A790 Operation Manual Part Number: 7990 0114 3001 R00 (July 2006)
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Table of Contents Preface ......................................................................................vii Chapter 1 Getting Started......................................................1-1 Getting the Computer Running..............................................1-2 Unpacking .......................................................................1-2 Connecting to AC Power .................................................1-2 Opening the Cover ........................................................
Euro Symbol ...................................................................2-6 Windows Keys ................................................................2-6 Function Keys .................................................................2-6 Fn Key.............................................................................2-7 Hot Keys..........................................................................2-7 Using the Touchpad ..............................................................
Chapter 4 Expanding Your Computer ..................................4-1 Connecting an External Monitor............................................4-2 Connecting a Parallel Device.................................................4-3 Connecting a Serial Device ...................................................4-4 Connecting an IR Device ......................................................4-5 Connecting a USB Device .....................................................4-7 Connecting an IEEE 1394b Device ....
Location Guidelines.........................................................7-3 General Guidelines ..........................................................7-3 Cleaning Guidelines.........................................................7-4 Battery Pack Guidelines ...................................................7-4 When Traveling ....................................................................7-5 Chapter 8 Troubleshooting ...................................................8-1 Preliminary Checklist..
USA and Canada Safety Requirements and Notices ........ B-6 European Union CE Marking and Compliance Notices ...
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and 2 appendices. l Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. l Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. l Chapter 3, Managing Power, provides information on power.
l Appendix B, Regulatory Information, provides regulatory statements and safety notices on your computer. Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
CHAPTER 1 Getting Started Congratulations on purchasing this computer. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: l Notebook computer l Accessories: − AC adapter (100~240 VAC, 50/60 Hz) − AC power cord (US/CE/UK/SA) − Driver CD − This Operation Manual Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. l When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover CAUTION: Be gentle when opening and closing the cover.
Turning On and Off the Computer Turning On 1. Make sure the computer is connected to AC power. 2. Press the power button. 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this manual. Right-Side Components Ref Component Description See Also Œ PC Card Slot Accepts a PC card for additional functions.
Left-Side Components Ref Component Description Œ Bay2 Slot May contain an extra battery pack or wireless modem (GPRS/GSM, CDMA) module. • Battery Pack Supplies power to your computer when external power is not connected. Getting Started See Also P.
Rear Components Ref Component Description See Also Œ Power Connector Connects the AC adapter. P. 1-3 • USB Ports Each of the two ports connects a USB device, such as a USB floppy drive, USB flash disk, printer, digital camera, joystick, and more. P. 4-7 Ž Docking Port For connecting to a Port Replicator / car mount (both are available as an option). • RJ-45 Connector Connects the LAN cable. Includes a Link Indicator and an Active Indicator.
Ref • Component Description See Also Serial Port Connects a serial device, such as an external modem. P. 4-4 Kensington Lock Locks the computer to a stationary object for security. P. 7-2 IR Port Connects an IrDA-compliant device for wireless data transfer. P.
Front Components Ref Component Description Œ Top Cover Latch Locks the top cover. • Stereo Speaker Set Sends out sound and voice from the computer. Ž Handle Allows you to carry your computer for an easy grip. 1-10 See Also P. 1-4 P.
Top-open Components Ref Œ Component LCD Screen Getting Started Description Displays the output of the computer. Can also have the optional touchscreen function. See Also P. 2-17 P.
Ref • Component Device Indicators Description See Also Show the current status of the computer’ s devices. Scroll Lock indicator P. 2-4 A Caps Lock indicator P. 2-4 N Num Lock indicator P. 2-6 Hard disk drive in-use indicator P. 2-14 Battery charge indicator – Glows green when the battery is fully charged and connected to AC power. Glows amber (orange) when the battery is being charged. P. 3-3 Battery power indicator – Glows green when the computer is using battery power.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… Do this… To know more about the computer… Go on to the next chapter. To install the operating system if your dealer has not already done so… See the operating system manual. To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
1-14 Getting Started
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a CD disc if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode… Do this… To start up or resume again Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover. • Pressing Fn+F12 • Pressing the power button Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard NOTE: Your computer features backlight for your keyboard to help you see the keyboard keys during poor lighting conditions. Press Fn+F8 to turn it on/off (see Hot Keys later in this chapter). Your special shower-proof and dust-proof rubber keyboard has all the standard functions of a full-sized computer keyboard plus an Fn key added for specific functions.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. l Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.
Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way.
Key Description Switches the display output to one of the following when an external device is connected. Upon booting the system with CRT: LCD LCD & CRT CRT Upon booting the system with DVI: LCD LCD & DVI DVI NOTE: l When in full screen DOS mode, or when playing DVD or MPEG file, display switching is not allowed. l If the display mode is set to 256 colors or lower, or in DOS mode, there will be only two modes for selecting: CRT only and LCD & CRT. l This function only applies to Plug & Play CRT monitors.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Doubleclick Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver if you are using Windows to take advantage of more powerful features.
Using the Touchscreen (Optional) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons. The touchscreen needs a special device driver support that allows you to easily use the computer without a mouse or touchpad (see chapter 6 for details).
Term Action Drag and drop Press lightly on the touchscreen and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location. Scroll To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger on the right edge of the touchscreen and slide your finger up and down along the edge.
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive that features a built-in G-sensor to prevent damage during an accidental drop.
4. Remove the two screws securing the hard disk drive compartment. 5. Lift up the handle and pull on it to remove the hard disk drive compartment. 6. Remove the two screws securing the hard disk drive to the compartment and remove the steel plate cover.
7. Lift up the hard disk drive from the compartment and replace it with a new one. 8. Replace the steel plate cover and replace the two screws to secure the hard disk drive to the compartment. 9. Replace the hard disk drive compartment to the computer and secure with two screws. 10. Replace the battery pack.
Using the Video Features The video subsystem of your computer features: l 12.1/14.1-inch TFT (Thin-Film Transistor) color LCD display with 1024×768 XGA (eXtended Graphics Array) resolution, or optional 14.1-inch TFT (Thin-Film Transistor) color LCD display with 1400×1050 SXGA+ / SXGA (Super eXtended Graphics Array) resolution l 64 MB video memory shared with system memory l LCD backlight to help you see the display during poor lighting conditions.
For displaying in higher resolutions, you can connect an external CRT monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.) The following table lists the display modes supported by your computer.
Using the Audio Features NOTE: l To take advantage of the enhanced audio capabilities, the device driver supplied with your computer must be installed (see chapter 6 for details). l If you experience interference while recording, try lowering the microphone recording volume. The audio subsystem of your computer features: l External audio connectors (Œ) and l A set of speakers (•) Ways of playing and recording sound vary with the operating system used.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. l Audio Output Connector ( ) can be connected to the line-in connector of powered speakers with built-in amplifiers, headphones, or earphone set. l ) can be connected to an external Microphone Connector ( microphone for recording voice or sound. NOTE: When using external speakers/headphones or microphone, you cannot use the internal one.
Using the Communication Features Using the LAN NOTE: To take advantage of the LAN feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 10/100/1000Base-T Ethernet LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN (Optional) Depending on your model, an internal Mini PCI wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: l Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support l WEP (Wired Equivalent Privacy) 64/128-bit data encryption l IEEE 802.11a/b/g standard compliance Technology 802.11a 802.11b 802.
Configuring the WLAN After driver installation, you can use the WLAN utility to configure and monitor your WLAN connection. If you are using Windows XP, you can also use its built-in WLAN utility. Follow this procedure to launch the WLAN utility in Windows XP: 1. Select Control Panel from the Start menu. 2. Click Network and Internet Connections. 3. Click Network Connections, then double-click the Wireless Network . Connection icon 4. Click Properties in the Wireless Network Connection Status dialog box. 5.
4. If any wireless network is detected, the following window appears on screen. 5. Click to select a wireless network to connect to, and then click Connect. 6. Depending on the settings, you may be asked to enter a wireless security password (encryption key). For more information on the Intel PROSet Wireless utility, click Help? in the Intel(R) PROSet/Wireless window. It takes approximately 30 seconds for your computer to make a successful WLAN connection and approximately 10 seconds to disconnect.
Using the Modem NOTE: To take advantage of the modem feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
Using the Wireless Modem (Optional) NOTE: To take advantage of the wireless modem feature, the USB-to-COM driver supplied with your computer must be installed (see chapter 6 for details). Depending on your model, your computer includes an integrated GSM (Global System for Mobile Communications) / GPRS (General Packet Radio Service) feature. After you establish a subscription with a GSM/GPRS service provider, you can use the wireless data features of your computer.
Connecting Using GPRS Your computer can receive General Packet Radio Services (GPRS), a high-speed data-only service that transmits data over a mobile telephone network. In addition, GPRS provides permanent on-line connection. To use GPRS, you must have a subscription to the function with a service provider that supports GPRS. To connect to a GPRS network, you must configure a connection for that service on your computer.
Using the Bluetooth Feature (Optional) NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with your computer must be installed (see chapter 6 for details). Depending on your model, your computer may incorporate the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection. With Bluetooth, data can be transmitted through walls, pockets and briefcases as long as two devices are within range.
2. Double-click the icon, then click on New Connection or click on Bluetooth, then Add New Connection . . . Or right-click the icon, and then click on Add New Connection. or 3. The Add New Connection Wizard window appears. Select Express Mode (Recommended), then click on Next.
4. Select the device to connect to and click on Next. 5. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information.
Sending a File 1. Right-click the icon, and then click Wireless File Transfer. The following screen appears. 2. In the Wireless File Transfer window, click Add to browse for the file to send. The file(s) will show on the File/Folder window. 3. Click the target device from the Transfer-enabled device window, and then click Send to start the transfer procedure.
For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help on your computer by clicking on Help, then Help . . .
CHAPTER 3 Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: l The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. l The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The Li-ion battery pack is the internal power source for the computer when the AC power is “Off” or not connected. It is rechargeable using the AC adapter. The removable battery pack, with on-line charge capacity, comes standard with your computer. It has 107 watt operating capacity. The computer supports up to three Li-ion battery packs: Primary, Bay1, and Bay2 (Bay1 and Bay2 are optional). The operating time of a fully charged battery pack depends on how you are using the computer.
The charging times are as follows: Charging Time Battery Type (2400 mah or more per cell) Computer is Off Computer is On and in Idle State Primary (107 watt) 3.5 hours 4.7 hours Bay1 (71 watt) 2.5 hours 3.5 hours Bay2 (71 watt) 2.5 hours 3.5 hours CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery.
Checking the Battery Level NOTE: Any battery level indication is an estimated result. The actual operating time can be different from the estimated time, depending on how you are using the computer. You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the icon on the taskbar. (Click the icon if the computer is using AC power.
4. Lift up the handle and pull on it to slide the battery pack off the computer. 5. Slide the front panel off the battery pack and replace it on a new battery pack. 6. Slide the new battery pack into the computer. 7. Replace the two screws to secure the battery pack on the computer.
Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10 % (Windows default setting) of its charge remaining. The computer gives warning ) blinks amber beeps or messages and the Battery Power Indicator ( (orange) to alert you to take actions. NOTE: You can set up your threshold and signals of Battery Low under Windows. Immediately save your data upon Battery Low. The remaining operating time depends on how you are using the computer.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the system can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. 3-10 l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level. l If you work with an application that uses a PC card, exit the application when you finish using it. l If you have a PC card installed, remove it when not in use. Some PC cards drain power even while they are inactive.
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA port. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a Parallel Device Your computer has a parallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port. Follow this procedure to connect a parallel device: 1. Make sure the computer is not turned on. 2. Plug the parallel device’s cable to the parallel port on the rear of the computer. 3.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as a serial mouse or modem. Follow this procedure to connect a serial device: 1. Make sure the computer is not turned on. 2. Plug the device cable to the serial port on the rear of the computer. 3. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer. Instead, use a modem that is powered by its own internal battery or external AC power.
Connecting an IR Device Your computer has an IR (infrared) port for connecting an infraredequipped device wirelessly such as another computer, printer, or PDA (Personal Digital Assistant). When using the IR port of your computer to receive data: Place the transmitting device where its IR port faces the IR port of your computer within the effective range − within ±20-degrees vertical angle and within ±20-degrees horizontal angle at no greater than 0.8~1.0 meter distance.
NOTE: During infrared communication, note the following: l Do not move the computer and IR device. l Do not enter Standby mode. l Do not use a cell phone or another IR device near the computer. l Avoid strong light such as sunlight or fluorescent light. l Disable the screen saver.
Connecting a USB Device Your computer has two USB ports that supports transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer.
Connecting an IEEE 1394B Device NOTE: l Your IEEE 1394B port will only function under Windows XP SP2. It is also Windows Vista ready. l Make sure that the 1394B driver is installed correctly (see chapter 6 for details). l To connect an IEEE 1394A (also known as FireWire 400) device to the computer’s IEEE 1394B (also known as FireWire 800) port, you need an optional FireWire 800/FireWire 400 bilingual cable. Your computer has an IEEE 1394B port for connecting IEEE 1394B devices.
Using PC Cards Your computer has a PC card slot. PC cards are credit card-sized peripheral products based on the standards developed by PCMCIA (Personal Computer Memory Card International Association). PCMCIA is a non-profit association for promoting the interchangeability among mobile computers where ruggedness, low power, and small size are critical.
To insert a PC card: 1. Locate the PC card slot on the right side of the computer. 2. Slide the PC card, with its label facing up, into the slot until the eject button pops out. Eject Button 3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: icon on the taskbar and 1. Double-click the Safely Remove Hardware the Safely Remove Hardware window appears on screen. 2.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 2 GB on the two 200-pin DDR2 SO-DIMM slots. However, to avoid damage during the installation procedure, please ask your dealer for help.
4-12 Expanding Your Computer
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory default settings. l You want to modify some specific settings according to the hardware. l You want to modify some specific settings to optimize system performance. Starting SCU NOTE: l The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
The SCU menu can be divided into four areas: l On the top is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. l The center column of the menu displays the current configuration information of the system, devices, and memory items. l The right column of the menu provides more detailed information when a menu item is highlighted. l On the bottom keyboard keys are displayed for navigating the screen.
Moving Around and Making Selections In most cases, you must go through two levels to complete the setting for an item: menu title and submenu. Use the keyboard to move around and make selections. A brief description of keyboard usage is listed next: Key 5-4 Function ←,→ Selects a menu title. ↑,↓ Selects an item or option. +, – Changes the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the option window when an item is selected. Esc 1) Displays the Exit menu.
Main Menu The Main menu contains the system date and time as well as the IDE/SATA interface setting of the system. System Time sets the system time. System Date sets the system date. IDE Channel 0 Master/Slave / SATA Port 0/1 sets the type of storage device installed. The options are User, Auto, CD-ROM, ATAPI Removable, None, IDE Removable, and Other ATAPI.
Advanced Menu The Advanced menu contains the hard disk drive heater as well as the screen display setting during system boot-up. HDD Heater sets if the system automatically turns on the built-in hard disk drive heater for low temperature operation. The options are Enabled and Disabled. NOTE: Disable this item to conserve energy when using battery power. Summary Screen sets if the system configuration would be displayed onscreen during system boot-up. The options are Enabled and Disabled.
Intel Menu The Intel menu contains the LPC I/O devices and CPU thermal setting of the system. LPC Control Sub-Menu sets the items that control the configuration of various LPC input/output devices that exists on the CRB as well as the National 393 serial input/output devices. CPU Thermal Control Sub-Menu sets the items that control various CPU thermal parameters.
Security Menu The Security menu contains the security setting, which safeguard your system against unauthorized use. TPM Support enables or disables TPM (Trusted Platform Module) support. The options are Enabled and Disabled. NOTE: To use the TPM feature, the TPM driver supplied with your computer must be installed (see chapter 6 for details).
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a boot device from which to load the operating system. A brief description of keyboard usage is listed next: Key Function ↑,↓ Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence.
Exit Menu The Exit menu displays ways of exiting the SCU program. After finishing with your settings, you must save and exit so that the changes can take effect. Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items.
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the driver disc supplied with your computer. This chapter describes how to install the drivers.
How to Use the Driver CD NOTE: • The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. • You can always find README or document files on the driver CD. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This driver CD supports Windows 98, Windows NT, Windows 2000, Windows XP, and Linux operating systems only.
The main screen appears as shown next: To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Device Driver Ensures the full function of the following drivers. Install this main driver before installing the other drivers. Upon clicking this button, the chipset, VGA, audio, modem, and LAN drivers would be installed one after the other. TPM Allows you to use the TPM (Trusted Platform Module) support for security.
Option Device 6-4 Upon clicking on this, the following screen appears. WLAN Installs the WLAN driver that allows your system to connect wirelessly to the Internet. Bluetooth (option) Allows your computer to connect to Bluetooth -compliant devices. Refer to chapter 2 for detailed instructions on using the Bluetooth feature of your computer. TouchScreen (option) Allows you to use your fingers as a pointing device on the LCD screen (refer to the next section for further instructions).
Vehicle Dock Upon clicking this button on the first page, the following screen appears. Video Capture (option) Allows you to connect a video capture device through the AV input port. USB-to-COM (option) Allows you to use the wireless modem and GPS features to transmit information wirelessly.
Others IrDA (option) Upon clicking on this on the first page, the following screen appears. Installs the Microsoft Hotfix driver for the optional ATi M54-CSP VGA controller. NOTE: You need to install the IrDA driver if your system comes with the ATi M54-CSP VGA controller and if you are using Windows XP Service Pack 2 only. Dual Core Installs the dual core hotfix for Windows XP only. 1394B Allows your computer to connect to IEEE 1394B device.
Browse CD Exit Upon clicking on this on the first page, browses the contents of the driver disc. Exits the driver installation. Touchscreen Driver To install the touch screen driver, perform the following: 1. Insert the driver disc into the optical drive. 2. Click on TouchScreen and follow the onscreen instructions to continue. 3. When finished installing, select Yes to reboot your system. The driver should now be loaded. 4.
5. Click on Standard Calibration. 6. Click on the four sides (points) and the plus-sign “+” on the screen to calibrate your touchscreen for use on the computer.
Using the OSD NOTE: The OSD utility is an option for you. You can decide whether you would like to have this utility installed. With the OSD utility installed, the utility will be activated and an icon will appear on the system tray every time Windows starts up. A graphic display will appear on the screen to indicate the current status of certain operations (as listed next).
Icon Hot Key/Button Operation OSD Description Icon appears on the screen to indicate that LCD display (F10) or backlight (F11) is on or off. The OSD disappears after a few seconds. Fn+F10/F11 Fn+F10/F11 On Off Icon appears on the screen to indicate that wireless LAN is on or off. The OSD disappears after a few seconds. On Off Icon appears on the screen to indicate that AC power cord has been connected or unplugged. The OSD disappears after a few seconds.
CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock.
Taking Care of the Computer Location Guidelines l Use the computer where the temperature is between 0 °C (32 °F) and 60 °C (140 °F). l Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. l Keep the computer at least 13 cm (5 inches) away from electrical appliances that can generate a strong magnetic field such as a TV, refrigerator, motor, or a large audio speaker.
Cleaning Guidelines l Never clean the computer with its power on. l Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. l Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. l Dust on the IR port can interfere with data transfer. Wipe the port with a soft, dry cloth. l Dust or grease on the touchscreen can affect its sensitivity.
When Traveling l Before traveling with your computer, make a backup of your hard disk data into optical discs or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure the battery pack is fully charged. l Make sure the computer is turned off. l Do not leave objects that will press onto the display. l Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger.
7-6 Caring for the Computer
CHAPTER 8 Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: l Try to isolate which part of the computer is causing the problem. l Make sure that you turn on all peripheral devices before turning on the computer. l If an external device has a problem, make sure that the cable connections are correct and secure. l Make sure that the configuration information is properly set in the SCU program.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Bluetooth Problems P. 8-4 Display Problems P. 8-5 Hardware Device Problems P. 8-6 Hard Disk Drive Problems P. 8-6 Infrared Problems P. 8-7 Keyboard, Mouse and Touchpad Problems P. 8-7 LAN Problems P. 8-8 WLAN Problems P. 8-8 Modem Problems P. 8-8 PC Card Problems P. 8-10 Power Management Problems P. 8-10 Printer Problems P.
P. 8-11 Printer Problems The printer does not work. l Make sure that the printer is turned on (if it comes with an independent power source) and is online (ready to use). l Make sure that the printer’s signal cable is properly connected. l Make sure that the printer driver is correctly installed. l Make sure that you have assigned the printer port correctly in your operating system or application program. The printer prints garbled information.
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). l Make sure that the AC adapter is properly connected. l Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. l Make sure that the battery pack is installed correctly. l Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
I cannot end a Bluetooth connection. l If another device is connected to your computer, you can either end the connection using the other device or by deactivating Bluetooth. Display Problems Nothing appears on the screen. l If the power-on indicator is not on, check the electrical outlet, the plugs and power cords. l If the power button does not respond to a light touch, press the button firmly.
The external monitor displays nothing. l Make sure that the monitor is turned on. l Make sure that the monitor’s signal cable is properly connected. l Switch the display to the monitor by pressing Fn+F9, or change the display through the settings in Display Properties. Simultaneous display/multi-display does not work. l Make sure that you turn on the external monitor before turning on the computer.
The hard disk drive operations seem slow. l The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. The hard disk drive in-use indicator glows without blinking. l The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Infrared Problems The IR port does not work.
The numeric keypad is disabled. l Make sure that the Num Lock is switched on. (Check if the Num Lock Indicator N glows or not.) The external keyboard does not work. l Make sure that the keyboard cable is properly connected. The USB mouse does not work. l Make sure that the mouse cable is properly connected. The touchpad does not work, or the pointer is difficult to control with the touchpad. l Make sure that the touchpad is clean. LAN Problems I cannot access the network.
Transmission quality is poor. l Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with. l Check if there is high interference around the environment and solve the problem as described next. Radio interference exists. l Move your computer away from the device causing the radio interference such as microwave oven and large metal objects.
l Use the Web Manager/Telnet of the Access Point to check whether it is connected to the network. l Reconfigure and reset the Access Point. I cannot access the network. l Make sure that the necessary driver(s) is correctly installed. l Make sure that the network configuration is appropriate. l Make sure that the user name or password is correct. l You have moved out of range of the network. l Turn off power management. Modem Problems The modem does not work.
Power Management Problems The computer does not enter Standby or Hibernation mode automatically. l If you have a connection to another computer, the computer does not enter Standby or Hibernation mode if the connection is actively in use. l Make sure that the Standby or Hibernation time-out is enabled. The computer does not enter Standby or Hibernation mode immediately. l If the computer is performing an operation, it normally waits for the operation to finish.
The printer prints garbled information. l Make sure that the printer driver is correctly installed. l Make sure that the printer cable is properly connected. Software Problems An application program does not work correctly. l Make sure that the software is correctly installed. l If an error message appears on the screen, consult the software program’s documentation for further information. l If you are sure the operation has stop, reset the computer.
l Make sure that your computer is equipped with the driver needed. l Click the speaker symbol on the taskbar and check the Windows volume control. l Check the volume control of your computer. Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green. l If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the system operation seems to hang up, first wait. It is possible that the system is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notices. Parts CPU Core logic Cache memory ROM BIOS RAM Display System Video Panel Video controller Audio Video port Controller Ports Keyboard Pointing device Hard disk drive (removable) Specifications Intel Yonah processor (processor no. x48), µFC-BGA package, dual core low voltage, 1.
Parts Specifications I/O ports Communications Modem LAN HSDPA Serial port, parallel port, IEEE 1394B port, two USB ports, IR port, port replicator, RJ-45 port, RJ-11 port, fingerprint sensor (option) 56 K V.92 10/100/1000 Base-T Ethernet (reserved for TPM security function) SIERRA MC8775V .
APPENDIX B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution z Never install telephone wiring during a lightning storm. z Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. z Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. z Use caution when installing or modifying telephone lines. z Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of RF Device NOTE: The information in this section applies to models with the wireless module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Antenna use: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Explosive Device Proximity Warning WARNING: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.