CA-27 Operation Manual Part Number: 7990 0121 0001 R00 (May 2004)
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
FINNISH VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture.
About the Modem Caution 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch non-insulated tele phone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. 5. Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: The antenna must not be co-located or operating in conjunction with any other any atnenna or transmitter. Radio Frequency Interference Requirements and SAR The FCC with its action in ET Docket 93-62 has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC certified equipment.
The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use: High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons.
Use on Aircraft Caution CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments. EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC).
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by the manufacturer could void the user’ s authority to operate this device.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To ðñï úüí áõôü ðëçñï ß ôéò ðñï âëÝøåéò ôçò ÅõñùðáúêÞò Ï äçãßáò 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “How to Turn Off the Wireless LAN.
Departments in Which the Wireless LAN Module’ s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
Table of Contents Preface ..............................................................................................XiX Chapter 1 Getting Started ............................................................1-1 Getting the Computer Running .............................................1-2 Unpacking.....................................................................1-2 Before You Begin .........................................................1-3 Connecting to AC Power .....................................
Stopping the Computer ...................................................2-2 Using the Wireless Keyboard (option) ..................................2-4 Mouse-control Buttons ...................................................2-4 Typewriter Keys............................................................2-5 Cursor-control Keys.......................................................2-5 Numeric Keypad ...........................................................2-6 Euro Symbol.....................................
Checking the Battery Level............................................3-4 Replacing the Main Battery Pack ...................................3-5 Battery Low Signals and Actions ....................................3-6 Power Management............................................................3-8 Hibernation ...................................................................3-8 Power-Saving Tips............................................................ 3-10 Chapter 4 Expanding Your Computer...............
Chapter 7 Caring for the Tablet PC ...........................................7-1 Protecting the Computer......................................................7-2 Using the Password.......................................................7-2 Using an Anti-Virus Strategy..........................................7-2 Taking Care of the Tablet PC..............................................7-3 Location Guidelines........................................................7-3 General Guidelines ......................
Resetting the Computer..................................................... 8-17 Appendix A Specifications..........................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and 2 appendices. l l l l l l l l l Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. Chapter 2, Operating Your Tablet PC, tells you how to use the computer’ s components and features. Chapter 3, Managing Power, provides information on power.
l Appendix B, Regulatory Information, provides regulatory statements and safety notices on your computer.
Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset. For example: Press Enter to complete.
CHAPTER 1 Getting Started Congratulations on purchasing this Tablet PC. This hand-held computer, having no fan and being almost noiseless, is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: l l 1-2 Tablet PC Accessories: − AC adapter (100~240 VAC, 50~60 Hz) − AC power cord (US, CE, UK, SA) − Private cable − Backup battery switch pin − Driver CD − X-Bay (optional): Module-1: USB 2.
Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing materials in case you need to ship or store the computer in the future. Before You Begin To prevent depletion of the backup battery’ s power during transit, a switch is provided at the bottom-side of the Tablet PC. Be sure to turn the switch to the “ON” position when using the Tablet PC for the first time by using the included backup battery switch pin to slide the switch.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternate: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. l When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Positioning the Tablet PC The computer can be placed upright using its stand found at the back.
Using the Wireless Keyboard (option) The wireless keyboard can either be placed flat on the table or inclined using its stand found at the back. To place the wireless keyboard in an inclined position, pull open the stand located at the back as shown on the next figure. Place the wireless keyboard in front of the Tablet PC with no obstructions between them to allow unhampered communication between the computer and keyboard’ s IR port.
Turning On and Off the Computer Turning On 1. Make sure the computer is connected to AC power. 2. Press the power button Getting Started .
3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “ Stopping the Computer” in Chapter 2 for information.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. Right-Side Components Ref Component Description See Also Œ USB Port Connects a USB device, such as a USB floppy drive, printer, digital camera, joystick, and more. • Microphone Connector Connects an external microphone. P. 2-22 Ž Audio Output Connector Connects a set of headphones, external speakers with amplifier, or an audio recording device.
Ref Component Description See Also • Expansion Port For connecting to: Port Replicator, CD/DVD-RW/Combo drive module, or USB FDD module. ‘ Power Connector Connects the AC adapter. P. 1-4 ’ PC Card Slot Accepts a PC Card for additional functions. P. 4-7 1-10 P.
Left-Side Components Ref Component Œ X-Bay Interface Connects additional wireless LAN, wireless modem (CDPD), external monitor, or five ports (COM1/4, IEEE 1394, LAN, and USB 2.0). • IR Port Connects an IrDA-compliant device for wireless data transfer. P. 1-6, 4-5 Ž RJ-11 Connector Connects the telephone line. P.
Rear Components Ref Component Description See Also Œ Stand System’ s vertical angle of inclination after the stand is released 18 ± 3 o . P. 1-5 • Main Battery Pack Supplies power to your computer when external power is not connected. P. 3-5 Ž Touchscreen Pen Provides a convenient way to use the touchscreen. Can be stretched for better grip and handling. P.
Front Components Ref Component Œ LCD Panel and Touchscreen Displays the output of the computer. Also serves as your touchscreen. P. 2-8 • Power Button Turns the computer power ON and OFF. Also serves as the SUSPEND/RESUME switch. P. 1-7 Ž Volume Control/ Brightness Control/ Battery Capacity Allows you to toggle between adjusting the sound volume of the computer or brightness of the LCD screen, or battery capacity. P.
Ref Component Description See Also Shows the speaker volume, or the LCD brightness level, or the main/backup battery capacity P. 3-4 Suspend mode indicator (in reverse video) P. 3-8 Hard disk drive in-use indicator P. 2-14 Backup battery status indicator P. 3-4 Volume adjust indicator P. 2-21 LCD brightness adjust indicator P.
Bottom-Side Components Ref ΠComponent CCD USB Port Getting Started Description Connects a standard USB CCD PC camera. See Also P.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose… Do this… To know more about the computer… Go on to the next chapter. To install the operating system if your dealer has not already done so… See the operating system manual. To know more about the operating system… Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
CHAPTER 2 Operating Your Tablet PC This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to Tablet PCs, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button . A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a floppy disk or CD if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
If you choose to stop in Standby or Suspend mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Wireless Keyboard (option) Before using the wireless keyboard, see section on “Positioning the Tablet PC and Wireless Keyboard” on chapter 1. Your wireless keyboard has all the standard functions of a full-sized computer keyboard.
Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes. The Control key (Ctrl) is normally used in combination with other keys for program-specific functions. The Alternate key (Alt) is normally used in combination with other keys for program-specific functions. The Escape key (Esc) is usually used for stopping a process. Examples are exiting a program and canceling a command.
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTES: l When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off. l Some software may not be able to use the numeric keypad on the external wireless keyboard.
Windows Keys The keyboard has two keys that perform Windows-specific functions: Windows Logo key and Application key. The Windows Logo key opens the Start menu and performs software-specific functions when used in combination with other keys. The Application key usually has the same effect as a right mouse click. (See your Windows manual for more information.) Function Keys On the top row of the keys are the function keys: F1 to F12.
Using the Touchscreen NOTE: To take advantage of the touchscreen feature, make sure that the touchscreen driver is correctly installed. CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen instead, which can be stretched for better grip and handling.
Term Action Point Move your finger or pen on the touchscreen until the cursor points to the selection on the screen. Click Tap gently anywhere on the touchscreen. Double-click Tap twice on the touchscreen rapidly. Drag and drop Press lightly on the touchscreen and move your finger or pen until you reach your destination (drag). Finally, release your finger or pen (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Using the Floppy Disk Drive (option) Your Tablet PC comes with an USB floppy disk drive as drive A through the USB port on the right side, or port replicator on an optional expansion box, or through the USB port located on the plug of an optional optical drive module, or on the included private cable . A floppy disk drive allows you to install new programs into your computer, or to store information on a removable floppy disk so you can transfer information from one computer to another.
l Through the Expansion Port Plug of the Optical Drive Module – Insert the USB plug of floppy disk drive into the USB port located on the expansion port plug of the optical drive module.
l Through the Private Cable – Insert the USB plug of the floppy disk drive into the USB port located on the private cable . Inserting and Ejecting Floppy Disks To insert a floppy disk, hold it with the arrow facing up and towards the drive. Slide the disk into the drive until it clicks into place. To eject a floppy disk, first ensure that the floppy disk drive in-use indicator is off, and then press the eject button on the drive.
CAUTION: l Never turn off or reset the computer while the floppy disk drive in-use indicator is on. l Always store your floppy disks in a safe, clean container, to protect them from the environment and magnetic fields. l A floppy disk must be formatted before you can use it. (To know how to format a floppy disk, see your operating system manual.
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. A hard disk drive is a storage device with non-removable , rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
Using the Optical Drive (option) Depending on the model, your computer comes with a CD/DVD-RW/ Combo drive module. This drive is usually configured as drive D and is connected to the expansion port located on the right side of the Tablet PC. The drive uses removable 5.25-inch silver discs, which look like standard music CDs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store. l CD drive can read CDs, audio CDs, CD-R, and CD-RW discs.
NOTE: For DVD-RW/Combo drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
2. Press the eject button and the CD tray will slide out partially. Gently pull on it until it is fully extended. 3. To insert a disc, place down the disc in the tray with its label facing up. Slightly press the center of the tray until it clicks into place. To remove a disc, hold the disc by its outer edge and lift it up from the tray. 4. Gently push the tray back into the drive.
Using the Video Features The video subsystem of your computer features: l l l 10.4-inch TFT (Thin-Film Transistor) 18-bit color LCD display with 1024×768 XGA (Extended Graphics Array) resolution. Simultaneous display on LCD and external monitor, which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Display Mode Resolution 640×480 720×480 800×600 848×480 1024×768 1152×864 Operating Your Tablet PC LCD Only CRT Only Simultaneous Display Colors 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 8-bit √ 16-bit √ 2
Display Mode 1280×1024 1600×1200 LCD Only CRT Only Simultaneous Display 8-bit √ 16-bit √ 24-bit √ 8-bit √ 16-bit √ TABLE NOTE: 8-bit = 256 colors; 16-bit = High Color or 65,536 (64 K) colors; 24 and 32-bit = True Color 16,770,000 (16 M) colors.
Using the Audio Features NOTES: l To take advantage of the enhanced audio capabilities, the audio and volume control drivers supplied with your computer must be installed (see Chapter 6 for details). l If you experience interference while recording, try lowering the microphone recording volume.
Ways of pla ying and recording sound vary with the operating system used. See your operating system documentation or online help for specific information. Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. l l 2-22 Microphone Connector ( ) can be connected to an external microphone for recording voice or sound.
Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the device driver supplied with your computer must be installed. The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board. To connect the telephone line to the modem, connect the end nearest the core on the modem cable to the computer’ s RJ-11 connector and the other end to the telephone line.
Using the Wireless LAN Depending on your model, an internal Mini PCI Wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: l 2.
Turning Off/On the WLAN Radio NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to turn off wireless LAN when using your computer in the airplane. The Windows XP WLAN utility must be on for the WLAN function to work. To turn off the WLAN function, turn off the WLAN utility. It takes approximately 30 seconds for your computer to make a successful WLAN connection and approximately 10 seconds to disconnect.
Your computer can send and receive data via a mobile network using the GSM protocol. To send or receive data over a GSM network, you must have an account with a service provider that supports GSM data services, and the service provider must enable the data features on your account.
The Global Positioning System (GPS) is a worldwide radio-navigation system formed from a constellation of 24 satellites and their ground stations. GPS uses these "man-made stars" as reference points to calculate positions accurate to a matter of meters. In fact, with advanced forms of GPS you can make measurements to better than a centimeter! In a sense it is like giving every square meter on the planet a unique address.
2-28 Operating Your Tablet PC
CHAPTER 3 Managing Power Your computer operates either on external AC power, car adapter, or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC and Car Adapter CAUTION: l The AC and car adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. l The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC or car adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Located inside the main battery compartment of the Tablet PC is the switch for turning off power coming from the internal backup battery see chapter 1 for details).
Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. 3.
By Gas Gauge The internal backup battery pack does not support the gas gauge display on the battery itself, but on the exterior side of the main battery pack (option) is a gas gauge for displaying the estimated battery charge. When the main battery pack is not installed in the Tablet PC and you want to know the battery charge, you can press the on/off switch with a pointed device to see the corresponding value of indicator segment that light green.
4. Slide the release lever ( •) to the right and pull the battery pack out of its compartment (Ž) by using your thumb and index finger. 5. Insert the new battery pack into the compartment and slide the release lever first to the right to accommodate it, then releasing it to the lock position. Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% of its charge remaining.
Always respond to Battery Low by placing your computer on hibernation, turning off the computer, or connecting the AC or car adapter. If you do not take any action and after two minutes’ of warning beeps, the computer will automatically hibernate and turn off. CAUTION: l If you are using a flash PC card, do not access the card during battery low periods. This is because the access may take longer than the time it takes the battery to run out of charge, thus making your access to the card unsuccessful.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down. The next time you turn on your computer, you return to exactly where you left off. Manual Power Management You can manually initiate hibernation at any time by pressing the power button and releasing it in less than 4 seconds with the system on. Repeat the action to wake up the system under hibernation.
Power-Saving Tips In addition to your computer’ s automatic power management, you can do your part to maximize the battery’ s operating time by following these suggestions. 3-10 l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level. l Disable the parallel and serial ports if no devices are connected to these ports. (See “Advanced Menu” in Chapter 5.
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Connecting a Serial Device Your computer has a private port for connecting a serial device such as a serial mouse or modem through the private cable . Follow this procedure to connect a serial device: 1. Make sure the COM Ports item is set properly in the SCU program. (See “Advanced Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the included private cable to the private port. Private cable 4. Plug the device cable to the serial port on the private cable . 5.
Connecting a USB Device Your computer has one USB port on the right side for connecting USB devices such as digital camera, scanner, printer, modem, or mouse; and one CCD USB port at the bottom-side for connecting an optional CCD camera. NOTE: You can also use the USB port located on the Expansion Port plug of the optional optical drive module or the included private cable. USB is specified to be an industry standard extension to the PC architecture.
4-4 Expanding Your Computer
Connecting an IR Device Your computer has an IR (InfraRed) port for connecting an infraredequipped device wirelessly such as a wireless keyboard/mouse, another computer, printer, or PDA (Personal Digital Assistant). The infrared feature supports these standards: For the front panel’ s IR port l IR keyboard/mouse that supports Forward FK34PUS002 (US language) specification For the left side’ s IR port l IrDA 1.1 (FIR – Fast Infrared) with 9.6 Kbps to 4.
When using the le ft side’ s IR port: Place the transmitting device where its IR port faces the IR port of your computer within the effective range − within ±15-degrees vertical angle and within ±15-degrees horizontal angle at no greater than 0.8~1.0 meter distance. Place the receiving device where the IR port of the Tablet PC faces its IR port within the effective range − within ±15-degrees vertical angle and within ±15-degrees horizontal angle at no greater than 0.8~1.0 meter distance. 4.
Using PC Cards Your computer has one PC card slot to accommodate one type II card. CardBus Support Your computer’ s PC card slot supports the CardBus specifications. CardBus is the 32-bit version of PC card technology. It allows speeds of up to 133 Mbps at 33 MHz. Typical applications are SCSI host bus, graphic video, and high-speed network cards. Inserting and Removing a PC Card NOTES: l Some PC cards require additional system resources.
3. When a new card is seated, the computer will detect it and try to install the appropriate driver. Follow the on-screen instruction to complete the process. To remove a PC card: 1. Double-click on the Safely Remove Hardware icon found on the Windows XP taskbar and the Safely Remove Hardware window appears on screen. 2. Select (highlight) the PC card you want to disable from the list and click on the Stop button to disable the card. 3. Push the eject button and the card will slide out slightly. 4.
System Memory Upgrade You can upgrade your computer by changing system memory to a maximum of 1 GB on the SO-DIMM slot. However, to avoid damage during the installation procedure, please ask your dealer for help.
4-10 Expanding Your Computer
CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic Input/Output System) settings of the computer. BIOS is a layer of software, called firmware, that translates instructions from other layers of software into instructions that the computer hardware can understand. The BIOS settings are needed by your computer to identify the types of installed devices and establish special features. This chapter tells you how to use the SCU program.
When and How to Use the SCU Program When to Use You need to run the SCU program when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory default settings. l You want to modify some specific settings according to the hardware. l You want to modify some specific settings to optimize system performance. Starting SCU NOTES: l The Setup screens shown in this chapter are for your reference only. The actual items or settings on your computer may differ.
Moving Around and Making Selections A brief description of keyboard (if installed) usage is listed next: Key Function ←, → Selects a menu title. ↑, ↓ Selects an item or option. Enter 1) Brings up the sub-menu when an item with the arrow sign is selected. 2) Opens or closes the options window when an item is selected. Space bar, Cycles through the pre-defined value for the selected item. – Pressing the space bar brings up the next value; pressing the minus (–) key does the contrary.
Main Menu The Main menu contains the basic configuration settings of the system. Date and Time Sets the system time (Hour, Minute, Second) and date (Year, Month, Day).
Internal Numlock Sets if the numeric keypad will function. A check mark (√) indicates enabled, while underline (_) indicates disabled. USB Emulation Sets if the system supports the USB port in DOS mode. A check mark (√) indicates enabled, while underline (_) indicates disabled.
Advanced Menu The Advanced menu contains the Input/Output (I/O) configuration settings of the system. Geyserville Support This item is only available if the CPU you are using supports the Intel® SpeedStep™function. It allows maximum CPU performance when using AC/car power but minimum CPU performance when using battery power. The available options are Enabled and Disabled.
NOTE: For Windows 2000, you need to install the SpeedStep driver to use this function (see Chapter 6 for details). Shared Video Memory Sets the shared memory size of the video controller. The available options are 4M, 8M, 16M, and 32M. NOTE: The shared video memory size of the video controller will depend on your system memory. If your system memory is greater than 256 (512) MB, system will automatically set the above item to 64MB.
Allows you to assign COM1/COM2/COM3/COM4 to specific functions that you wish to use. In general, COM1/COM4 can be assigned to RS-232C (serial port), COM2 can be assigned to IR (InfraRed), while COM3 can be assigned to touchscreen. Select Disabled if you need the resources (3F8/IRQ4 of COM1, 2F8/IRQ3 of COM2, 3E8/IRQ5 of COM3, 2E8/IRQ11 of COM4) for other devices. Sets the communication compatibility mode for the IR port.
HDD Heater Sets if the system automatically turns on the built-in hard disk drive heater for low temperature operation. A check mark (√) indicates enabled, while underline (_) indicates disabled. Function Key 1/2/3 Define (FN1/FN2/FN3) These three items allow user to define the corresponding function key associated with the three function buttons ( , , ) found on the front panel.
NOTE: The backlight switch function is supported only if your LCD is the transflective type (option). Power Button Define Allows you to set whether system power on/off would occur by just pressing the power button (when set at Power) or whether a combination of the speaker volume / LCD brightness down arrow key located on the front panel plus the power button (when set at ê Power) is needed to turn on/off system power. The latter option prevents an accidental system turning on/off during transit.
Security Menu The Security menu contains the security setting that safeguards your system against unauthorized use. Set Password Allows you to set the password for your system. When typing the password, first make sure that Num Lock is off, and then type the password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. If the Enable Password to Power-on sub-item is enabled, the set password is always required to boot the computer.
Hard Disk Boot Sector Helps prevent infection of computer viruses by protecting the hard disk boot sector (partition table) from changes. A check mark (√) indicates enabled, while underline (_) indicates disabled. CAUTION: Disable this item before installing an operating system, running Fdisk or Format program. Otherwise, the intended action will fail.
Boot Menu The Boot menu sets the sequence of the devices to be searched for the operating system. Boot Sequence Sets the first, second, third, and fourth boot device. The system will try to boot from the first device but if it is not available, will try the next boot device. If you set the first boot device to LAN Boot, the system will boot from the LAN server first. The options are Hard Disk Drive, CD-ROM Drive, Floppy Disk Drive, and LAN Boot.
Exit Menu The Exit menu allows you to leave the SCU program. After finishing with your settings, you must save and exit so that the new settings can take effect. Save Changes and Exit saves the changes you have made and exits the SCU program.
Discard Changes and Exit exits the SCU program without saving the changes you have made. Get Default Values loads factory default values for all the items.
Load Previous Values restores previous values for all the items.
CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your Tablet PC, some operating systems require custom software, known as drivers, to be installed. If you purchased the Tablet PC with Windows pre-installed, your deale r may have already installed the drivers. If not, you need to install the drivers using the CD supplied with your Tablet PC. This chapter describes how to install the drivers.
How to Use the CD NOTES: • The drivers may have been updated after this manual was published. For drivers upgrade, please contact your dealer. • You can always find the README or document files on the CD. These files contain the latest information from the software supplier. Please read the files together with this chapter. • This CD supports Windows 2000, Windows XP, and Windows XP Tablet PC edition. Other systems are not supported.
After installing the device drivers, proceed to the following: The touchscreen driver allows you to use your fingers as well as the touchscreen pen as a pointing device. Volume Control The volume control driver allows you to use the volume control buttons located on the front panel.
Name Directory Description Audio driver \WinXP\audio\ or \Win2000\audio\ setup.exe Installs the audio driver that allows you to take full advantage of the audio subsystem. NOTE: The Windows Plug-and-Play capability may automatically detect the new device (Realtek AC'97 codec) and display the wizard requesting for drivers. Click Cancel to bypass the wizard screen(s). Modem driver \WinXP\modem\ \Win2000\modem\ ptuninst.
Dos Mode Setting When connect CRT display, the CRT full screen disappear under the DOS mode, you can follow step as below: 1. Select right side corner ( ) icon then will appear next figure. 2. Select “Graphics Options” then click on the “Graphics Properties”.
3. Select “Device”, “Intel® Dual Display Clone” and check mark indicates enabled “Same display configuration driven on both displays”.
Touchscreen Driver To install the touch screen driver; perform the following: 1. Insert the driver CD into the drive. 2. Click on “TOUCH SCREEN” and follow the onscreen instructions to continue. 3. When finished installing, select “Yes” to reboot your system. The diver should now be loaded.
Touch screen Calibration: 1. After the system has finished rebooting, click on the “Penmount monitor” icon located on the taskbar to bring up the “Penmount Control Panel”. 2. Select the “Standard Calibration” folder and click on “OK”. 3. If you need 4,9,16,25 dot of the calibrate, we suggest select “Advanced Calibration” button to calibrate. 4. Click on the four sides (points) and the plus-sign “+” on the screen to calibrate your touch screen pen for use on the computer. Note: 1.
Intel SpeedStep Utility After installing the SpeedStep driver, you can now optimize the power consumption of the CPU. Click on “Start,” then “Programs,” then “Intel SpeedStep Utility.” The following screen appears as shown next: Make the necessary settings according to your system requirements.
Wireless LAN Utility Installation Upon clicking on the PROSet link on the main screen, the Installation Wizard appears on screen. Upon clicking on “Next,” the following screen appears as shown next. After making your selection, follow the onscreen instructions to complete the wireless LAN utility installation.
CHAPTER 7 Caring for the Tablet PC Taking good care of your computer will ensure a trouble -free operation and reduce the risk of damage to your computer.
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use. If the password is set, the prompt requesting for the password appears on the screen whenever the computer is turned on. The password is set via the SCU program. See “Security Menu” in Chapter 5 for instructions.
Taking Care of the Tablet PC Location Guidelines l l l l l l Use the computer where the temperature is between 10 °C (50 °F) and 35 °C (95 °F). Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust. Do not cover or block any ventilation openings on the computer. For example, do not place the computer on a bed, sofa, rug, or other similar surface.
Cleaning Guidelines l Never clean the computer with its power on. l Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. l Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display. l Dust on the IR port can interfere with data transfer. Wipe the port with a soft, dry cloth. l Dust or grease on the touchscreen can affect its sensitivity.
When Traveling l Before traveling with your computer, make a backup of your hard disk data into floppy disks or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure the battery pack is fully charged. l Make sure the computer is turned off. l Do not leave objects that will press onto the display. l Disconnect the AC adapter from the computer and take it with you. Use the AC adapter as the power source and as a battery-charger.
7-6 Caring for the Tablet PC
CHAPTER 8 Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: l Try to isolate which part of the computer is causing the problem. l Make sure that you turn on all peripheral devices before turning on the computer. l If an external device has a problem, make sure that the cable connections are correct and secure. l Make sure that the configuration information is properly set in the SCU program.
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery problems P. 8-4 Optical drive problems P. 8-5 Display problems P. 8-5 Floppy disk drive problems P. 8-7 Hardware device problems P. 8-7 Hard disk drive problems P. 8-8 Infrared problems P. 8-8 Keyboard and mouse problems P. 8-9 LAN problems P. 8-10 WLAN problems P. 8-10 Modem problems P. 8-12 PC card problems P. 8-12 Power Management problems P.
Battery Problems The battery does not charge (Battery Charge indicator does not appear). l l Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot – gets above 45o C (113 o F) or too cold – below 0 o C (32 o F). Allow time for the battery pack to return to room temperature. l Make sure that the battery pack is installed correctly. l Make sure that the battery terminals are clean. The operating time of a fully charged battery becomes shorter.
Optical Drive Problems The optical drive cannot read a disc. l Make sure that the disc is correctly seated in the tray, with the label facing up. l Make sure that the disc is not dirty. Clean the disc with a disc cleaning kit, available in most computer stores. l Make sure that the optical drive driver is installed correctly. l Make sure that the computer supports the disc or the file format contained. You cannot eject a disc. l The disc is not properly seated in the drive.
l The brightness level might be too low. Increase brightness by pressing on the brightness/volume control button on the front panel of the Tablet PC. l The display output might be set to an external monitor. l Reset the Tablet PC by pressing Ctrl+Alt+Del keys if you are using an external keyboard. l Try turning the computer off, wait a few seconds, then turn it back on. The characters on the screen are dim. l Adjust the brightness. Bad dots appear on the display at all times.
Simultaneous display does not work. l Make sure that you turn on the external monitor before turning on the computer. Floppy Disk Drive Problems The Floppy Disk Drive In-use Indicator stays on. l Make sure that the floppy disk is not physically damaged. l Make sure that the floppy disk is inserted correctly. The disk drive cannot write to a floppy disk. l Make sure that the floppy disk is formatted. l Make sure that the floppy disk is not write-protected.
l For an external device that has its own power switch, make sure that the power is turned on. Hard Disk Drive Problems The hard disk drive error message appears on the screen. l Insert a bootable diskette and check the integrity of your hard drive. l The hard disk drive has defects. Ask your dealer for help. The hard disk drive operations seem slow. l The data files stored on the hard disk drive may be fragmented. Use a tool such as Window’ s Disk Defragmenter to defragment the files.
l Make sure that there is no device radiating infrared rays, such as remote-controlled devices or wireless headphones, near the computer or device. l Make sure that no direct sunlight or fluorescent lamps are near the computer or device. l Make sure that the IR ports are clean. l Make sure that the IR device’ s internal power (batteries) is adequate or connected to AC power. Keyboard and Mouse Problems The external keyboard does not respond. l Try connecting another external keyboard.
l Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub. l Make sure that the network configuration is appropriate. l Make sure that the user name or password is correct. WLAN Problems I cannot use the WLAN feature. l Make sure that the Mini PCI WLAN card is correctly installed. l Make sure that the necessary driver(s) is correctly installed. l Make sure that the WLAN feature is turned on. Transmission quality is poor.
I cannot communicate with the computer in the network when Infrastructure mode is configured. l l Make sure that the Access Point your computer is associated with is powered on and all the LEDs are working properly. If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. l Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with.
PC Card Problems The PC card does not work. l Make sure that the PC card is correctly seated. l If the card requires an IRQ (Interrupt ReQuest), make sure that there is one available. l The PC card may be attempting to use a COM port in a manner that conflicts with the COM port being used by another device. Try running the SCU program to change the COM port setting. If your PC card uses COM1, set COM1 as Disabled. If your PC card uses COM2, set COM2 as Disabled.
The computer does not enter Standby or Suspend mode immediately. l If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Standby or Suspend mode. l The computer automatically enters Standby or Suspend mode when the battery pack is empty. Do any one of the following: − Connect the AC or car adapter to the computer. − Replace the empty battery pack with a fully charged one. The computer does not enter Suspend mode.
Software Problems An application program does not work correctly. l Make sure that the software is correctly installed. l If an error message appears on the screen, consult the software program’ s documentation for further information. l If you are sure the operation has stopped, reset the computer. (See “Resetting the Computer” in this chapter.) Sound Problems No sound is produced. l Make sure that the volume control is not set too low.
l Check the volume control of your computer. Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not appear. l l l If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly. If you are using the battery power, make sure that the battery is not discharged. Check your settings for the item Power Button Define on the SCU Setup’ s “Advanced menu.
l If this message appears when you are booting from the hard disk, insert a bootable disk in the floppy disk drive and check the condition of the hard disk. Other Problems The date/time is incorrect. l l 8-16 Correct the date and time via the operating system or SCU program. After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life.
Resetting the Computer You may have to reset (reboot) your computer on some occasions when an error occurs and the program you are using hangs up. If the system operation seems to hang up, first wait. It is possible that the system is processing data. Periodically check the hard disk drive in-use indicator, if it flashes irregularly, the program may be accessing data and preventing you from using the keyboard.
8-18 Troubleshooting
APPENDIX A Specifications NOTE: Specifications are subject to change without any prior notices. Parts CPU L2 Cache Memory ROM BIOS RAM System Display Shared video Panel Video controller Video port Keyboard (external/wireless) Pointing device Storage device Floppy disk drive Hard disk drive Audio Optical drive Audio controller Audio port Specifications Intel Pentium M processor LV, 1.
Parts Specifications PC card I/O ports Type II × 1, CardBus support On main system Serial port, USB port, docking port, IR port for wireless keyboard/ mouse, RJ-11 fax/modem port On Port Replicator Serial port × 2, ECP/EPP parallel port × 1, USB 1.1 port × 2, module VGA port × 1, PS/2 port (mouse and keyboard), Mic in, Line out On Office Docking Serial port × 2, ECP/EP P parallel port × 1, USB 2.0 port × 4, module VGA port × 1 On Vehicle Serial port × 1, ECP/EPP parallel port × 1, USB 1.
APPENDIX B Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur.
ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
About the Modem Caution l l l l l l l Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using the telephone function (other than a cordless type) during an electrical storm.
On the Use of RF Device NOTE: The information in this section applies to models with the wireless LAN module. USA and Canada Safety Requirements and Notices IMPORTANT NOTE: The antenna must not be co-located or operating in conjunction with any other any atnenna or transmitter. Radio Frequency Interference Requirements and SAR The FCC with its action in ET Docket 93-62 has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC certifie d equipment.
l The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use: l l The antenna must not be co-located or operating in conjunction with any other any atnenna or transmitter. High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons.
EMC Requirements This device uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications Commission (FCC). This device complies with the limits for a Class B digital device pursuant to Part 15 subpart C of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Canada Radio Frequency Interference Requirements To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Greek To ðñï úüí áõôü ðëçñï ß ôéò ðñï âëÝøåéò ôçò ÅõñùðáúêÞò Ï äçãßáò 1999/5/EC. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 1999/5/EC. Italian Questo prodotto è conforme alla Direttiva Europea 1999/5/EC. Norwegian Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 1999/5/EC. Portuguese Este produto cumpre com as normas da Diretiva Européia 1999/5/EC. Spanish Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
General European standards dictate maximum radiated transmit power of 100 mW Effective Isotropic Radiated Power (EIRP) and the frequency range 2400 – 2483.5 MHz. Belgium and the Netherlands In Belgium and the Netherlands, the product may not be used outdoors. See the instructions next under the heading “How to Turn Off the Wireless LAN.
Departments in Which the Wireless LAN Module’ s Maximum EIRP Not Shown in the Previous Table Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approval Turning Off the Wireless LAN Radio NOTE: Turning the wireless LAN radio off is not the same as disabling the wireless LAN card. It is not necessary to disable the card to meet the regulatory requirements.
