82 GV-RK1352 1 R1352 DFR1352 Card Reader 2.2.0 Keypad {GV.RK1352 Only) When accessing an entry using GV-RK1352. you ¢an enter the doors PIN code on the keypad or present theatricals and then enter this card's PIN code ion the Keypad to be granted access. The access mode is defined on G-ASManager: 1. 0~8 Number Keys: Press the number keys to enter the PIN code. 2. # Key: Press the # key to confirm the PIN code. 3. x Key: Press the « key to cancel the PIN code, 2.
8 82 GV-RK1352 1 R1352 DFR1352 Card Reader Next Read Mode select Read UID or Read GID {o set disconnected readers toreador UID {unique identifier) or GID: {Geo Vision 1D) on G-AS ID Cards | Key Fos. you select Read GID: make surfs thees are Wo numbers on your SEASIDE Cards 1 Key Fobs as shove below: if there Is only one number on your VEGAS 1D Cards 1 Key Abs: GI is nob supported. and you mist select Unique Identification (QUID. Click Submit. Note: 1.
(® Elision 2 Select the COM part that disconnected 10 the reader and Click Open COM The'rad square next io the COM port boy: should change to blue to indicate the COM ports correct. Tinder Master Slave; sel the reader lo Slave, Selectman ID number for threader The ID number ranges firm Do 7) Chick Setup: The settings are sent to the reader. The serial number and immanent version of the reader will be automatically detected.
82 GV-RK1352 1 R1352 DFR1352 Card Reader 2.5.2 Adding the Reader to BV-DVRINVE 1. {n GV-DVRINUR. dick the Configure button, select Accessories, and select GV Gandhian Capture Device Setting. This dialog box appears. Tassel one hes Sa |e Sie Bae | Biotin Sig Han Dales Gi una Areas Sana Cam lick the New button. This dialog box appears.
(® Elision 26-Changing the Default Settings of Beeper and LED You mechanical the default settings:of the LED and the beeper by enabling a GV-AS210 HO H2120 F310 HID B10 810 tb thermally control the LED and Vesper "Through this Interface of the controller. vou can seethe controller to trigger there LED, green LED or beeper when the Specified alarm events be Cut: 1. Enable external control of the reader's Beeper and LED by using the GV-RIRKIDFR Con fig AP. 2.
82 GV-RK1352 } R1352 / DFR1352 Card Reader 2: (CHEEK Compendium. GERE San AR VE 20 Opel Om | Case rng : Sen Version eee Daren BELT REED {slier Lien Constant Sophia Condition] Has hat # Slave Pee = al IE Misnomer a = 1 Only Bead GID 3. To enable external control of Beeper or LED, select Beeper, Green LED or Red LED. 4. Select Master from the Master / Slave drop-down list, 5. Select an ID number for the reader.
(® Elision 2.8.2 Wiring the Be operand LED to lhe GV-AE Cantilever To wire the beekeeper LED fo GV-ABZ10/ 21101 21207 4107 41107 8107 8110. connect hie control wires of the reader's Beeper: Red LED or Green LED to any of outpatients on GALS Controller. Wiring LED to G-ADS Controller The diagram below shows the connection for wiring Green LED using GV-RK1352 and CANVASBACK as an example. For Red LED, use the light red wire instead.
After 82 GV-RK1352 1 R1352 DFR1352 Card Reader Wiring vouch need lo got Manageable fo select the lama conditions that will set off threaders beeper: In G-ASManager: Nightstick the G-AS Controller in the device fist, wick Settings; dnd click the Door Gate tab o select the alarm conditions: Human Canon any Farsi Lardner 5 am 2.6.
(® Elision 27 Setting UID or GiD on Contiguity AP By default. the:readers read the UID Ginning identifier on |D cards or key fobs. Using GV: KIDDER Con fig AR volcano sel the GURKHA I RISE TENDERIZER to read GID {Geo Vision iD on SHEAVED Cards! Key Fobs instead. Note: 1. Toss how To install the Con fig AP and bow To identify the COM pot of the reader, refer to 2. Installing GVRRIGDFR Con fig AP and 351 Defined ee (0D Bermudan and Suing the Reader fo Slave.
82 GV-RK1352 1 R1352 DFR1352 Card Reader 4; CHEEK Setup to apply the salting. The serial number and firmware version of the reader will be automatically detected: To use B10.