation to it or the computer. The computer’s input voltage and surrounding temperature will directly affect the battery pack’s charge and discharge time: – charging time will be prolonged when the computer is turned on.
Do not use excessive force on the display. Avoid moving the computer while holding the display or twisting the display. Avoid placing objects on top of the display as this may cause the glass to break thereby damaging the display. Using the touchscreen during low temperature (less than 5oC) may cause a slower response time, this is normal. A normal response time may be restored upon returning to room temperature.
When Tr Traveling aveling Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure that the battery pack is fully charged. Make sure that the computer is turned off and the top cover is securely closed. Do not leave objects in between the keyboard and closed display. Disconnect the AC adapter from the computer and take it with you.
Chapter 8 Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the BIOS Setup program.
Solving Common Problems Battery Problems The battery does not charge (Battery Charge indicator does not light yellow). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
Display Problems Nothing appears on the screen. During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. The brightness level might be too low. Increase brightness. The display output might be set to an external device. To switch the display back to the LCD, press the Fn+F5 hot key or change the display through the settings in Display Properties. The characters on the screen are dim.
Simultaneous display/multi-display does not work. Make sure that you turn on the external monitor before turning on the computer. Press the Fn+F5 hot key to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device. The device may not be correctly configured in the BIOS Setup program. Run the BIOS Setup program to identify the new type.
Keyboard, Mouse, and Touchpad Problems The keyboard does not respond. Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. Water or liquid is spilt into the keyboard. Immediately turn off the computer and unplug the AC adapter. Then turn the keyboard upside down to drain the liquid out of the keyboard. Make sure to clean up any part of the spill you can get to.
Modem Problems The modem does not work. Make sure that the modem driver is correctly installed. Make sure that the telephone line is properly connected. Make sure that the COM port in the communication software is correctly set. Turn off power management. Power Management Problems The computer does not enter Sleep or Hibernation mode automatically. If you have a connection to another computer, the computer does not enter Sleep or Hibernation mode if the connection is actively in use.
Software Problems An application program does not work correctly. Make sure that the software is correctly installed. If an error message appears on the screen, consult the software program’s documentation for further information. If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced. Make sure that the volume control is not set too low. Make sure that the audio driver is correctly installed.
Check the volume control of your computer. Startup Problems When you turn on the computer, it does not seem to respond. Make sure that either the AC adapter is connected or the battery has power. For models with the HDD heater option: When turning on the computer in an extremely low temperature environment, the computer will heat up the hard disk before starting up. The hard disk drive in-use indicator blinks red to indicate the heater is on.
Check if there is high interference around the environment and solve the problem as described next. Radio interference exists. Move your computer away from the device causing the radio interference such as microwave oven and large metal objects. Plug your computer into an outlet on a different branch circuit from that used by the affecting device. Consult your dealer or an experienced radio technician for help. I cannot connect to another WLAN device.
Reconfigure and reset the Access Point. I cannot access the network. Make sure that the necessary driver(s) is correctly installed. Make sure that the network configuration is appropriate. Make sure that the user name or password is correct. You have moved out of range of the network. Turn off power management. Other Problems The date/time is incorrect. Correct the date and time via the operating system or BIOS Setup program.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
Appendix A Specifications NOTE: Specifications are subject to change without any prior notice. Parts Specifications CPU Intel® Ivy Bridge i5-3320M, 2.6G, 35W Chipset Intel® Panther Point QM77 Memory Up to 8 GB, 240-pin × 2, DDRIII 1333MHz SO-DIMM BIOS 8 MB EEPROM, system and VGA BIOS, Plug-and-Play, ACPI 2.0 capability Display Audio Panel 12.
Parts Specifications Memory card reader SD/SDHC/SDXC I/O ports USB 3.0 x 2, USB 2.0, Mini 1394a, serial (RS-232), RJ-45, RJ-11, headphone out, microphone, VGA, docking (100-pin) Antenna Wi-Fi 802.11a/b/g/n + Bluetooth 2.4G 2 internal (pass-through for external antenna – option) WCDMA/HSDPA 2 internal (pass-through for external antenna – option) GPS 1.5G (option) 1 internal Modem Azalia interface, 56 Kbps, ITU V.90 MDC 1.5 internal fax modem LAN IEEE 802.3i 10Base-T, IEEE 802.
Parts Environment Environment Specifications Temperature 0 °C (32 °F) to 60 °C (140 °F) -20 °C (-4 °F) to 60 °C (140 °F) – low temperature option Non-operating: -51 °C (-60 °F) to 71 °C (160 °F) Humidity 5 % to 95 % relative, non-condensing Altitude Operating: 15,000 ft Non-operating: 40,000 ft Shock Operating: 40 g, 11 ms, sawtooth pulse Vibration Integrity: Operating: Vehicle: Regulation MIL-STD-810G, Method 514.6, E-1, Category 24, minimum integrity MIL-STD-810G, Method 514.
Appendix B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. − − Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ.
that will reduce cooling. Do not use the AC adapter while it is inside a carrying case. Connect the adapter to a proper power source. The voltage requirements are found on the product case and/or packaging. Do not use the adapter if the cord becomes damaged. Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. About the Modem Caution Never install telephone wiring during a lightning storm.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC. Swedish Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC. Local Restrictions of 802.
General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “Turning Off the Wireless LAN Radio”.
Departments in Which the Wireless LAN Module’s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
