V100 User’s Manual IMPORTANT : This User’s Manual is for Safety Approval purpose only. This is not intended as final release for mass production.
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE The information in this manual is subject to change without notice.
Table of Contents Preface...................................................................................v Notational Conventions ................................................... vi Chapter 1 Getting Started................................................1-1 Getting the Computer Running........................................... 1-2 Unpacking.................................................................... 1-2 Connecting to AC Power...............................................
Hot Keys ..................................................................... 2-6 Using the Touchpad.......................................................... 2-8 Configuring the Touchpad ............................................. 2-9 Using the Touchscreen.................................................... 2-10 Using the Active Digitizer Feature .................................... 2-11 Using the Hard Disk Drive .............................................. 2-12 Replacing the Hard Disk Drive..........
Using PC Cards................................................................ 4-5 PC Card Type.............................................................. 4-5 CardBus Support .......................................................... 4-5 Inserting and Removing a PC Card................................. 4-5 Using the Card Reader ...................................................... 4-7 System Memory Upgrade.................................................. 4-8 Chapter 5 Using BIOS Setup................
Battery Problems.......................................................... 8-4 Bluetooth Problems ...................................................... 8-4 Display Problems.......................................................... 8-5 Hardware Device Problems ........................................... 8-6 Hard Disk Drive Problems............................................. 8-6 Keyboard, Mouse, and Touchpad Problems.................... 8-7 LAN Problems .....................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters, 2 appendices, and an index. l Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. l Chapter 2, Operating Your Computer, tells you how to use the computer’ s components and features. l Chapter 3, Managing Power, provides information on power.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information that, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press the Enter key to complete.
Chapter 1 CHAPTER Getting Started Congratulations on purchasing this ruggedized computer. Your computer incorporates desktop computer capabilities into a compact notebook-sized package. It can greatly enhance your productivity either in the office or at home. And, of course, wherever you need it, the computer is ready and easy “to go.” This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: l Notebook computer l Accessories: − AC adapter − AC power cord − Grid-type hand strap − Driver disc Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing materials in case you need to ship or store the computer in the future.
3. Plug the female end of the AC power cord to the AC adapter and the male end to an electrical outlet (•). 4. When the AC adapter is connected, power is being supplied from the electrical outlet to the AC adapter and onto your computer. Now, you are ready to turn on the computer. CAUTION: When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer.
2. Press the power button. 3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not be exactly the same as those shown in this manual. Right-Side Components Ref Component Description Œ Battery Pack Compartment Inside is the battery pack that supplies power to your computer when external power is not connected.
Left-Side Components Ref Œ Component Power Description Connects the AC adapter. Connector • USB Ports Each of the two ports connects a USB device, such as a flash disk, printer, digital camera, joystick, and more. Ž RJ-11 Connects the telephone line. Connector • RJ-45 Connects the LAN cable. Connector • PCMCIA Slot Each of the two slots accepts a PC card for additional functions. ‘ Card Reader Accepts a SD (Secure Digital) card for removable storage media.
Rear Components Ref Component Description Œ Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device. • Microphone Connects an external microphone. Connector Ž Kensington Lock Locks the computer to a stationary object for security. • VGA Connector Connects an external display monitor. NOTE: Depending on your model, this port could be a serial connector.
Front Components Ref Component Description Œ Hand Strap Holder The hand strap can be attached to the two holders for convenient handling of your computer. • LCD Brightness Adjust the LCD brightness level. Buttons Ž LCD Rotate Button Rotates the LCD display orientation from default landscape to portrait and vice versa. • Security Button • Software Shows or hides the software keyboard on your LCD Keyboard Button display. ‘ Top Cover Latch Locks the top cover.
Bottom Components Ref Component Description Œ Antenna Connector Connects an external antenna. • Expansion Bus Connector Also known as Port Replicator. Ž Memory Slot Inside is the memory slot for expanding the memory size of your computer. • Speaker Sends out sound and voice from your computer. • Wireless LAN (WLAN) Card Slot Inside is the mini PCI-E slot for using a mini PCI-E WLAN card.
Top-open Components Ref Component Description Œ LCD Screen Displays the output of the computer. • WLAN Antenna Serves as the antenna for wireless LAN transmission. Ž Keyboard Serves as the data input device of the computer. • Touchpad Serves as the pointing device of the computer.
Ref • Component Indicators Description Show the current status of the computer’ s devices. AC Power indicator Lights green when the computer is turned on and using AC power. Battery Charge indicator Lights green when the battery is fully charged. Lights orange when the battery is being charged. Blinks orange when the battery’s capacity is below 10 %. Blinks green when battery’s temperature is too high (over 60 oC).
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose... To know more about the computer... Do this... Go on to the next chapter. To install the operating system if your See the operating system manual. dealer has not already done so... To know more about the operating system... Read the operating system manual. To install the drivers if your dealer has See Chapter 6. not already done so...
Chapter 2 CHAPTER Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk. The computer will automatically load the OS after you turn it on. This process is called booting. NOTE: An operating system is the platform for all your software application programs to run on.
To stop in this mode... Hibernation Do this... To start up or resume again Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover • Pressing the Fn+F10 hot key • Pressing the power button Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: l Typewriter keys l Cursor-control keys l Numeric keys l Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: l When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off.
Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way.
Key Fn + F9 Description Switches the display output when external devices are connected. NOTE: This function only applies to Plug & Play display devices. Fn + F10 Serves as the sleep button that you can define with Windows’ Power Options. (See the “Power Management” in Chapter 3.) Euro Symbol You can press the euro dollar sign on various keyboards. l To press the euro sign on a United States-International keyboard, hold down the Alt Gr key and press 5 (which has an euro sign on it).
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Term Drag and drop Action Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location. –or– Gently tap twice on the pad and on the second tap, keep your finger in contact with the pad. Then, move your finger across the pad to drag the selected object to your destination.
Using the Touchscreen NOTE: l This function is not available if your computer comes with the Active Digitizer feature. l Make sure the touchscreen driver has been installed properly (see chapter 6 for details). CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use your finger or the included touchscreen pen (option).
Using the Active Digitizer Feature NOTE: l This function is not available if your computer comes with the touchscreen function. l Make sure the digitizer driver has been installed properly (see chapter 6 for details). CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the LCD display. Doing so may damage the display surface. Use your finger or the included digitizer pen (option).
Using the Hard Disk Drive Your computer comes with a removable hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch SATA (serial ATA) hard disk drive. This type of drive embodies the latest in fast, reliable mass storage by integrating all the control circuitry necessary for operation directly onto the drive itself.
4. Open the hard disk drive slot cover by pressing on both sides of the release latch using your thumb and index fingers. 5. Pull on the ribbon film to remove the hard disk drive bracket. 6. Remove the three front and two rear screws securing the hard disk drive to the bracket and remove the bracket cover. 7. Place the new hard disk drive into the bracket and tighten the three front and two rear screws. 8. Slide the HDD bracket into the slot until it reaches the end. 9.
Using the Video Features The video subsystem of your computer features: l 10.4-inch wide TFT (Thin-Film Transistor) color LCD display with 1024×768 XGA resolution or 12.
For displaying in higher resolutions, you can connect an external monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.
Using the Audio Features NOTE: l To take advantage of the enhanced audio capabilities, the device driver supplied with your computer must be installed. (See chapter 6 for details.) l If you experience interference while recording, try lowering the microphone recording volume.
Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the device driver supplied with your computer must be installed. (See chapter 6 for details.) The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect one end of the modem cable to the RJ-11 connector on the computer and the other end to the phone line.
Using the Wireless LAN Depending on your model, an internal mini PCI-E wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: l Peer-to-Peer (Ad-Hoc) and Access Point (Infrastructure) modes support l WEP (Wired Equivalent Privacy) 64/128-bit data encryption l IEEE 802.11a/b/g standard compliance Technology 802.11a 802.11b 802.
If you need to temporarily turn off the radio, press Fn+F2. To resume network connection, press Fn+F2 again. It takes approximately 30 seconds for your computer to make a successful WLAN connection and approximately 10 seconds to disconnect. Connecting to a Wireless Network To connect to a wireless network: 1. Make sure that the WLAN radio is on (controlled by Fn+F2). 2. Click Start and then Programs. 3. Click Intel PROSet Wireless and then Intel PROSet Wireless. 4.
5. Click to select a wireless network to connect to, and then click Connect. 6. Depending on the settings, you may be asked to enter a wireless security password (encryption key). For more information on the Intel PROSet Wireless utility, click Help? in the Intel(R) PROSet/Wireless window.
Using the Bluetooth Feature (Optional) NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with your computer must be installed. (See chapter 6 for details.) Depending on your model, your computer may incorporate the Bluetooth capability for short-range (about 10 meters) wireless communications between devices without requiring a cable connection. With Bluetooth, data can be transmitted through walls, pockets and briefcases as long as two devices are within range.
3. Click IVT BlueSoleil and then BlueSoleil. The following screen appears. 4. Click View, then Refresh Devices to check if any Bluetooth device is detected.
5. To connect to a new device, click Tools then click Add New Device. 6. Depending on the type of Bluetooth device that you want to connect to, you will need to enter the pertinent information. For detailed information on using the Bluetooth Utility, see the Bluetooth Utility Help on your computer by clicking on Help, then Contents and Index.
Using the GPS (Optional) NOTE: To take advantage of the GPS feature, the GPS driver supplied with your computer must be installed (see chapter 6 for details). Navigation and positioning are crucial to so many activities. To try to figure out where you are and where you are going, you need GPS technology. The Global Positioning System (GPS) is a worldwide radio-navigation system. Turning On/Off the GPS 1. Click Start and then Programs. 2. Click Holux and then GPS Viewer. The following screen appears. 3.
For detailed information on using the GPS Utility, see the GPS Utility Help on your computer by clicking on Help.
Chapter 3 CHAPTER Managing Power Your computer operates either on external AC power or on internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: l The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. l The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
CAUTION: After the computer has been fully recharged, do not immediately disconnect and reconnect the AC adapter to charge it again. Doing so may damage the battery. NOTE: The battery level may automatically lessen due to the self-discharge process (0.21 % per day), even when the battery pack is fully charged (100 %). This happens no matter if the battery pack is installed in the computer.
Battery Automatic Calibration Utility NOTE: To use the Battery Automatic Calibration Utility, the BT Calibration driver supplied with your computer must be installed (see chapter 6 for details). After installing the Battery Pack Automatic Calibration Utility, the Battery Monitor will call up the Battery Learning program every month. Every once-a-month the Battery Monitor will check if the battery temperature is between 10 oC and 39 oC. When it is between 10 oC and 39 oC, the following screen appears.
Error Messages The battery’s performance would degrade as part of its normal wear-andtear after using it for a considerable length of time. The Battery Monitor program would check the battery’s condition and may display the following error messages. You are recommended to replace the battery. Error Message What it means ... The Battery is BAD !! Battery’s performance has gradually Battery Discharge FAIL, deteriorated. The discharge time is Discharge Timer <= Minimum quite short.
Checking the Battery Level NOTE: Any battery level indication is an estimated result. The actual operating time can be different from the estimated time, depending on how you are using the computer. By Operating System You can check the approximate battery level using the battery meter function of the operating system. To read the battery level in Windows, click the icon on the taskbar. (Click the icon if the computer is using AC power.
2. Locate the battery compartment on the right side of the computer. 3. Open the compartment cover by pressing on both sides of the release latch using your thumb and index fingers. 4. Pull on the ribbon strip to remove the battery pack and replace it with a new one. 5. Slide the new battery pack all the way into the slot. Make sure to observe the correct orientation (the ribbon strip must face outward for future battery back removal). 6. Close the compartment cover to secure the battery pack.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time. In general, Windows’ power management works in this way: What... When...
Hibernation NOTE: Make sure that the hibernation feature is enabled in the Hibernate tab of the Power Options Properties from the Control Panel in Windows XP. Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the computer can be turned off. When you use the hibernation feature, you do not have to close the applications.
Power-Saving Tips Aside from enabling your computer’ s power saving mode (see previous section), you can do your part to maximize the battery’ s operating time by following these suggestions. l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level. l If you work with an application that uses a PC card, exit the application when you finish using it. l If you have a PC card installed, remove it when not in use.
Chapter 4 CHAPTER Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting an External Monitor (option) If you want the benefits of a larger display screen with higher resolution, you can connect an external display monitor to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the monitor’ s D-type signal connector to the computer’ s VGA connector. 3. Plug one end of the monitor’ s power cord into the power socket on the monitor and the other end to an electrical outlet. 4.
Connecting a Serial Device Your computer has one or two serial port (depending on model) for connecting a serial device such as a serial mouse or serial communication device (modem). Follow this procedure to connect a serial device: 1. Make sure the “Serial Port COM1/COM2” item is set properly in the BIOS Setup program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the rear of the computer. 4.
Connecting a USB Device Your computer has two USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. USB (Universal Serial Bus) is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer. With its multiple connection capability, up to 127 devices can be connected in a daisy-chain configuration.
Using PC Cards Your computer has two PC card slot. PC cards are credit card-sized peripheral products based on the standards developed by PCMCIA (Personal Computer Memory Card International Association). PCMCIA is a non-profit association for promoting the interchangeability among mobile computers where ruggedness, low power, and small size are critical. PC Card Type Your computer’ s PC card slots can accommodate a type II card. Typical type II cards are flash memory, SRAM, modem, LAN, and SCSI cards.
3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instructions to complete the process. To remove a PC card: 1. Double-click on the Safely Remove Hardware icon found on the Windows XP taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card from the list to disable the card. 3. Push the eject button and the card will slide out slightly. 4. Pull the card out of the slot.
Using the Card Reader NOTE: l If your hard disk is divided into several drives, make sure that all drives have been formatted before using the Card Reader. Otherwise, you may encounter problems when using the Card Reader. l You can use only storage cards. Your Card Reader does not support cards with I/O (input/output) functions such as a wireless network card or Bluetooth card. Your computer has a Card Reader.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 1 GB on the 533 MHz DDR2 SO-DIMM slot. To install the SO-DIMM: 1. Carefully place the notebook computer upside down. 2. Remove the two screws to open the SO-DIMM compartment cover. 3. To install the SO-DIMM, match the SO-DIMM's notched part with the socket's projected part and firmly insert the SO-DIMM into the socket at a 20-degree angle. Then push down until the retaining clips lock the SO-DIMM into position. 4.
Chapter 5 CHAPTER Using BIOS Setup BIOS Setup Utility is a program for configuring the BIOS (Basic Input/ Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the BIOS Setup program.
When and How to Use BIOS Setup When to Use You need to run BIOS Setup Utility when: l You see an error message on the screen requesting you to run BIOS Setup Utility. l You want to restore the factory default settings. l You want to modify some specific settings according to the hardware. l You want to modify some specific settings to optimize the system performance. Starting BIOS Setup NOTE: The BIOS Setup Utility screens shown in this chapter are for your reference only.
The BIOS Setup Utility screen can be divided into four areas: l On the top is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. l The left column of the menu displays the menu items. l The right column of the menu provides more detailed information when a menu item is highlighted. l The bottom of the menu provides keyboard instructions for moving around and making selections.
Moving Around and Making Selections You must go through two or three levels to complete the setting for an item. In most cases, there are two levels: menu title and submenu. Use the keyboard to move around and make selections. Keyboard information can be found at the bottom of the screen. A brief description of keyboard usage is listed next: Key Function ←,→ Selects a menu title. ↑,↓ Selects an item or option. +/– Changes the value. Enter 1) Brings up the sub-menu when available.
Main Menu The Main menu contains the system date and time settings as well as shows the basic configuration of the system. System Time sets the system time. System Date sets the system date.
Advanced Menu The Advanced menu contains the advanced settings as below. ACPI Control Sub-menu Move the cursor to this item and press the Enter key to go into the submenu.
Active Trip Point controls the temperature of ACPI Active Trip Point – the point in which OS will turn the CPU fan on. Passive Cooling Trip Point controls the temperature of ACPI Passive Trip Point – the point in which OS will begin throttling the CPU. NOTE: If the DTS is enabled, only values below 97 OC are valid. Passive TC1/TC2 Value sets the TC1/TC2 values for the ACPI Passive Cooling formula. Passive TSP Value sets the TSP values for the ACPI Passive Cooling formula.
SATA AHCI Configuration sets the enhanced AHCI. Windows XP Service Pack 1 + IAA driver supports AHCI mode. HDD Heater sets if the system automatically turns on the built-in hard disk drive heater for low temperature operation. NOTE: l To use the HDD heater feature, the MTCCTRL driver supplied with your computer must be installed (see chapter 6 for details). l Disable this item to conserve energy when using battery power. HDD Protection enables automatic protection when computer with HDD is dropped.
Security Menu The Security menu contains the TPM (Trusted Platform Module) setting. The TPM is a component on your computer’s mainboard that is specifically designed to enhance platform security above-and-beyond the capabilities of today’ s software by providing a protected space for key operations and other security critical tasks.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. The bootable devices will be automatically detected during POST and shown here, allowing you to set the sequence that the BIOS uses to look for a boot device from which to load the operating system. A brief description of keyboard usage is listed next: Key Function ↑,↓ Selects (highlight) a boot device. +, – Changes the boot sequence. 1 to 4 Loads the default boot sequence.
Exit Menu The Exit menu displays ways of exiting BIOS Setup Utility. After finishing with your settings, you must save and exit so that the changes can take effect. Exit Saving Changes saves the changes you have made and exits BIOS Setup Utility. Exit Discarding Changes exits BIOS Setup Utility without saving the changes you have made. Load Setup Defaults loads the factory default values for all the items. Discard Changes restores the previous values for all the items.
Chapter 6 CHAPTER Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed, your dealer may have already installed the drivers. If not, you need to install the drivers using the disc supplied with your computer. This chapter describes how to install the drivers.
How to Use the Driver Disc NOTE: l The drivers may have been updated after this manual was published. For driver upgrade, please contact your dealer. l This disc supports Windows XP only. You are recommended to install Windows XP Service Pack 2. l The available items may differ according to your computer model. l Do not remove the driver disc when installing the driver. An autorun program is provided on the driver disc to help you easily install the drivers.
To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Drivers on the First Page Device Driver Ensures the full function of the following drivers. Install this main driver before installing the other drivers. Upon clicking this button, the chipset, VGA, audio, modem, and LAN drivers would be installed one after the other.
Driver Allows you to install the driver for using the TPM (Trusted Platform Module) support for security. Application Allows you to install the TPM application. GPS Upon clicking on this, the instructions for installing the GPS driver appears (refer to the next section for further instructions). Bluetooth Allows you to install the Bluetooth driver and application program that allows you to use the Bluetooth feature.
Drivers on the Second Page Upon clicking on Next Page, the following screen appears. Smart Card Allows you to use the Smart Card Reader feature. SD Reader Allows you to use the SD Reader feature.
WCDMA Upon clicking on this, the following screen appears. Driver Allows you to install the driver for using the WCDMA feature. Application Allows you to install the WCDMA application. CDMA Allows you to install the driver for using the CDMA feature. MTCCTRL Allows you to use the built-in heater feature that automatically turns on for low temperature hard disk drive operation. MTCAPP Allows you to use the MTCAPP feature.
BT Calibration Upon clicking on this, the following screen appears. Utility Installs the battery pack automatic calibration utility that includes the Battery Monitor and Battery Learning programs. Help Upon clicking on this, the instructions for using the battery pack automatic calibration utility appears (refer to the next section for further instructions). NOTE: You need Adobe Acrobat Reader to open the User Guide.
GPS Driver To install the GPS driver, perform the following: 1. Insert the driver disc into the optical drive. 2. Click Start à Run.
3. Enter the driver path and file name (e.g., g:\GPS\PL-2303 Driver Installer_GPS.exe), then click OK. 4. When the InstallShield Wizard screen appears, click Next to continue. 5. When the Windows XP Logo Compatibility Test screen appears, click Continue Anyway. 6. When the next screen appears, click Finish to exit the first part of the driver installation. 7. Re-boot your system for the changes to take effect. 8. After the system has finished rebooting, the Found New Hardware Wizard screen would appear.
Chapter 7 CHAPTER Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Cable Lock You can use a Kensington-type cable lock to protect your computer against theft. The cable lock is available in most computer stores. To use the lock, loop the lock cable around a stationary object such as a table. Insert the lock to the Kensington lock hole and turn the key to secure the lock.
Taking Care of the Computer Location Guidelines l Use the computer where the temperature is between 10 °C (50 °F) and 35 °C (95 °F). l Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. l Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface. Otherwise, overheating may occur that results in damage to the computer.
Cleaning Guidelines l Never clean the computer with its power on. l Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. l Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. l Dust or grease on the touchpad can affect its sensitivity. Clean the pad by using adhesive tape to remove the dust and grease on its surface. Battery Pack Guidelines l Recharge the battery pack when it is nearly discharged.
When Traveling l Before traveling with your computer, make a backup of your hard disk data into flash disks or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure that the battery pack is fully charged. l Make sure that the computer is turned off and the top cover is securely closed. l Do not leave objects in between the keyboard and closed display. l Disconnect the AC adapter from the computer and take it with you.
Chapter 8 CHAPTER Troubleshooting Computer problems can be caused by hardware, software, or both. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: l Try to isolate which part of the computer is causing the problem. l Make sure that you turn on all peripheral devices before turning on the computer. l If an external device has a problem, make sure that the cable connections are correct and secure. l Make sure that the configuration information is properly set in the BIOS Setup program.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery Problems P. 8-4 Bluetooth Problems P. 8-4 Display Problems P. 8-5 Hardware Device Problems P. 8-6 Hard Disk Drive Problems P. 8-6 Keyboard, Mouse, and Touchpad Problems P. 8-7 LAN Problems P. 8-7 WLAN Problems P. 8-8 Modem Problems P. 8-8 PC card Problems P. 8-9 P. 8-9 PC Card Problems The PC card does not work. l Make sure that the PC card is correctly seated.
Sound Problems P. 8-11 Startup Problems P. 8-12 Other Problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not light orange). l Make sure that the AC adapter is properly connected. l Make sure that the battery is not too hot or cold. Allow time for the battery pack to return to room temperature. l Make sure that the battery pack is installed correctly. l Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
l Make sure that both devices are compatible. Display Problems Nothing appears on the screen. l During operation, the screen may automatically turn off as a result of power management. Press any key to see if the screen comes back. l The brightness level might be too low. Increase brightness by pressing the Fn+F6 hot key. l The display output might be set to an external device.
l Press the Fn+F9 hot key to toggle through the display options or change the settings in Display Properties in Windows. Hardware Device Problems The computer does not recognize a newly installed device. l The device may not be correctly configured in the BIOS Setup program. Run the BIOS Setup program to identify the new type. l Make sure if any device driver needs to be installed. (Refer to the documentation that came with the device.) l Make sure if the device needs any jumper or switch settings.
Keyboard, Mouse, and Touchpad Problems The keyboard does not respond. l Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. l Make sure that the Num Lock is switched on. (Check if the Num Lock Indicator glows or not.) The external keyboard does not work. l Make sure that the keyboard cable is properly connected. The USB mouse does not work. l Make sure that the mouse cable is properly connected.
WLAN Problems I cannot use the WLAN feature. l Make sure that the mini PCI-E WLAN card is correctly installed. l Make sure that the necessary driver(s) is correctly installed. l Make sure that the WLAN feature is turned on. Transmission quality is poor. l Your computer may be in an out-of-range situation. Move your computer closer to the Access Point or another WLAN device it is associated with. l Check if there is high interference around the environment and solve the problem as described next.
l If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. l Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with. l Make sure that your computer is configured with the same security option (encryption) to the Access Point. l Use the Web Manager/Telnet of the Access Point to check whether it is connected to the network.
l If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. The PC card stops communicating properly. l The application may have been reset when the computer is turned off or in Standby mode. Exit and restart the application. Power Management Problems The computer does not enter Standby or Hibernation mode automatically. l If you have a connection to another computer, the computer does not enter Standby or Hibernation mode if the connection is actively in use.
Software Problems An application program does not work correctly. l Make sure that the software is correctly installed. l If an error message appears on the screen, consult the software program’ s documentation for further information. l If you are sure the operation has stop, reset the computer. (See “Resetting the Computer” later in this chapter.) Sound Problems No sound is produced. l Make sure that the volume control is not set too low. l Make sure that the device driver is correctly installed.
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light blue. l If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly. l If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. l Restart your computer. Other Problems The date/time is incorrect.
l After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life. Call an authorized dealer to replace the RTC battery.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the computer operation seems to hang up, first wait. It is possible that the computer is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
Appendix A APPENDIX Specifications NOTE: Specifications are subject to change without any prior notice. Parts Specifications TM CPU Intel® Core Duo ULV 1.2 GHz processor 533 MHz FSB (Front Side Bus) Cache Memory 2 MB L2 cache Chipset NorthBridge Intel® 945GMS SouthBridge ICH7-M RAM (system) 512 MB DDR2 533 MHz (1 GB option) Display Panel 10.4-inch wide TFT LCD, resolution up to 1024×768 XGA 12.
Parts Specifications PCMCIA Type II × 2 Type II × 1 and Smart Card Reader (option) Card Reader (option) Secure Digital (SD) I/O ports Two USB ports (USB 2.0 support), serial ports × 2 (RS-232), RJ-45 port, RJ-11 port Modem 56 Kbps, ITU V.92 MDC internal fax modem LAN 10/100/1000Base-T Ethernet Wireless LAN (option) Intel® PRO 3945a/b/g Bluetooth (option) Specification 2.0 module Camera (option) Integrated 1.3 M pixel NOTE: Both camera and GPS feature cannot exist at the same time.
Parts Altitude Regulation Specifications Specifications According to IEC 68-2-13 / MIL-STD-810F, Method 500.
Appendix B APPENDIX Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution l Never install telephone wiring during a lightning storm. l Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. l Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. l Use caution when installing or modifying telephone lines. l Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of the RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operating in conjunction with any other antenna or transmitter. INDOOR USE ONLY in 5.15–5.25 GHz band: For 5.15–5.
Antenna use: l High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons. Please contact your professional installer, VAR, or antenna manufacturer for proper installation requirements.
FCC Requirements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Information to User To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate this equipment. IMPORTANT NOTE: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operation instruction for satisfying RF exposure compliance.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.