M230 Operation Manual Part Number: 7990011600010000 0000 0001 R00 (August 2006)
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice.
Table of Contents Preface ...................................................................................... vii Chapter 1 Getting Started .....................................................1-1 Getting the Computer Running................................................1-2 Unpacking ..........................................................................1-2 Connecting to AC Power ...................................................1-2 Opening the Cover ................................................
Windows Keys ...................................................................2-6 Function Keys ....................................................................2-6 Fn Key................................................................................2-7 Hot Keys ............................................................................2-7 Using the Touchpad .................................................................2-9 Configuring the Touchpad ...............................................
Power-Saving Tips ................................................................3-11 Chapter 4 Expanding Your Computer..................................4-1 Connecting an External Monitor .............................................4-2 Connecting a USB Device .......................................................4-3 Connecting a Parallel Device...................................................4-4 Connecting a Serial Device .....................................................
Location Guidelines ...........................................................7-4 General Guidelines.............................................................7-4 Cleaning Guidelines ...........................................................7-5 Battery Pack Guidelines .....................................................7-5 When Traveling .......................................................................7-6 Chapter 8 Troubleshooting...................................................
USA and Canada Safety Requirements and Notices......... B-6 European Union CE Marking and Compliance Notices ...
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and 2 appendices. Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. Chapter 3, Managing Power, provides information on power. Chapter 4, Expanding Your Computer, provides information on installing and using peripheral devices.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information that, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
CHAPTER 1 Getting Started Congratulations on purchasing this computer. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover CAUTION: Be gentle when opening and closing the cover.
Powering the Computer Turning On 1. Make sure the computer is connected to AC power. 2. Press the power button. 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this manual. Right-Side Components Ref 1-6 Component Description See Also Primary Battery Pack Supplies power to your computer when external power is not connected. PC Card Slot Accepts a PC card for additional functions.
Left-Side Components Ref Component Description CD/Combo/ DVD Dual Drive Accepts a compact disc (CD) for installing or loading software, accessing data, and playing music/video. Secondary Battery Pack You can purchase a secondary battery pack that supplies power to your computer when external power is not connected. Hard Disk Drive Slot Inside is the hard disk drive of your computer. Getting Started See Also P. 2-17 P. 3-6 P.
Rear Components Ref 1-8 Component Description See Also IR Port Connects an IrDA-compliant device for wireless data transfer. P. 4-7 Power Connector Connects the AC adapter. P. 1-3 Serial Port Connects a serial device, such as an external modem. P. 4-6 RJ-11 Connector Connects the telephone line. P. 2-29 RJ-45 Connector Connects the LAN cable. P. 2-25 VGA Port Connects an external monitor. P. 4-2 Parallel Port Connects a parallel device, such as a printer. P.
Front Components Ref Component Description See Also Top Cover Latch Locks the top cover. P. 1-4 Kensington Lock Locks the computer to a stationary object for security. P. 7-2 Touchscreen Pen (option) Provides a convenient way to use the touchscreen. Can be stretched for better grip and handling. Handle Allows you to carry your computer for an easy grip. Getting Started P.
Ref Component Device Indicators Description See Also Show the current status of the computer’s devices. AC power indicator. P. 3-2 Glows green when the computer is using AC power. Glows red when the computer, using AC power, is in Standby mode. P. 3-3 Battery Charge Indicator Glows green when the battery is fully charged and connected to AC power. Glows amber when the battery is being charged. Battery Power Indicator P. 3-7 Glows green when the computer is using battery power.
Bottom-Side Components Ref Component Description See Also Stereo Speaker Set Sends out sound and voice from the computer. P. 2-20 Memory Slot Contains the memory slot for expanding the memory size of your computer. P. 4-12 Docking Connector (POGO) For connecting to a Port Replicator / car mount (both are available as an option). Release Knob Allows you to remove the CD/Combo/DVD Dual drive as well as eject the secondary battery pack (option). Getting Started P. 2-14 P.
Ref 1-12 Component Description ??? ??? SIM Card Slot Contains the SIM card slot for using the GPS function. See Also P.
Top-open Components Ref Component Power Button Getting Started Description Turns the computer power ON and OFF. See Also P.
Ref Component Description See Also Keyboard Serves as the data input device of the computer. P. 2-4 Touchpad Serves as the pointing device of the computer. P. 2-9 Device Indicators Show the current status of the computer’s devices. Power On Indicator P. 1-5 Glows green when the computer is on. Glows red when the computer is in Standby mode. Hard Disk Drive Indicator P. 2-14 Blinks green when the hard disk drive is active. Blinks red when the hard disk heater is on.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… Do this… To know more about the computer… Go on to the next chapter. To install the operating system if your dealer has not already done so… See the operating system manual. To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
1-16 Getting Started
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a CD disc if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode… Do this… Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover • Pressing Fn+F10 • Pressing the power button To start up or resume again Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard NOTE: Your computer features backlight for your keyboard to help you see the keyboard keys during poor lighting conditions. Press Fn+F1 to turn it on/off (see Hot Keys later in this chapter). Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes. Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals.
NOTE: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead. Euro Symbol You can press the Euro dollar sign on the keyboard.
Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way.
Key Description Switches the display output to one of the following when an external device is connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTE: Fn+F9 will not work when playing a DVD/MPEG movie. Using the VGA utility’s “Graphics Properties” to switch the display output is not allowed. Display switching when in full screen (maximize view) DOS mode is not allowed.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Here are some common terms that you should know when using the touchpad: Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Doubleclick Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag).
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver if you are using Windows.
Using the Touchscreen (Optional) NOTE: Make sure the “Serial Port COM3 (Touchscreen)” item is set properly in the SCU program. (See “Advanced Menu” in chapter 5 for information.) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen (option) located on the handle.
Here are some common terms that you should know when using the touchscreen: Term Action Click/Point Tap gently on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Press lightly on the touchscreen and move your finger until you reach your destination (drag). Finally, release your finger (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Using the Hard Disk Drive Your computer comes with a removable hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
7. Open the hard disk drive slot cover by pressing on both sides of the release latch using your thumb and index fingers. 8. Pull on the ribbon film to remove the hard disk drive compartment. 9. Remove the three front and two rear screws securing the hard disk drive to the compartment and remove the compartment cover.
10. Place the new hard disk drive into the compartment and tighten the three front and two rear screws. 11. Slide the HDD compartment into the slot until it reaches the end. 12. Close the hard disk drive slot cover to secure the HDD compartment.
Using the Optical Drive Depending on the model, your computer comes with a CD, Combo drive, or DVD dual recorder located on the left side of the computer. This drive is usually configured as drive D. The drive uses removable 5.25-inch silver discs, which look like standard music discs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store.
NOTE: For Combo/DVD Dual drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
5. Close the optical drive bay cover to secure the drive in place. If another module is inside the drive bay 4. Check to see if any other module is installed in the optical drive bay. If no other module is inside, proceed directly to step 10. 5. Close the optical drive bay cover. 6. Gently place the computer upside down. 7. Open the optical drive bay cover again by pressing on both sides of the release latch using your thumb and index fingers. 8.
10. Insert the optical drive into the drive bay ( ) and return the release knob ( ). 11. Close the optical drive bay cover to secure the drive in place. Inserting and Removing a Disc Follow this procedure to insert or remove a disc. 1. Turn on the computer. 2. Locate the optical drive bay on the left side of the computer. 3. Open the optical drive bay cover by pressing on both sides of the release latch using your thumb and index fingers. 4.
5. To insert a disc, place down the disc in the tray with its label facing up. Slightly press the center of the disc until it clicks into place. To remove a disc, hold the disc by its outer edge and lift it up from the tray. 6. Gently push the tray back into the drive. NOTE: In the unlikely event that you are unable to release the drive tray by pressing the eject button, you can manually release the disc. (See “Optical Drive Problems” in Chapter 8.
Using the Video Features The video subsystem of your computer features: 14.1-inch TFT (Thin-Film Transistor) color LCD display with 1024×768 XGA (Extended Video Graphics Array) resolution, or 15-inch TFT color LCD display with 1400×1050 SXGA+ (Super Extended Video Graphics Array) resolution. 64 MB shared with system memory. LCD backlight to help you see the display during poor lighting conditions. Press Fn+F7 to turn it on/off (see Hot Keys in this chapter).
Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external CRT monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.) The following table lists the display modes supported by your computer.
Using the Audio Features NOTE: To take advantage of the enhanced audio capabilities, the device driver supplied with your computer must be installed (see chapter 6 for details). If you experience interference while recording, try lowering the microphone recording volume. The audio subsystem of your computer features: External audio connectors ( ) on the rear, and A set of speakers ( ) on the bottom side Ways of playing and recording sound vary with the operating system used.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. NOTE: After connecting an external audio device, make sure that you specify the use of the correct audio device in Windows. ) can be connected to the line-in Audio Output Connector ( connector of powered speakers with built-in amplifiers, headphones, or earphone set. ) can be connected to an external Microphone Connector ( microphone for recording voice or sound.
Using the Communication Features Using the LAN NOTE: To take advantage of the LAN (Local Area Network) feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 10/100/1000Base-T Ethernet module allows you to connect your computer to a network. It supports data transfer rate up to 1000 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN (WLAN) An internal Mini PCI wireless LAN module have been pre-installed by your computer manufacturer at the factory. This allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support WEP (Wired Equivalent Privacy) 64/128-bit data encryption IEEE 802.11a/b/g standard compliance Technology 802.11a 802.11b 802.
3. Click Network Connections, then double-click the Wireless Network Connection icon . 4. Click Properties in the Wireless Network Connection Status dialog box. 5. You can configure your WLAN settings in the Wireless Network Connection Properties dialog box. Turning Off/On the WLAN Radio NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane.
4. If any wireless network is detected, the following window appears on screen. 5. Click to select a wireless network to connect to, and then click Connect. 6. Depending on the settings, you may be asked to enter a wireless security password (encryption key). For more information on the Intel PROSet Wireless utility, click Help? in the Intel(R) PROSet/Wireless window.
Using the Modem NOTE: To take advantage of the modem feature, the device driver supplied with your computer must be installed (see chapter 6 for details). The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
Connecting Using GPRS Your computer can receive General Packet Radio Services (GPRS), a high-speed data-only service that transmits data over a mobile telephone network. In addition, GPRS provides permanent on-line connection. To use GPRS, you must have a subscription to the function with a service provider that supports GPRS. To connect to a GPRS network, you must configure a connection for that service on your computer.
The status of the Bluetooth connection is indicated by the Bluetooth icon located in the system tray in the lower-right part of the screen. Status Icon On (blue with white logo) Connected (blue with green logo) You can use the Bluetooth Utility to configure Bluetooth connection settings and transfer files. Connecting to Another Bluetooth Device 1. Make sure that the target Bluetooth device is turned on, discoverable and within close range. (See the documentation that came with the Bluetooth device.
3. The Add New Connection Wizard window appears. Select Express Mode (Recommended), then click on Next. 4. Select the device to connect to and click on Next. 5. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information.
Sending a File 1. Right-click the icon, and then click Wireless File Transfer. The following screen appears. 2. In the Wireless File Transfer window, click Add to browse for the file to send. The file(s) will show on the File/Folder window. 3. Click the target device from the Transfer-enabled device window, and then click Send to start the transfer procedure.
For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help on your computer by clicking on Help, then Help . . .
HELP FOR ModuleSW PROGRAM Version: ModuleSW 1.0.1.9 The ModuleSW program can to set BlueTooth/WirelessLan/3G modules power ON or OFF and keep the state to system startup. There are 5 subitem can be selection. The menu and subitem as follow: The user can select and click BlueTooth or WirelessLan(WLAN) or 3G subitem to switch module power state. For example: If user select and click "3G ON" subitem .
If user select and click "3G OFF" subitem . ModuleSW will switch 3G module power OFF state to ON and When system startup(or restart) ,ModuleSW will keep 3G module to power ON state. If user move cursor to ModuleSW tray-icon than show BuleTooth/WirelessLan/3G module power state.
CHAPTER 3 Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer. Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging.
Replacing the Primary Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack. To replace the primary battery pack, follow these steps: 1. Make sure the computer is not turned on or connected to AC power. 2. Locate the battery slot on the right side of the system. 3.
5. Slide the new battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery back removal). 6. Close the slot cover to secure the battery pack. Installing the Secondary Battery Pack If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup.
6. The optical drive will slide out partially. Gently pull on it to remove it. 7. Slide the secondary battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery pack removal). 8. Close the slot cover to secure the secondary battery NOTE: The system supports the secondary battery hot-swap function, providing you the ability to replace the battery even during system on.
Always respond to Battery Low by placing your computer on Standby or Hibernation mode, turning off the computer, or connecting the AC adapter. If you do not take any action, the computer will automatically hibernate and turn off. CAUTION: If you are using a flash PC card, do not access the card during battery low periods. This is because the access may take longer than the time it takes the battery to run out of charge, thus making your access to the card unsuccessful.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the system can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down.
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Disable the parallel and serial ports if no devices are connected to these ports. (See “Advanced Menu” in Chapter 5.
3-12 Managing Power
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’s D-type signal connector to the computer’s VGA port. 3. Plug one end of the monitor’s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a USB Device Your computer has two USB ports that supports transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer.
Connecting a Parallel Device Your computer has a parallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port. Follow this procedure to connect a parallel device: 1. Make sure that the “Parallel Port” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2.
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as an external modem. Follow this procedure to connect a serial device: 1. Make sure the “Serial Port COM1” item is set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the rear of the computer. 4. Turn on the computer.
Connecting an IR Device Your computer has an IR (infrared) port for connecting an infrared-equipped device wirelessly such as another computer, printer, or PDA (Personal Digital Assistant). Follow this procedure to connect an IR device: 1. Make sure that the “Serial Port COM2 (FIR)” item is set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 2.
NOTE: During infrared communication, take note of the following: Do not move the computer and IR device. Do not enter Standby mode. Do not use a cell phone or another IR device near the computer. Avoid strong light such as sunlight or fluorescent light. Disable the screen saver.
Connecting an IEEE 1394B Device NOTE: Your IEEE 1394B port will only function under Windows XP SP2. It is also Windows Vista ready. Make sure that the 1394B driver is installed correctly (see chapter 6 for details). To connect an IEEE 1394A (also known as FireWire 400) device to the computer’s IEEE 1394B (also known as FireWire 800) port, you need an optional FireWire 800/FireWire 400 bilingual cable. Your computer has an IEEE 1394B port for connecting IEEE 1394B devices.
Using PC Cards Your computer has a PC card slot. PC cards are credit card-sized peripheral products based on the standards developed by PCMCIA (Personal Computer Memory Card International Association). PCMCIA is a non-profit association for promoting the interchangeability among mobile computers where ruggedness, low power, and small size are critical. PC Card Type Your computer’s PC card slot can accommodate two type II card or one type II card and one smart card (option).
2. Open the PC card slot cover by pressing on both sides of the release latch using your thumb and index fingers. 3. Slide the PC card, with its label facing up, into the slot until the eject button pops out. Eject Button 4. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: 1.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 2 GB on the two 200-pin 400/533 MHz DDR2 SO-DIMM slots. To install the SO-DIMM: 1. Carefully place the notebook computer upside down. 2. Remove the nine screws to detach the SO-DIMM compartment cover.
3. To install the SO-DIMM, match the SO-DIMM's notched part with the socket's projected part and firmly insert the SO-DIMM into the socket at a 20-degree angle. Then push down until the retaining clips lock the SO-DIMM into position. 4. Replace the SO-DIMM compartment cover and secure with nine screws.
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: You see an error message on the screen requesting you to run Setup. You want to restore the factory default settings. You want to modify some specific settings according to the hardware. You want to modify some specific settings to optimize system performance. Starting SCU NOTE: The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
The SCU menu can be divided into four areas: On the top is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. The center column of the menu displays the current configuration information of the system, devices, and memory items. The right column of the menu provides more detailed information when a menu item is highlighted. On the bottom keyboard keys are displayed for navigating the screen.
Moving Around and Making Selections In most cases, you must go through two levels to complete the setting for an item: menu title and submenu. Use the keyboard to move around and make selections. A brief description of keyboard usage is listed next: Key 5-4 Function ←,→ Selects a menu title. ↑,↓ Selects an item or option. +, – Changes the value. Enter 1) Brings up the sub-menu when available. 2) Opens or closes the option window when an item is selected. Esc 1) Displays the Exit menu.
Main Menu The Main menu contains the system date and time as well as the IDE interface setting of the system. System Time sets the system time. System Date sets the system date. IDE Channel 0/1 Master sets the type of storage device installed. The options are User, Auto, CD-ROM, ATAPI Removable, None, IDE Removable, and Other ATAPI.
Advanced Menu The Advanced menu contains the I/O (input/output) configuration settings of the system. Serial Port COM1 enables or disables the serial (COM1) port. The options are Enabled and Disabled. Serial Port COM2 (FIR) enables or disables the infrared (COM2) port. The options are Enabled and Disabled. Serial Port COM3 (Touchscreen) enables or disables the touchscreen (COM3) function. The options are Enabled and Disabled. Serial Port COM4 (XBay) enables or disables the XBay (COM4) port.
Falling Time to Park HDD sets the time (millisecond) for EC to inform SMI to park the HDD during an accidental drop. The options are 0 (disabled) to 127. Free Drop Status specifies if the computer had been free-dropped. The options are Yes and No. CPU Thermal Control Sub-Menu sets the items that control various CPU thermal parameters. Summary Screen sets if the system configuration would be displayed onscreen during system boot-up. The options are Enabled and Disabled.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a boot device from which to load the operating system. A brief description of keyboard usage is listed next: Key 5-8 Function ↑,↓ Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence.
Exit Menu The Exit menu displays ways of exiting the SCU program. After finishing with your settings, you must save and exit so that the changes can take effect. Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items.
5-10 Setup Configuration Utility (SCU)
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the driver disc supplied with your computer. This chapter describes how to install the drivers.
How to Use the Driver CD NOTE: • The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. • You can always find README or document files on the driver disc. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This driver disc supports Windows 2000 and Windows XP as well as Red-hat Linux only.
The main screen appears as shown next: To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Drivers on the First Page Device Driver Ensures the full function of the following drivers. Install this main driver before installing the other drivers. Upon clicking this button, the chipset, VGA, audio, modem, and LAN drivers would be installed one after the other.
TPM Allows you to use the TPM (Trusted Platform Module) support for security. Bluetooth Allows your computer to connect to Bluetooth-compliant devices. TouchScreen Allows you to use your fingers (or optional touchscreen pen) as a pointing device on the LCD screen (refer to the next section for further instructions). User Guide Allows you to view the Operation Manual on screen. NOTE: You need Adobe Acrobat Reader to open the manual file supplied on this driver disc.
Drivers on the Second Page Upon clicking on Next Page, the following screen appears.
Vehicle Dock Upon clicking on this, the following screen appears. Video Capture Allows you to connect a video capture device through the AV input port (option). USB-to-COM Allows you to use the optional wireless modem and GPS features to transmit information wirelessly. Dual Core Installs the dual core hotfix for Windows XP only. 1394B 1394B Please install the 1394 hot fix and note that 1394B will be fully supported by Window Vista . This hotfix for Windows XP only.
NOTE: The OSD utility is an option for you. You can decide whether you would like to have this utility installed. (See the next section for details.) BT Calibration Installs the battery pack automatic calibration utility. NOTE: For Windows 2000 only. Install the DirectX 8.1 driver to take full advantage of multimedia applications. Run the file DX81NTeng.exe located on the /Utility/DirectX/ directory on your driver disc.
Touchscreen Driver To install the touch screen driver, perform the following: 1. Insert the driver disc into the optical drive. 2. Click on TouchScreen and follow the onscreen instructions to continue. 3. When finished installing, select Yes to reboot your system. The driver should now be loaded. 4. After the system has finished rebooting, click on the PenMount located on the taskbar to bring up the PenMount Monitor icon Control Panel. 5. Click on Standard Calibration. 6.
Using the OSD NOTE: The OSD utility is an option for you. You can decide whether you would like to have this utility installed. With the OSD utility installed, the utility will be activated and an icon will appear on the system tray every time Windows starts up. A graphic display will appear on the screen to indicate the current status of certain operations (as listed next).
Icon Hot Key/Button Operation OSD Description Icon appears on the screen to indicate that wireless LAN is on or off. The OSD disappears after a few seconds. Fn+F11 On Fn+F11 Off Icon appears on the screen to indicate that AC power cord has been connected or unplugged. The OSD disappears after a few seconds. AC In AC out Icon appears on the screen to indicate that speaker is on or off. The OSD disappears after a few seconds.
CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use. If the password is set, the prompt requesting for the password appears on the screen whenever the computer is turned on. Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft.
Using an Anti-Virus Strategy New viruses are always being developed nowadays and they are attacking computers even more easily with emails so commonly used worldwide. You can also install a virus-detecting program to monitor potential viruses that could damage your files.
Taking Care of the Computer Location Guidelines Use the computer where the temperature is between 0 °C (32 °F) and 55 °C (131 °F). Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.
Cleaning Guidelines Never clean the computer with its power on. Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. Dust on the IR port can interfere with data transfer. Wipe the port with a soft, dry cloth. Dust or grease on the touchscreen can affect its sensitivity.
When Traveling Before traveling with your computer, make a backup of your hard disk data into USB disks or other storage devices. As an added precaution, bring along an extra copy of your important data. Make sure the battery pack is fully charged. Make sure the computer is turned off. Do not leave objects that will press onto the display. Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger. Hand-carry the computer.
CHAPTER Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer. If an external device has a problem, make sure that the cable connections are correct and secure. Make sure that the configuration information is properly set in the SCU program. Make sure that all the device drivers are correctly installed.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Bluetooth Problems P. 8-4 Optical Drive Problems P. 8-4 Display Problems P. 8-5 Hardware Device Problems P. 8-7 Hard Disk Drive Problems P. 8-7 Infrared Problems P. 8-8 Keyboard, Mouse and Touchpad Problems P. 8-8 LAN Problems P. 8-9 WLAN Problems P. 8-9 Modem Problems P. 8-9 PC Card Problems P. 8-11 Power Management Problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot. Allow time for the battery pack to return to room temperature. Make sure that the battery pack is installed correctly. Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
I cannot end a Bluetooth connection. If another device is connected to your computer, you can either end the connection using the other device or by deactivating Bluetooth. Optical Drive Problems The optical drive cannot read a disc. Make sure that the disc is correctly seated in the tray, with the label facing up. Make sure that the disc is not dirty. Clean the disc with a disc cleaning kit, available in most computer stores. Make sure that the optical drive driver is installed correctly.
Display Problems Nothing appears on the screen. If the power-on indicator is not on, check the electrical outlet, the plugs and power cords. If the power button does not respond to a light touch, press the button firmly. If you are using battery power, make sure that it has a charge remaining and that it is installed correctly. During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. The brightness level might be too low.
Make sure that the monitor’s signal cable is properly connected. Switch the display to the monitor by pressing Fn+F9, or change the display through the settings in Display Properties. Simultaneous display/multi-display does not work. Make sure that you turn on the external monitor before turning on the computer. Press Fn+F9 to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device.
The hard disk drive in-use indicator glows without blinking. The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’s Disk Defragmenter to defragment the files. Infrared Problems The IR port does not work. Make sure that the IR ports of the two device face each other within a ±15-degrees angle and 1 meter (3 feet) distance and there are no obstructions in between. Make sure that the device connected is using an equivalent speed.
The external keyboard does not work. Make sure that the keyboard cable is properly connected. The USB mouse does not work. Make sure that the mouse cable is properly connected. The touchpad does not work, or the pointer is difficult to control with the touchpad. Make sure that the touchpad is clean. LAN Problems I cannot access the network. Make sure that the device driver is correctly installed. Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub.
Radio interference exists. Move your computer away from the device causing the radio interference such as microwave oven and large metal objects. Plug your computer into an outlet on a different branch circuit from that used by the affecting device. Consult your dealer or an experienced radio technician for help. I cannot connect to another WLAN device. Make sure that the WLAN feature is turned on. Make sure that the SSID setting is the same for every WLAN device in the network.
Make sure that the user name or password is correct. You have moved out of range of the network. Turn off power management. Modem Problems The modem does not work. Make sure that the device driver is correctly installed. Make sure that the COM port in the communication software is correctly set. Turn off power management. PC Card Problems The PC card does not work. Make sure that the PC card is correctly seated. If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available.
The computer does not enter Standby or Hibernation mode immediately. If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Standby or Hibernation mode. The computer automatically enters Standby or Hibernation mode when the battery pack is empty. Do any one of the following: − Connect the AC adapter to the computer. − Replace the empty battery pack with a fully charged one.
Software Problems An application program does not work correctly. Make sure that the software is correctly installed. If an error message appears on the screen, consult the software program’s documentation for further information. If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced. Make sure that the volume control is not set too low. Make sure that the device driver is correctly installed.
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green. If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly. If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. Restart your computer.
Other Problems The date/time is incorrect. Correct the date and time via the operating system or SCU program. After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the system operation seems to hang up, first wait. It is possible that the system is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notices. Parts CPU Intel Yonah low voltage dual core processor µ-FCBGA package 1.66 GHz Intel Yonah low voltage dual core processor µ-FCBGA package 1.5 GHz 667 MHz Front Side Bus (FSB), 15 W thermal ceiling Intel 945GM chipset (Calistoga) + ICH7-M (PCI express × 6 channels) L2 2 MB on-die 8 MB Flash EEPROM (includes system and VGA BIOS), Plug-&-Play, ACPI 2.
Parts Storage device Audio Specifications Hard disk drive bay SATA, easily removable for maintenance, optional built-in heater for low temperature support (–20 0C~55 0C), optional low temperature 20 GB without heater Built-in protection to support free drop from 0 to 3 feet in operating mode: 1~3 feet drop protected by G-sensor 0~1 foot drop protected by special resistant-designed construction Optical drive bay Easily swappable bay for slim-type CD/Combo/DVD dual drive, or second battery Audio control
Parts Environment Operating: Humidity Altitude Storage: Operating: Operating: Storage: Change rate: Shock Vibration Drop ESD (electrostatic discharge Specifications Specifications Temperature 0 °C (32 °F) to 55 °C (131 °F) – standard –20 °C (–4 °F) to 60 °C (140 °F) – option –40 °C (–40 °F) to 70 °C (158 °F) 5 % to 95 % RH, non-condensing 15,000 ft 40,000 ft 2,000 ft/min Operating: 15 g, 11 ms half sine wave Storage: 50 g, 11 ms half sine wave Operating: 10~57.5 Hz 0.075 mm, 57.
A-4 Specifications
APPENDIX B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution z z z z z z z Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of RF Device NOTE: The information in this section applies to models with the wireless module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Antenna use: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Explosive Device Proximity Warning WARNING: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use.
Information to User: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT NOTE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operation instruction for satisfying RF exposure compliance.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
