GV-Mount Accessories Installation Guide Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
© 2016 GeoVision, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision. Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein.
Contents Contents....................................................................................................i Installation Overview .............................................................................vi GV-Mount Series............................................................................................................... vi GV-Housing Series ........................................................................................................... xi Required Accessories...........
Note for Installing the Vandal Proof IP Dome ....................................93 3. Installing the Vandal Proof IP Dome (Part II).................................94 3.1 Straight Tube Box Mount ........................................................................................ 94 3.2 Straight Tube Mount ............................................................................................... 98 3.3 Wall Mount Bracket ..............................................................................
. Installing the Fisheye Camera......................................................180 5.1 Assembling the Fisheye Camera with the Dome Housing......................................180 5.2 Straight Tube Box Mount .......................................................................................183 5.3 Straight Tube Mount ..............................................................................................187 5.4 Wall Mount .....................................................................
Note for Closing the Bullet Camera Cover........................................256 7. Installing the Bullet / Target Bullet / LPR Camera .......................257 7.1 Convex Corner Mount .............................................................................................257 7.2 Concave Corner Mount ...........................................................................................261 7.3 Pole Mount ...........................................................................................
12.5 GV-EFD2101 / EFD3101 In-Ceiling Mount ..........................................................315 12.6 Assembling GV-EFD2101 / EFD3101 with Dome Housing ..................................319 12.7 Wall Pendant Mount ............................................................................................321 12.8 Straight Tube Mount ............................................................................................323 12.9 Straight Tube Box Mount ............................................
Installation Overview GV-Mount Series The GV-Mount Series supports installation of Vandal Proof IP Dome, Fixed IP Dome, Fisheye Camera, IP Speed Dome, Bullet Camera, Arctic Box Camera, Mini Fixed Dome, Mini Fixed Rugged Dome, Target (Mini) Fixed Dome, Target Mini Fixed Rugged Dome and Target Vandal Proof IP Dome in various environments, such as the ceiling, wall surface, wall corner and pole. The supported installation types are listed below.
GV-VD / EVD Series GV-FD / EFD Series GV-FE / FER Series GV-SD Series GV-BL Series GV-BX-E Series / GV-IP LPR Camera Optional Installation Ceiling In-Ceiling Mount *GV-VD Series (II) only *GV-EFD Series only Straight Tube *Outdoor GV-SD Series only Straight Tube Box *Outdoor GV-SD Series only vii
GV-VD / EVD Series GV-FD / EFD Series GV-FE / FER Series GV-SD Series GV-BL Series GV-BX-E Series / GVIP LPR Camera Optional Installation Pole Pole Mount *Outdoor GV-SD Series only Pole Box Mount *Outdoor GV-SD Series only viii
GV-VD / EVD Series GV-FD / EFD Series GV-FE / FER Series GV-SD Series GV-BL Series GV-BX-E Series / GV-IP LPR Camera Optional Installation Corner Convex Corner Mount *Outdoor GV-SD Series only Convex Corner Box Mount *Outdoor GV-SD Series only Corner Concave Corner Mount *Outdoor GV-SD Series only ix
GV-VD / EVD Series GV-FD / EFD Series GV-FE / FER Series GV-MFD Series GV-MDR Series GV-EFD / GVEDR Series Optional Installation Wall Wall Mount Bracket *GV-FD Series only *GV-EFD2101/3101 is not supported.
GV-Housing Series The GV-Housing Series supports outdoor or indoor installation of GV-BX Series with external protection. The supported installation types are illustrated below. For the supported GV-BX models, refer to Note for Installing Box Camera later in this installation guide.
Required Accessories Look up the required accessories for each installation method from the table below. For more information, contact your local dealer. IMPORTANT: 1. GV-VD Series (I) refers to the following models: GV-VD120D / 121D / 122D / 123D / 220D / 221D / 222D / 223D / 320D / 321D / 322D / 323D / 1500 / 2400 / 2500 / 3400; GVVD Series (II) refers to the following models: GV-VD1530 / 1540 / 1540-E / 2430 / 2440 / 2440-E / 2530 / 2540 / 2540-E / 3430 / 3440 / 3440-E / 5340 / 5340-E 2.
Optional Installation Method Required Accessories Ceiling Mount In-Ceiling Mount GV-VD Series (II) GV-Mount914 GV-EFD2101 / 3101 GV-Mount915 GV-EVD Series GV-Mount916 GV-SD220 GV-Mount907 GV-SD220-S / 2300 GV-Mount908 GV-SD2301 / 2411 GV-Mount908-2 GV-BL Series GV-Mount300 GV-BX Series GV-Mount300 + GV-Housing101 GV-BX-E Series GV-IP LPR Camera GV-Mount300 GV-FD Series GV-Mount300 + GV-Mount200 + GV-Mount902 GV-EFD2101 / 3101 GV-Mount300 + GV-Mount200 + GV-Mount917 GV-FE / FER Seri
Optional Installation Method Required Accessories Pole Mount Ø 4’’ ~ 6’’ GV-BL Series GV-Mount400 GV-BX Series GV-Mount400 + GV-Housing101 GV-BX-E Series GV-IP LPR Camera GV-Mount400 GV-FD Series GV-Mount400 + GV-Mount200 + GV-Mount902 GV-EFD2101 / 3101 GV-Mount400 + GV-Mount200 + GV-Mount917 GV-FE / FER Series GV-Mount400 + GV-Mount200 + GV-Mount903 Outdoor GV-SD Series GV-Mount400 GV-VD Series (I) GV-VD Series (II) Pole Mount Ø 6’’ ~ 7.
Optional Installation Method Required Accessories Pole Mount Pole Box Mount Ø 6’’ ~ 7.
Optional Installation Method Required Accessories Wall Mount Tilting Wall Mount GV-FE / FER Series GV-Mount904 *GV-FER12203 is not supported.
Note for Installing Camera Outdoor When installing the camera outdoor, be sure that: 1. The camera is set up above the junction box to prevent water from entering the camera along the cables. 2. Any network, power, audio and I/O cables are waterproofed using waterproof silicon rubber or the like. 3.
Note for Adjusting Focus and Zoom When adjusting the Focus and Zoom Screws (on Bullet Camera, Vandal Proof IP Dome and Fixed IP Dome), do not over tighten the Focus and Zoom screws. The screws only need to be as tight as your finger can do it. It is not necessary to use any tools to get them tighter. Doing so can damage the structure of lens. For example, Zoom Screw Focus Screw Bullet Camera Focus Screw Zoom Screw Fixed IP Dome The maximum torque value for all the zoom and focus screws is 0.049 N.
Note for Supported Power Box Types The supported power box types and required accessory are detailed below: Required Accessory Supported Power Box Type Single Gang Double Gang 4’’ Octagon 4’’ Square GV-FE / FER Series GV-Mount912 9 9 9 9 GV-FD Series GV-Mount913 9 9 9 9 GV-MDR Series GV-MFD Series GV-EFD Series GV-EDR Series GV-Mount910 9 9 9 GV-Mount913 9 9 9 GV-VD Series N/A Camera Type Single Gang 9 Double Gang 4’’ Octagon 9 9 4’’ Square For the Power Box Mount, see the
Note for IP LPR Camera For GV-LPC2211 / LPC2011, see Chapter 7 Installing the Bullet / Target Bullet / LPR Camera for installation instructions. For GV-LPC1100 / LPC1200 / LPR1200 / LPC2210, see Chapter 9 Installing the Arctic Box / IP LPR Camera for installation instructions.
1 Introduction 1. Introduction 1.1 Accessories List Model No. Name Details GV-Mount100 Straight Tube and Junction Box Kit Dimensions 200 x 170 x 257.5 mm / 7.9 x 6.7 x 10.1 in Weight 3.17 kg / 6.99 lb GV-Mount101 Straight Tube Kit Dimensions 219 x 125 x 332 mm / 8.6 x 4.9 x 13.1 in Weight 1.8 kg / 3.97 lb GV-Mount102 Straight Tube Box Mount Dimensions 256 x 256 x 316 mm / 10.1 x 10.1 x 12.4 in Weight 6.6 kg / 14.
Model No. Name Details GV-Mount103 Straight Tube Mount Dimensions 219 x 125 x 340 mm / 8.6 x 4.9 x 13.4 in Weight 2.2 kg / 4.9 lb GV-Mount200 Wall Pendant Tube Dimensions (L x W x D) 200 x 140 x 249 mm / 7.9 x 5.5 x 9.8 in Weight: 0.93 kg / 2.05 lb GV-Mount203 Wall Pendant Tube and Junction Box Kit Dimensions 315 x 195.5 x 225 mm / 12.4 x 7.7 x 8.9 in Weight 2.95 kg / 6.
1 Introduction Model No. Name Details GV-Mount205 Wall Mount Bracket Kit Dimensions 126.5 x 203 x 160 mm / 5 x 8 x 6.3 in (L x W x diameter) Weight 0.5 kg / 1.1 lb GV-Mount206 Wall Mount Bracket Kit Dimensions 126.5 x 211.3 x 176.85 mm / 5 x 8.3 x 6.96 in (L x W x diameter) Weight 0.93 kg / 2.06 lb GV-Mount300 Convex Corner Adapter Kit Dimensions 238.6 x 409.5 mm / 9.4 x 16.1 in Weight 4.27 kg / 9.
Model No. Name Details GV-Mount310 Concave Corner Adapter Kit Dimensions 123.3 x 393.1 mm / 4.9 x 15.5 in Weight 2.96 kg / 6.53 lb GV-Mount400 Pole Mount Bracket Kit (Ø4 ~ 6 in) Dimensions (Bracket) 241 x 161 mm / 9.5 x 6.3 in Steel Strap Diameter Ø4 ~ 6 in Weight 1.70 kg / 3.75 lb GV-Mount410 Pole Mount Bracket Kit (Ø6 ~ 7.5 in) Dimensions (Bracket) 241 x 161 mm / 9.5 x 6.3 in Steel Strap Diameter Ø6 ~ 7.5 in Weight 1.70 kg / 3.
1 Introduction Model No. Name Details GV-Mount702 Extension Tube Four options are available. Dimensions Ø5.4 x 10 or 20 or 30 or 50 cm Ø2.1 x 3.9 / 7.9 / 11.8 / 19.7 in Weight 180 g / 0.4 lb 390 g / 0.86 lb 550 g / 1.21lb 800 g / 1.76 lb GV-Mount900 Wall Mount Bracket Dimensions 154 x 108 x 50 mm / 6.1 x 4.3 x 2 in Weight 240 g / 0.53 lb GV-Mount901 Dome Housing Dimensions Ø186 x 165.35 mm / Ø7.3 x 6.51 in Weight: 690 g / 1.
Model No. Name Details GV-Mount902 GV-FD Series Dome Housing Dimensions Ø186 x 165.35 mm / Ø7.3 x 6.51 in Weight 700 g / 1.54 lb GV-Mount903 Dome Housing Dimensions Ø185.51 x 165.35 mm / 7.3 x 6.51 in Weight 714 g / 1.
1 Introduction Model No. Name Details GV-Mount904 Tilting Wall Mount Bracket Dimensions Ø159.1 x 40.5 mm / Ø 6.3 x 1.6 in Tilt angle: 0-20° GV-Mount907 In-Ceiling Mounting Kit for GV-SD220 IP Speed Dome Dimensions Ø230 x 153.49 mm / Ø9.08 x 6.05 in Weight 0.87 kg / 1.
Model No. Name Details GV-Mount908 In-Ceiling Mounting Kit for GV-SD220-S IP Speed Dome Dimensions Mounting plate: 227 x 286 mm / 8.9 x 11.3 in Weight 2.05 kg / 4.5 lb GV-Mount908-2 In-Ceiling Mounting Kit for GV-SD2301 and GV-SD2411 Dimensions Mounting plate: 205 x 128 x 227 mm / 8.1 x 5 x 8.9 in Weight 3.0 kg / 6.
1 Introduction Model No. Name Details GV-Mount909 Wall Box Mount Bracket Dimensions 170 x 150 x 110 mm / 6.7 x 5.9 x 4.3 in Weight 610 g / 1.34 lb GV-Mount910 Power Box Mount Bracket Dimensions 112 x 98 x 7.5 mm / 4.4 x 3.9 x 0.3 in Weight 105 g / 0.23 lb GV-Mount912 Power Box Mount Bracket Dimensions Ø146 x 10.5 mm / 5.7 x 0.4 in Weight 180 g / 0.4 lb GV-Mount913 Power Box Mount Bracket Dimensions Ø146 x 7.5 mm / 5.7 x 0.3 in Weight 180 g / 0.
Model No. Name Details GV-Mount914 In-Ceiling Mounting Kit for GV-VD Series (II) Dimensions Ø222 x 86 mm / 8.74 x 3.39 in Weight 705 g / 1.55 lb GV-Mount915 In-Ceiling Mounting Kit for GV-EFD2101 / 3101 Dimensions Ø172.5 x 63.8 mm / 7.04 x 2.5 in Weight 424 g / 0.935 lb GV-Mount916 In-Ceiling Mounting Kit for GV-EVD2100 / 3100 Dimensions Ø205 x 63.8 mm / 8 x 2.5 in Weight 645 g / 1.42 lb GV-Mount917 GV-EFD2101 / 3101 Dome Housing Dimensions Ø186 x 97.5 mm / 7.3 x 3.8 in Weight 948 g / 2.
1 Introduction Model No. Name Details GV-Mount918 Wall Mount Bracket Dimensions 145 x 117 x 96 mm / 5.71 x 4.60 x 3.78 in Weight 350 g / 0.77 lb GVHousing101 Housing Box Dimensions 406 x 145 x 109 mm / 16 x 5.7 x 4.3 in Weight 4.69 kg / 10.
1.
1 • Introduction GV-Mount102 13
• GV-Mount103 • GV-Mount200 14
1 • GV-Mount203 • GV-Mount205 Introduction • 15
• GV-Mount206 115.5 100.5 101.7 126.5 176.6 211.3 177 123 82.5 73.1 • GV-Mount300 108 35 210 165 42 42 5 85 40 16 5 9.
1 • Introduction GV-Mount310 108 200 165 42 5 40 35 9 .5 9.5 80 85 40 5 GV-Mount400 / GV-Mount410 37,5 314 163 20 88 5 163 40 37,5 42 81 5 9. 80 85 9.5 165 240 35 68,5 • 9. 9.
• 18 GV-Mount501
1 • GV-Mount901 / Mount902 / Mount903 / Mount917 • GV-Mount908 • GV-Mount908-2 Introduction 19
• GV-Mount909 • GV-Mount910 20
1 • GV-Mount912 • GV-Mount913 Introduction 21
• GV-Mount914 • GV-Mount915 22
1 • Introduction GV-Mount916 23
• 24 GV-Mount918
1 • Introduction GV-Housing101 Supporting Tube 25
1.3 Packing Lists • GV-Mount100 1. Junction Box 2. Box Cover 3. Tube 4. Tube Connector 5. M5 Flat Screw x 4 6. Corrugated Tube Connector 7. No. 2 Torx Wrench • 26 GV-Mount101 1. Mounting Bracket 2. Tube 3. Tube Connector 4. No.
1 • Introduction GV-Mount102 1. Junction Box 2. Box Cover 3. Supporting Plate 4. Box Cover Plate 5. Mounting Cap 6. Tube 7. No. 5 Torx Wrench 8. No. 2 Torx Wrench 9. No. 6 Torx Wrench 10. M8 (16 mm) Screw x 4 11. M8 (20 mm) Screw x 4 12.
• • GV-Mount103 1. Mounting Bracket 2. Mounting Cap 3. Tube 4. No. 2 Torx Wrench GV-Mount200 1. Wall Pendant Tube • GV-Mount203 1. Junction Box 2. Wall Pendant Tube 3. M5 Screw x 2 4. Corrugated Tube Connector 5. No.
1 • Introduction GV-Mount205 Wall Mount Bracket 1. Mounting Plate 2. Housing Plate 3. M4 Screw (8 mm) x 15 4. M4 Screw (40 mm) x 4 5. Screw Anchor x 4 6. M4.5 Plain Washer x 4 7. M4 Split Washer x 4 Note: Installation of GV-Mount205 does not require all 15 M4 screws (8 mm) to be used. GV-FD Series and GV-FE Series need 10 M4 screws, while GV-VD Series need 11 M4 screws for installation.
• GV-Mount206 1. Wall Mount Bracket 2. Mounting Plate 3. Housing Plate 4. M4 Screw (8 mm) x 15 5. M4 Screw (40 mm) x 4 6. Screw Anchor x 4 7. M4.5 Plain Washer x 4 8. M4 Split Washer x 4 Note: Installation of GV-Mount206 does not require all 15 M4 screws (8 mm) to be used. Only 11 M4 screws are needed for installation. The GV-VD Series that GV-Mount205 can be applied to are GV-VD1530 / 1540 / 1540-E / 2430 / 2440 / 2440-E / 2530 / 2540 / 2540-E / 3430 / 3440 / 3440-E / 5340 / 5340-E.
1 • Introduction GV-Mount300 1. Mounting Plate x 2 2. M8 Screw (30 mm) x 4 3. M8 Screw (25 mm) x 4 4. M8 Plain Washer x 6 5. M8 Split Washer x 6 6. M8 Screw Cap x 6 7. M5 Screw (20 mm) x 4 8. M5 Plain Washer x 4 9. M5 Split Washer x 4 10. M5 Screw Cap x 4 11.
• 32 GV-Mount310 1. Mounting Plate x 2 2. M8 Screw (30 mm) x 4 3. M8 Plain Washer x 6 4. M8 Split Washer x 6 5. M8 Screw Cap x 6 6. M5 Screw (20 mm) x 4 7. M5 Plain Washer x 4 8. M5 Split Washer x 4 9. M5 Screw Cap x 4 10.
1 • Introduction GV-Mount400 1. Mounting Bracket 2. Stainless Steel Strap (Ø4 ~ 6 in) x 3 3. M8 Screw (30 mm) x 4 4. M8 Screw (25 mm) x 4 5. Plain Washer x 4 6. Split Washer x 4 7. M8 Screw Cap x 4 8. M5 Screw (20 mm) x 4 9. M5 Plain Washer x 4 10. M5 Split Washer x 4 11. M5 Screw Cap x 4 12.
• 34 GV-Mount410 1. Mounting Bracket 2. Stainless Steel Strap (Ø6 ~ 7.5 in) x 3 3. M8 Screw (30 mm) x 4 4. M8 Screw (25 mm) x 4 5. Plain Washer x 4 6. Split Washer x 4 7. M8 Screw Cap x 4 8. M5 Screw (20 mm) x 4 9. M5 Plain Washer x 4 10. M5 Split Washer x 4 11. M5 Screw Cap x 4 12.
1 • Introduction GV-Mount501 1. Junction Box 2. Box Cover 3. Supporting Plate 4. M8 (30 mm) Screw x 4 5. M8 (20 mm) Screw x 4 6. Waterproof Rubber 7. No. 5 Torx Wrench 8. No. 6 Torx Wrench 9.
• GV-Mount702 1. Extension Tube • 2. Extension Tube Connector GV-Mount900 1. Wall Mount Bracket 2. Screw Anchor x 2 3. Wall Mount Screw x 2 4. M3 Screw (8 mm) x 4 * For GV-FD Series, GV-MFD Series, GVMDR Series, GV-EFD Series and GVEDR Series 5. M5 Screw (10 mm) x 6 * For GV-VD Series • 36 GV-Mount901 1. Dome Housing 2. Housing Cap 3. M4 Screw x 4 4.
1 • Introduction GV-Mount902 1. Dome Housing 2. Housing Cap 3. M4 Screw x 8 4. M6 Screw x 7 5. Left and Right Rack 6. Housing Plate 7. Small Screw x 5 • GV-Mount903 1. Dome Housing 2. Housing Cap 3. M4 Screw x 4 4. M6 Screw x 7 5. Camera Pier x 3 6.
• GV-Mount904 1. Back Cover 2. Back Plate 3. Tilting Rack 4. Long Screw x 3 5. Short Screw x 9 6.
1 • Introduction GV-Mount907 1. Support Rack x 3 2. Mounting Ring 3. Screw x 9 4. Thread Lock, Screw, Washer 5. Mounting Plate x 1 6. Hex Key 7. Lock Plate and Screw 8. Installation Sticker 9.
• 40 GV-Mount908 1. Housing Cap x 1 2. Mounting Plate x 1 3. Screw x 4 4. M6 Screw x 4 5. Hex key x 1 6. Installation Sticker x 1 7. In-ceiling cover x 1 8.
1 • Introduction GV-Mount908-2 1. Housing Cap x 1 2. Mounting Plate x 1 3. Mounting Cap 4. In-ceiling cover x 1 5. Screw x 4 6. M5 Screw x 2 7. Hex key x 1 8. M4 Screw x 2 9.
• GV-Mount909 1. Wall Bracket x 1 2. Screw Anchor x 4 3. Wall Mount Screw x 4 4. M3 Screw (8 mm) x 4 * For GV-FD Series, GV-MFD Series, GVMDR Series, GV-EFD Series, and GVEDR Series 5.
1 • GV-Mount910 1. Mounting Plate x 1 • 2. M3 Screw (8 mm) x 4 GV-Mount912 1. Mounting Plate x 1 • Introduction 2. M3 Screw (8 mm) x 4 GV-Mount913 1. Mounting Plate x 1 2.
• 44 GV-Mount914 1. Bracket x 3 2. In-Ceiling Plate x 1 3. Black Screw x 9 4. In-Ceiling Ring x 1 5. Installation Sticker x 1 6. Round Screw x 4 7. In-Ceiling Cover x 1 8.
1 • Introduction GV-Mount915 1. Bracket x 3 2. In-Ceiling Plate x 1 3. In-Ceiling Cover x 1 4. In-Ceiling Ring x 1 5. M3 Black Screw x 9 6. M3 Screw (6 mm) x 3 7. M3 Short Screw (3 mm) x 2 8. Installation Sticker x 1 9.
• GV-Mount916 1. Bracket x 3 2. In-Ceiling Plate x 1 3. In-Ceiling Cover x 1 4. In-Ceiling Ring x 1 5. M3 Black Screw x 9 6. M4 Screw x 4 7. M3 Short Screw x 2 8. Installation Sticker x 1 9.
1 • Introduction GV-Mount917 1. Dome Housing 2. Housing Cap 3. M4 Small Screw x 7 4. M6 Screw x 7 5. Housing Plate • GV-Mount918 1. Wall Mount Bracket x 1 2. Screw Anchor x 2 3. Wall Mount Screw x 2 4. M3 Screw (8 mm) x 6 5. Plain Washer x 2 Note: Installation of GV-Mount918 for GV-EFD Series, GV-MFD Series and GV-MDR Series does not require all 6 M3 screws (8 mm) to be used.
• 48 GV-Housing101 1. Housing Box x 1 2. Supporting Tube x 1 3. Screw Anchor x 4 4. M5 Screw (35 mm) x 4 5. Short Screw x 1 6. M5 Plain Washer (7 mm) x 4 7. M5 Plain Washer (16 mm) x 1 8. Torx Wrench x 1 9. Silica Gel Bag x 1 10.
2. Installing the Vandal Proof IP Dome (Part I) The information in this chapter applies to GV-VD120D / 121D / 122D / 123D / 220D / 221D / 222D / 223D / 320D / 321D / 322D / 323D / 1500 / 2400 / 2500 / 3400. 2.
1. Unpack the camera body. A. B. C. D. 2. Secure the back cover to the dome housing (GV-Mount901, No. 1) with M4 screws (GVMount901, No. 3). 3. Thread the camera cable through the back cover and the dome housing.
2 Installing the Vandal Proof IP Dome (Part I) 4. Align the camera body so that the protruding part of the back cover fits the camera body and secure them together. 5. Thread the cable through the housing cap (GV-Mount901, No. 2) and secure with M6 screws (GV-Mount901, No. 4).
2.2 Straight Tube Box Mount Required accessories: • GV-Mount100 • GV-Mount901 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
2 Installing the Vandal Proof IP Dome (Part I) 1. Assemble the camera to the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Assemble the tube (GV-Mount100, No. 3) and the tube connector (GV-Mount100, No. 4). 3. Thread the camera cable through the tube and secure the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4). 4. Thread the camera cable through the box cover (GV-Mount100, No.
5. Secure the junction box (GV-Mount100, No. 1) to the ceiling with 4 self-prepared screws. 6. Assemble the corrugated tube connector (GV-Mount100, No. 6) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C. Screw part C to the tube. D.
2 Installing the Vandal Proof IP Dome (Part I) 8. Hook the box cover and secure it with M5 flat screws (GV-Mount100, No. 5). Ethernet Power 9. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See steps 9 and 10 in Hard-Ceiling Mount, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD. C.
2.
2 Installing the Vandal Proof IP Dome (Part I) 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Assemble the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). 3. Thread the camera cable through the tube and assemble the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4). 4. Thread the camera cable through the mounting bracket (GV-Mount101, No.
7. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD. B. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. C. Adjust the angle, focus and zoom of the camera. See steps 9 and 10 in Hard-Ceiling Mount, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD.
2 Installing the Vandal Proof IP Dome (Part I) 2.4 Wall Mount Required accessories: • GV-Mount205 1. Take the wall mount bracket (GV-Mount205, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount205, No. 6). 3. Align and secure the mounting plate (GV-Mount205, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount205, No. 4).
4. Align and secure the housing plate (GV-Mount205, No. 3) to the mounting plate with 3 M4 screws (GV-Mount205, No. 4). 5. Unpack the camera body. A. B. C. D. 6. Align and secure the camera’s back cover to the housing plate with 4 M4 screws (GVMount205, No. 4).
2 Installing the Vandal Proof IP Dome (Part I) 7. Thread the camera cable through the conduit entry at the bottom of the back cover and the wall mount bracket, and refer to step 5D and 5C to secure the camera to the back cover. 8. Secure the wall mount bracket to the wall with 40 mm M4 screws (GV-Mount205, No. 5) and plain washers (GV-Mount205, No. 7). 9. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera.
2.5 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2). 3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later.
2 4. 5. Installing the Vandal Proof IP Dome (Part I) Unpack the camera body. A. B. C. D. Align and secure the back cover to the wall mount bracket with M5 screws (GVMount900, No. 5).
6. Thread the cable through the conduit entry at the bottom of the back cover and follow steps 5C and 5D to re-assemble the camera. 7. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the screws to the wall. 8. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD. B.
2 Installing the Vandal Proof IP Dome (Part I) 2.6 Wall Box Mount Required accessories: • GV-Mount909 IMPORTANT: The GV-Mount909 is not IP66 protected. Make sure you install the camera in a dry place. 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3).
4. Unpack the camera body. A. B. C. D. 5. Align and secure the back cover to the wall mount bracket with four M5 screws (GVMount909, No. 5). 6. Thread the cable through the back cover and wall mount bracket, and follow step 4C and 4D to secure the camera to the back cover. 7. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
2 Installing the Vandal Proof IP Dome (Part I) 2.7 Wall Pendant Mount Required accessories: • GV-Mount200 • GV-Mount901 The user needs to prepare: • Screws for wall x 4 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Thread the camera cable through the wall pendant tube (GV-Mount200, No. 1) and secure the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4).
3. Secure the wall pendant tube to the wall with 4 self-prepared screws. 4. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See steps 9 and 10 in Hard-Ceiling Mount, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD. C. Secure the thread lock, replace the silica gel bag and secure the housing cover.
2 Installing the Vandal Proof IP Dome (Part I) 2.8 Convex Corner Mount with Pendant Tube Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount901 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Thread the camera cable through the wall pendant tube (GV-Mount200, No. 1), and secure the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4).
3. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GV-Mount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6). 4. Thread the camera cable and secure the pendant tube to the mounting plates. Slide the 30 mm M8 screws (GV-Mount300, No. 3) from front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GV-Mount300, No. 6). Backside View 5.
2 Installing the Vandal Proof IP Dome (Part I) 2.9 Convex Corner Mount with Wall Bracket Required accessories: • GV-Mount300 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GV-Mount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
2. Assemble the camera with the wall mount bracket (GV-Mount900, No.1). A. Unpack the camera body. A-1 A-2 A-3 A-4 B. Secure the back cover to the wall mount bracket from the interior with M5 screws (GV-Mount900, No. 5). C. Thread the cable through the conduit entry at the bottom of the back cover and follow step 2A-3 and 2A-4 to secure the camera body.
2 Installing the Vandal Proof IP Dome (Part I) 3. Assemble the camera with the mounting plates. A. Thread the camera cable through the mounting plates. B. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GV-Mount300, No. 6). Backside View 4. Secure the plates to the wall with 8 self-prepared screws. 5. Refer to the indicated sections of the manuals on the software DVD: A.
2.10 Convex Corner Box Mount Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount901 The user needs to prepare: • Screws for wall x 8 • Corrugated tube (3/4’’, ø 26.0 ~ 26.
2 Installing the Vandal Proof IP Dome (Part I) 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GV-Mount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure them with the screw cap (GV-Mount300, No. 6). 3. Secure the junction box (GV-Mount203, No. 1) to the plate from the backside using the 25 mm M8 screw (GV-Mount300, No.
5. Assemble the corrugated tube connector (GV-Mount203, No. 4) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C. Screw part C to the tube. D. Thread the necessary wires and cables from the wall or the ceiling through the corrugated tube, plug the tube to the junction box and secure with part D. Ethernet Power 6.
2 Installing the Vandal Proof IP Dome (Part I) 7. Hinge and hook the pendant tube to the junction box. n et r Ether Powe 8. Connect the network, power and other cables to the camera. See Connecting the Camera, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 User’s Manual on the software DVD. 9. Conceal the junction box with M5 screws (GV-Mount203, No. 3) using the torx wrench (GV-Mount203, No. 5). 10. Refer to the indicated sections of the manuals on the software DVD: A. Access live view.
2.11 Concave Corner Mount with Pendant Tube Required accessories: • GV-Mount200 • GV-Mount310 • GV-Mount901 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GV-Mount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
2 Installing the Vandal Proof IP Dome (Part I) 2. Thread the camera cable and secure the pendant tube to the plates. Slide the 30 mm M8 screws (GV-Mount310, No. 2) from the front and secure from the backside using plain washer (GV-Mount310, No. 3), split washer, (GV-Mount310, No. 4) and M8 screw cap (GV-Mount310, No. 5). Front View Back View 3. Secure the plates to the wall with 8 self-prepared screws. 4. Refer to the indicated sections of the manuals on the software DVD: A.
2.12 Concave Corner Mount with Wall Bracket Required accessories: • GV-Mount310 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GV-Mount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
2 Installing the Vandal Proof IP Dome (Part I) 2. Assemble the camera with the wall mount bracket (GV-Mount900, No.1). A. Unpack the camera body. A-1 A-2 A-3 A-4 B. Secure the back cover to the wall mount bracket with M5 screws (GV-Mount900, No. 5). C. Thread the cable through the conduit entry at the bottom of the back cover and follow step 2A-3 and 2A-4 to secure the camera body.
3. Assemble the camera with the mounting plates. A. Thread the camera cable through the mounting plates. B. Slide the 30 mm M8 screws (GV-Mount310, No. 2) from the front and secure from the backside using plain washer (GV-Mount310, No. 3), split washer, (GV-Mount310, No. 4) and M8 screw cap (GV-Mount310, No. 5). Front View Back View 4. Secure the plates to the wall with 8 self-prepared screws. 5. Refer to the indicated sections of the manuals on the software DVD: A.
2 Installing the Vandal Proof IP Dome (Part I) 2.13 Pole Mount with Pendant Tube Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount901 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Secure the mounting bracket (GV-Mount400 / GV-Mount410, No. 1) to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size.
5. Thread the camera cable through the pendant tube (GV-Mount200, No. 1) and secure the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4). 6. Thread the camera cable through the mounting bracket and secure the pendant tube to the mounting bracket. Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 5), split washer (GV-Mount400 / GV-Mount410, No.
2 Installing the Vandal Proof IP Dome (Part I) 2.14 Pole Mount with Wall Bracket Required accessories: • GV-Mount400 or GV-Mount410 • GV-Mount900 1. Assemble the camera with the wall mount bracket (GV-Mount900, No.1). E. Unpack the camera body. A-1 A-2 A-3 Unscrew A-4 F. Secure the back cover to the wall mount bracket with M5 screws (GV-Mount900, No. 5).
G. Thread the cable through the conduit entry at the bottom of the back cover and follow step 2A-3 and 2A-4 to secure the camera body. 2. Assemble the camera with the mounting bracket (GV-Mount400 / GV-Mount410, No.1). A. Thread the camera cable through the mounting bracket. B. Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 5), split washer, (GV-Mount400 / GV-Mount410, No.
2 Installing the Vandal Proof IP Dome (Part I) 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual - VD. B. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. C. Adjust the angle, focus and zoom of the camera.
2.15 Pole Box Mount Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount901 The user needs to prepare: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 2.1 Assembling the Vandal Proof IP Dome with the Dome Housing. 2. Assemble the mounting bracket (GV-Mount400 / GV-Mount410, No. 1) and the junction box (GV-Mount203, No. 1) from the backside using 25 mm M8 screws (GV-Mount400 / GV-Mount410, No.
Installing the Vandal Proof IP Dome (Part I) 2 3. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. Face the conduit exit downward. 4. Assemble the corrugated tube connector (GV-Mount203, No. 4) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C.
5. Thread the camera cable through the pendant tube (GV-Mount203, No. 2) and secure the tube to the end of the housing cap (GV-Mount901, No. 2) with M6 screws (GV-Mount901, No. 4). 6. Hinge and hook the pendant tube to the junction box. 7. Connect the network, power and other cables to the camera. See Connecting the Camera, Vandal Proof IP Dome (Part I) Chapter, GV-IPCam H.264 Hardware Manual -VD on the software DVD. 8. Conceal the junction box with M5 screws (GV-Mount203, No.
2 Installing the Vandal Proof IP Dome (Part I) 2.
1. Unpack the camera body. A. B. C. D. 2. Thread the camera cable through the back cover and into the power box and secure the back cover to the power box with self-prepared screws. 3. Follow steps 1B to 1D to assemble the camera. 4. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
Note for Installing the Vandal Proof IP Dome When installing GV-VD1530 / 1540 / 1540-E / 2430 / 2440 / 2440-E / 2530 / 2540 / 2540-E / 3430 / 3440 / 3440-E / 5340 / 5340-E, be sure that: 1. When installing the camera near the corner, maintain at least 25 cm away from the walls to avoid reflections. 2. If the center of the camera view is less than 25° to the ceiling, or lower than the grey line (as illustrated below), disassemble the indicated ring so the view is not obstructed.
3. Installing the Vandal Proof IP Dome (Part II) The information in this chapter applies to GV-VD1530 / 1540 / 1540-E / 2430 / 2440 / 2440-E / 2530 / 2540 / 2540-E / 3430 / 3440 / 3440-E / 5340 / 5340-E. 3.1 Straight Tube Box Mount Required accessories: • GV-Mount100 • GV-Mount903 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
Installing the Vandal Proof IP Dome (Part II) 3 1. Assemble the corrugated tube connector (GV-Mount100, No. 6) with the self-prepared corrugated tube and the junction box (GV-Mount100, No. 1). A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C. Screw part C to the tube. D.
4. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the box cover and into the dome housing. 5. Secure the supplied back plate to the dome housing. 6. Thread the wires into the camera. See steps 1 to 3 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD. 7. Secure the camera to the back plate with the supplied torx wrench. 8. Hinge and hook the box cover to the junction box.
3 Installing the Vandal Proof IP Dome (Part II) 9. Connect the wires and close the box cover with M5 flat screws (GV-Mount100, No. 5). 10. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See step 8 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD. C.
3.
3 Installing the Vandal Proof IP Dome (Part II) 1. Assemble the mounting bracket (GV-Mount101, No. 1), tube (GV-Mount101, No. 2), tube connector (GV-Mount101, No. 3), housing cap (GV-Mount903, No. 2) and the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 2. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the box cover and into the dome housing. 3. Secure the supplied back plate to the dome housing. 4. Thread the wires into the camera.
7. Secure the camera to the ceiling with self-prepared screws. 8. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See step 8 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD. C. Replace the silica gel bag and secure the housing cover.
3 Installing the Vandal Proof IP Dome (Part II) 3.3 Wall Mount Bracket GV-Mount206 Required accessories: • GV-Mount206 1. Take the wall mount bracket (GV-Mount206, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount206, No. 6). 3. Align and secure the mounting plate (GV-Mount206, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount206, No. 4).
4. Align and secure the housing plate (GV-Mount206, No. 3) to the mounting plate with 3 M4 screws (GV-Mount206, No. 4). 5. Align and secure the camera’s back plate to the housing plate with 4 M4 screws (GVMount206, No. 4). Back Plate 6. Thread the camera cables through the wall mount bracket. B A A. Thread the wires of power adapter, audio (optional), TV out (optional) and I/O devices (optional) through the hole labeled A. B. Thread the RJ-45 cable through the hole labeled B. 7.
3 Installing the Vandal Proof IP Dome (Part II) 8. Align and secure the camera to the back plate with the supplied torx wrench. 9. Secure the wall mount bracket to the wall with 40 mm M4 screws (GV-Mount206, No. 5) and plain washers (GV-Mount206, No. 7). 10. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
3.4 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
3 Installing the Vandal Proof IP Dome (Part II) 3. Insert the ceiling screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 4. Align and secure the supplied back plate to the wall mount bracket with M5 screws (GVMount900, No. 5). 5. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the wall mount bracket and into the camera.
7. Hang the wall mount bracket on the ceiling screws, push the wall mount bracket downward and tighten the screws to the wall. 8. Connect the camera wires with wires from the wall. 9. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See step 8 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.
3 Installing the Vandal Proof IP Dome (Part II) 3.5 Wall Box Mount Required accessories: • GV-Mount909 IMPORTANT: The GV-Mount909 is not IP66 protected. Make sure you install the camera in a dry place. 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2).
3. Secure the supplied back plate to the wall mount bracket with four M5 screws (GVMount909, No. 5). 4. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the wall mount bracket and into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD 5. Secure the camera to the wall mount bracket with the supplied torx wrench. 6. Connect the camera wires with wires from the wall. 7.
3 Installing the Vandal Proof IP Dome (Part II) 3.
1. Assemble the pendant tube (GV-Mount200, No. 1) with the housing cap (GV-Mount903, No. 2) and then the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 2. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the pendant tube and into the dome housing. 3. Secure the supplied back plate to the dome housing. 4. Thread the wires into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.
3 Installing the Vandal Proof IP Dome (Part II) 6. Connect the camera wires with wires from the wall. 7. Secure the wall pendant tube to the wall with 4 self-prepared screws. 8. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See step 8 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD.
3.7 Convex Corner Mount with Pendant Tube Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1). Slide in the plain washer (GVMount300, No. 4), the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
3 Installing the Vandal Proof IP Dome (Part II) 2. Assemble the pendant tube (GV-Mount200, No. 1) with the housing cap (GV-Mount903, No. 2) and then the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 3. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the pendant tube and into the dome housing. 4. Secure the supplied back plate to the dome housing. 5. Secure the pendant tube to the mounting plates. Slide the 30 mm M8 screws (GVMount300, No.
6. Thread the wires into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD. 7. Secure the camera to the back plate with the supplied torx wrench. 8. Connect the camera wires with wires from the wall. 9. Secure the plates to the wall with 8 self-prepared screws. 10. Refer to the indicated sections of the manuals on the software DVD: A. Access live view.
3 Installing the Vandal Proof IP Dome (Part II) 3.8 Convex Corner Mount with Wall Bracket Required accessories: • GV-Mount300 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GV-Mount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
2. Secure the supplied back plate to wall mount bracket (GV-Mount900, No. 1). 3. Secure the wall mount bracket to the mounting plates. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GV-Mount300, No. 6). Backside View 4. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the mounting plates, wall mount bracket and then into the camera.
3 Installing the Vandal Proof IP Dome (Part II) 5. Secure the camera to the wall mount bracket with the supplied torx wrench. 6. Connect camera wires with wires from the wall. 7. Secure the plates to the wall with 8 self-prepared screws. 8. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
3.9 Convex Corner Box Mount Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 • Corrugated tube (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the mounting plates, slide in the plain washer (GV-Mount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
3 Installing the Vandal Proof IP Dome (Part II) 2. Secure the junction box (GV-Mount203, No. 1) to the plate from the backside using the 25 mm M8 screw (GV-Mount300, No. 3), plain washer (GV-Mount300, No. 4) and split washer (GV-Mount300, No. 5). Back View 3. Install the corrugated tube and the tube connector (GV-Mount203, No. 4) to the junction box. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube.
5. Assemble the pendant tube (GV-Mount203, No. 2), housing cap (GV-Mount903, No. 2) and the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 6. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the pendant tube and into the dome housing. 7. Secure the supplied back plate to the dome housing. 8. Thread the wires into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.
3 Installing the Vandal Proof IP Dome (Part II) 10. Hinge and hook the pendant tube to the junction box. n et r Ether Powe 11. Connect the wires and close the junction box with M5 screws (GV-Mount203, No. 3). 12. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
3.
3 Installing the Vandal Proof IP Dome (Part II) 1. Assemble the mounting plates (GV-Mount310, No. 1). Slide in the plain washer (GV-Mount310, No. 4), then the split washer (GV-Mount310, No. 5), and secure with the screw cap (GV-Mount310, No. 6). 2. Assemble the pendant tube (GV-Mount200, No. 1) with the housing cap (GV-Mount903, No. 2) and then the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 3.
5. Secure the pendant tube to the mounting plates. Slide the 30 mm M8 screws (GV-Mount310, No. 3) from front and secure from the backside using plain washer (GV-Mount310, No. 4), split washer (GV-Mount310, No. 5) and screw cap (GV-Mount310, No. 6). Front View Back View 6. Connect these wires to the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD. 7. Secure the camera to the back plate with the supplied torx wrench.
3 Installing the Vandal Proof IP Dome (Part II) 3.11 Concave Corner Mount with Wall Bracket Required accessories: • GV-Mount310 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GV-Mount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
2. Secure the supplied back plate to wall mount bracket (GV-Mount900, No. 1). 3. Secure the wall mount bracket to the mounting plates. Slide the 30 mm M8 screws (GV-Mount310, No. 2) from the front and secure from the backside using plain washer (GV-Mount310, No. 3), split washer, (GV-Mount310, No. 4) and M8 screw cap (GV-Mount310, No. 5). Front View Back View 4.
3 Installing the Vandal Proof IP Dome (Part II) 7. Secure the plates to the wall with 8 self-prepared screws. 8. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See step 9 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD. C. Replace the silica gel bag and secure the housing cover.
3.12 Pole Mount with Pendant Tube Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount903 1. Assemble the pendant tube with housing cap (GV-Mount903, No. 2) and then the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4).
3 Installing the Vandal Proof IP Dome (Part II) 2. Secure the pendant tube (GV-Mount200, No. 1) with the mounting bracket (GV-Mount400 / 401, No. 1). Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 5), split washer (GV-Mount400 / GV-Mount410, No. 6) and screw cap (GV-Mount400 / GV-Mount410, No. 7). Backside View 3.
6. Secure the camera to the back plate with the supplied torx wrench. 7. Connect camera wires with wires from the pole. 8. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. 9. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual.. B. Adjust the angle, focus and zoom of the camera.
3 Installing the Vandal Proof IP Dome (Part II) 3.13 Pole Mount with Wall Bracket Required accessories: • GV-Mount400 or GV-Mount410 • GV-Mount900 1. Secure the supplied back plate to wall mount bracket (GV-Mount900, No. 1).
2. Secure the wall mount bracket (GV-Mount900, No. 1) to the mounting bracket (GV-Mount400 / GV-Mount410, No.1). Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 5), split washer, (GV-Mount400 / GV-Mount410, No. 6) and M8 screw cap (GV-Mount400 / GV-Mount410, No. 7). Backside View 3.
3 Installing the Vandal Proof IP Dome (Part II) 5. Connect the camera wires with wires from the pole. 6. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. 7. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
3.14 Pole Box Mount Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount903 The user needs to prepare: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the junction box (GV-Mount203, No. 1) with the mounting bracket (GV-Mount400 / 410, No. 1) with the plain washer (GV-Mount400 / GV-Mount410, No. 5), split washers (GV-Mount400 / GV-Mount410, No. 6) and then the 25 mm M8 screws (GV-Mount400 / GV-Mount410, No. 4).
3 Installing the Vandal Proof IP Dome (Part II) 2. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. Face the conduit exit downward. 3. Install the corrugated tube and the tube connector (GV-Mount203, No. 4) to the junction box. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C.
4. Assemble the pendant tube (GV-Mount203, No. 2), housing cap (GV-Mount903, No. 2) and the dome housing (GV-Mount903, No. 1) with M6 screws (GV-Mount903, No. 4). 5. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the pendant tube and into the dome housing 6. Secure the supplied back plate to the dome housing. 7. Thread the wires into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.
3 Installing the Vandal Proof IP Dome (Part II) 9. Hinge and hook the pendant tube to the junction box. n et r Ether Powe 10. Connect the wires and close the junction box with M5 screws (GV-Mount203, No. 3) with the torx wrench (GV-Mount203, No. 5) 11. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera.
3.15 Power Box Mount The user needs to prepare • Screws for securing the camera to power box Supported Power Box Types Single Gang Double Gang 9 4’’ Octagon 4’’ Square 9 1. Thread the power (supplied), network (self-prepared) and other wires (supplied) through the power box and the supplied back plate and then secure the back plate to the power box with self-prepared screws.
3 Installing the Vandal Proof IP Dome (Part II) 2. Thread the wires into the camera. See steps 1 to 4 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD. 3. Secure the camera to the back plate with the supplied torx wrench. 4. Refer to the indicated sections of the manuals on the software DVD: A. Access live view. See Accessing the Live View, Getting Started Chapter, GV-IPCam H.264 Firmware Manual. B.
3.16 In-Ceiling Mount The thickness of the ceiling board must not exceed 4 cm (1.57 in). Required accessories: • GV-Mount914 1. Assemble the in-ceiling casing. A. Secure two brackets (GV-Mount914, No. 1) to the in-ceiling plate (GV-Mount914, No. 2) with black screws (GV-Mount914, No. 3).
3 Installing the Vandal Proof IP Dome (Part II) B. Assemble the in-ceiling ring (GV-Mount914, No. 4). Make sure the arrows point to the same direction. C. Assemble the third bracket and secure it with a black screw (GV-Mount914, No. 3). D. Secure the brackets on the underside with black screws (GV-Mount914, No. 3).
2. Paste the sticker (GV-Mount914, No. 5) to the ceiling, and then remove the part of the ceiling with sticker on. 3. Secure the casing into the ceiling. A. Thread the necessary wires through the casing. B. Insert the casing into the ceiling and make sure the plastic clip is turned outward. IMPORTANT: Make sure the arrow points (see step 1B) to the camera’s viewing direction. C. Tighten the bracket to clip the casing to the ceiling.
3 Installing the Vandal Proof IP Dome (Part II) 4. Secure the back plate (standard package) to the in-ceiling plate using the round screws (GV-Mount914, No. 6) and secure the safety lock (standard package). Align the arrow of the back plate with the in-ceiling ring. 5. Connect the wires to the camera. For details, see steps 1 to 4, Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD on the software DVD. 6.
C. Replace the silica gel bag and secure the housing cover. See step 10 in Installation, Vandal Proof IP Dome (Part II) Chapter, GV-IPCam H.264 Hardware Manual - VD. 8. Secure the in-ceiling cover (GV-Mount914, No. 7) to the in-ceiling ring with the thread screw (GV-Mount914, No.8) and install the ring to the camera. Note: Make sure the markings on the ring align with the arrow (casing).
4. Installing the Fixed IP Dome 4.1 Basic Installation 4.1.1 Assembling the Fixed IP Dome with the Dome Housing Required accessories: • GV-Mount902 1. Unpack the camera package and remove the camera body.
2. Secure the camera body to the housing plate (GV-Mount902, No. 6) with 3 small screws (GV-Mount902, No. 7). 3. Secure the plate to the dome housing with M4 screws (GV-Mount902, No. 3). 4. Secure the housing cap and the dome housing with M6 screws (GV-Mount902, No. 4).
4 Installing the Fixed IP Dome 4.1.2 Putting on the Housing Cover 1. Secure the right and left rack (GV-Mount902, No. 5) to the housing cover. 2. Secure the housing cover to the camera with M4 screws (GV-Mount902, No. 3).
4.2 Straight Tube Box Mount Required accessories: • GV-Mount100 • GV-Mount902 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
4 Installing the Fixed IP Dome 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Secure the junction box (GV-Mount100, No. 1) to the ceiling with 4 self-prepared screws. 3. Assemble the corrugated tube connector (GV-Mount100, No. 6) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C.
4. Thread the wires and cables through the box cover (GV-Mount100, No. 2), hook the box cover and secure it with M5 flat screws (GV-Mount100, No. 5). Power Ethernet Ethernet Or Power 5. Assemble the tube (GV-Mount100, No. 3) and the tube connector (GV-Mount100, No. 4). 6. Thread the wires and cables through the tube, assemble the tube to the box cover and tighten the torxes with the supplied torx wrench (GV-Mount100, No. 7).
4 Installing the Fixed IP Dome 7. Thread the wires and cables through the housing cap (GV-Mount902, No. 2) and secure the tube to the end of the housing cap with M6 screws (GV-Mount902, No. 4). 8. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Adjust the angle, focus and zoom of the camera.
4.
4 Installing the Fixed IP Dome 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Thread the necessary cables and wires from the ceiling through the mounting bracket (GV-Mount101, No. 1) and secure the bracket to the ceiling with 4 self-prepared screws. Ethernet Or Power 3. Assemble the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). 4.
6. Secure the tube to the end of the housing cap (GV-Mount902, No. 2) with M6 screws (GV-Mount101, No. 4). 7. Refer to the indicated sections of the manuals on the software DVD: A. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom of the camera. See steps 6 and 7 in Hard-Ceiling Mount, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. 8. Put on the housing cover. See 4.1.2 Putting on the Housing Cover.
4 Installing the Fixed IP Dome 4.4 Wall Mount Required accessories: • GV-Mount205 1. Take the wall mount bracket (GV-Mount205, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount205, No. 6). 3. Align and secure the mounting plate (GV-Mount205, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount205, No. 4).
4. Align and secure the housing plate (GV-Mount205, No. 3) to the mounting plate with 3 M4 screws (GV-Mount205, No. 4). 5. Unpack and remove the camera cover with supplied torx wrench. 6. Align and secure the camera body to the housing plate with 3 M4 screws (GV-Mount205, No. 4).
4 Installing the Fixed IP Dome 7. Thread the camera cables through the wall mount bracket. 8. Secure the wall mount bracket to the wall with 40 mm M4 screws (GV-Mount205, No. 5) and plain washers (GV-Mount205, No. 7). 9. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Access the live view.
4.5 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Unpack and remove the camera cover with the supplied torx wrench. 2. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 3. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
4 Installing the Fixed IP Dome 4. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 5. Align and secure the camera body with the wall mount bracket with three M3 screws (GVMount900, No. 4). Side A Side B 6. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the wall mount screws to the wall.
7. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Adjust the angle, focus and zoom, and secure the housing cover. See steps 6 to 8 in Hard-Ceiling Mount, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual FD.
4 Installing the Fixed IP Dome 4.6 Wall Box Mount Required accessories: • GV-Mount909 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3).
4. Unpack and remove the camera cover with the supplied torx wrench. 5. Align and secure the camera body to the wall mount bracket with three M3 screws (GVMount909, No. 4). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
4 Installing the Fixed IP Dome 4.7 Wall Pendant Mount Required accessories: • GV-Mount200 • GV-Mount902 The user needs to prepare: • Screws for wall x 4 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. On the installation site, thread the necessary cables and wires from the wall through the pendant tube (GV-Mount200, No. 1), and secure the tube to the wall with 4 screws of your choice.
3. Thread the cables and wires into the dome housing and secure the pendant tube to the end of the housing cap (GV-Mount902, No. 2) with M6 screws (GV-Mount902, No. 4). 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
4 Installing the Fixed IP Dome 4.8 Convex Corner Mount Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount902 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure them with the screw cap (GV-Mount300, No. 6).
3. Secure the pendant tube (GV-Mount200, No. 1) to the plate. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from the front and secure from the backside using plain washers (GV-Mount300, No. 4), split washers (GV-Mount300, No. 5) and the M8 screw caps (GVMount300, No. 6). Backside View 4. Thread the necessary wires and cables through the pendant tube and secure the plate to the wall with 8 self-prepared screws. 5.
4 Installing the Fixed IP Dome 4.9 Convex Corner Box Mount Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount902 The user needs to prepare: • Screws for wall x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure them with the screw cap (GV-Mount300, No. 6). 3. Secure the junction box (GV-Mount203, No. 1) to the mounting plate from the back side using the 25 mm M8 screw (GV-Mount300, No. 3), plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No.
4 Installing the Fixed IP Dome D. Thread the necessary wires and cables through the corrugated tube, plug the tube to the box and secure with part D. Ethernet Power 6. Hinge and hook the pendant tube (GV-Mount203, No. 2) to the junction box. Ethernet Power 7. Thread the wires and cables through the pendant tube into the dome housing and connect them to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GVIPCam H.264 Hardware Manual – FD on the software DVD. 8.
9. Conceal the junction box with M5 screws using the torx wrench (GV-Mount203, No. 5). 10. Refer to the indicated sections of the manuals on the software DVD: A. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. B. Adjust the angle, focus and zoom. See steps 6 and 7 in Hard-Ceiling Mount, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. 11. Put on the housing cover. See 4.1.2 Putting on the Housing Cover.
4 Installing the Fixed IP Dome 4.10 Concave Corner Mount Required accessories: • GV-Mount200 • GV-Mount310 • GV-Mount902 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer, and secure them with the screw cap.
3. Secure the pendant tube (GV-Mount200, No. 1) to the plate. Slide the 30 mm M8 screws (GV-Mount310, No. 2) from the front and secure from the back using plain washers (GVMount310, No. 3), split washers (GV-Mount310, No. 4) and the M8 screw caps (GVMount310, No. 5). Front View Back View 4. Thread the necessary wires and cables through the pendant tube and secure the plate to the wall with 8 self-prepared screws. 5. Connect the network, power and other cables to the camera.
4 Installing the Fixed IP Dome 4.11 Pole Mount Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount902 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing. 2. Secure the pendant tube (GV-Mount200, No. 1) to the mounting bracket (GV-Mount400 / GV-Mount410, No. 1). Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GVMount410, No.
3. Thread the necessary wires and cables through the pendant tube and secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. Ethernet Or Power 4. Thread the wires and cables into the dome housing and connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GVIPCam H.264 Hardware Manual - FD on the software DVD. 5.
4 Installing the Fixed IP Dome 4.12 Pole Box Mount Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount902 The user needs to prepare: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 4.1.1 Assembling the Fixed IP Dome with the Dome Housing.
2. Assemble the mounting bracket (GV-Mount400 / GV-Mount410, No. 1) and the junction box (GV-Mount203, No. 1) from the backside using 25 mm M8 screws (GV-Mount400 / GV-Mount410, No. 4), plain washer (GV-Mount400 / GV-Mount410, No. 5) and split washers (GV-Mount400 / GV-Mount410, No. 6). Backside View 3. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GVMount410, No. 2). Rotate the screw on the strap to adjust its size. Face the conduit exit downward. 4.
4 Installing the Fixed IP Dome D. Thread the necessary wires and cables through the corrugated tube, plug the tube to the box and secure with part D. Ethernet Power 5. Hinge and hook the pendant tube (GV-Mount203, No. 2) to the junction box. Ethernet Power 6. Thread the wires and cables through the pendant tube into the dome housing and connect the network, power and other cables to the camera. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual- FD on the software DVD. 7.
4.13 Power Box Mount Required accessories: • GV-Mount913 The user needs to prepare • Screws for securing the mounting plate to power box 1. Secure the mounting plate (GV-Mount913, No. 1) to the power box with your own screws.
4 Installing the Fixed IP Dome 2. Unpack the camera. 3. Secure the camera to the mounting plate with M3 screws (GV-Mount913, No. 2). Use the holes indicated with “FD” to help you align the camera. 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the cables and wires. See Connecting the Camera, Fixed IP Dome Chapter, GV-IPCam H.264 Hardware Manual - FD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
5. Installing the Fisheye Camera 5.1 Assembling the Fisheye Camera with the Dome Housing Required accessories: • GV-Mount903 1. Align the embossed arrow of the housing cap (GV-Mount903, No. 2) with the arrow inside the dome housing (GV-Mount903, No. 1) and secure them with three M6 screws (GVMount903, No. 4). Tip: The flat hole on the housing cap should be fitted with the hole on the housing cover without any indent.
5 Installing the Fisheye Camera 2. For GV-FE3402 / 3403 / 5302 / 5303 and GV-FER3402 / 3403 / 5302 / 5303, install the camera piers. A. Fasten the camera pier (GV-Mount903, No. 5) into the dome housing (GV-Mount903, No. 1). B. Thread the camera cable through the dome housing and secure the camera to the piers using flat M4 screws (GV-Mount903, No. 6). 3. For GV-FE2301 / 4301 and GV-FER521, place the camera body to the dome housing. Make sure the camera cable is at the top of the dome housing arrow.
4. For GV-FER12203, secure the camera back plate to the dome housing with three M4 screws (GV-Mount903, No. 3) and then secure the camera body onto the back plate. 5. Place the camera cover on the camera and fasten the screws with the supplied torx wrench. For GV-FER12203 and cameras with an IR LED ring, secure its safety lock to the camera and then fasten the screws.
5 Installing the Fisheye Camera 5.2 Straight Tube Box Mount Required accessories: • GV-Mount100 • GV-Mount903 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
1. Assemble the camera to the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Assemble the tube (GV-Mount100, No. 3) and the tube connector (GV-Mount100, No. 4). 3. Thread the camera cable through the tube and secure the tube to the end of the housing cap (GV-Mount903, No.2) with M6 screws (GV-Mount903, No. 4). 4. Thread the camera cable through the box cover (GV-Mount100, No.
5 Installing the Fisheye Camera 5. Secure the junction box (GV-Mount100, No. 1) to the ceiling with 4 self-prepared screws. 6. Assemble the corrugated tube connector (GV-Mount100, No. 6) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 components. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C. Screw part C to the tube. D.
8. Hinge and hook the box cover and secure it with M5 flat screws (GV-Mount100, No. 5). Ethernet Power 9. Access the live view. See 2.1 Installing on a Network, GV-Fisheye IP Camera H.264 User’s Manual on the software DVD.
5 Installing the Fisheye Camera 5.
1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Assemble the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). 3. Thread the camera cable through the tube and secure the tube to the end of the housing cap (GV-Mount903, No.2) with M6 screws (GV-Mount903, No. 4). 4. Thread the camera cable through the mounting bracket (GV-Mount101, No. 1) and assemble the tube with the mounting bracket. 5.
5 Installing the Fisheye Camera 5.4 Wall Mount Bracket 5.4.1 All Models except GV-FER12203 Required accessories: • GV-Mount205 IMPORTANT: GV-FE2303 / 3403 / 4303 / 5303 with the POE converter are not supported. 1. Take the wall mount bracket (GV-Mount205, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert screw anchors (GV-Mount205, No. 6).
3. Align and secure the mounting plate (GV-Mount205, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount205, No. 4). 4. Align and secure the housing plate (GV-Mount205, No. 3) to the mounting plate with 3 M4 screws (GV-Mount205, No. 4). 5. Thread the camera cable through the wall mount bracket as below.
5 Installing the Fisheye Camera 6. Align and secure the camera to the housing plate with 3 M4 screws (GV-Mount205, No. 4). FE VD FD VD FE FD VD VD FE FD Housing Plate 7. Place the camera cover for hard ceiling mount on top of the camera and tighten the screws using the supplied torx wrench. 8. Secure the wall mount bracket to the wall with 40 mm M4 screws (GV-Mount205, No. 5) and plain washers (GV-Mount205, No. 7). 9. Refer to the indicated sections of the GV-Fisheye IP Camera H.
5.4.2 GV-FER12203 GV‐Mount206 Required accessories: • GV-Mount206 1. Take the wall mount bracket (GV-Mount206, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert screw anchors (GV-Mount206, No. 6). 3. Align and secure the mounting plate (GV-Mount206, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount206, No. 4).
5 Installing the Fisheye Camera 4. Align and secure the housing plate (GV-Mount206, No. 3) to the mounting plate with 3 M4 screws (GV-Mount206, No. 4). 5. Secure the back plate of the camera onto the housing plate with 4 M4 screws (GVMount206, No. 4). 6. Thread the camera cable through the wall mount bracket. 7. Align and secure the camera to the back plate.
8. Secure the camera cover using the supplied torx wrench. 9. Secure the wall mount bracket to the wall with 40 mm M4 screws (GV-Mount206, No. 5) and plain washers (GV-Mount206, No. 7). 10. Refer to the indicated sections of the GV-Fisheye IP Camera H.264 User’s Manual on the software DVD to: A. Connect the network, power and other cables to the camera. See 1.7 Connecting the Data Cable. B. Access the live view. See 2.1 Installing on a Network.
5 Installing the Fisheye Camera 5.5 Wall Pendant Mount Required accessories: • GV-Mount200 • GV-Mount903 The user needs to prepare: • Screws for wall x 4 1. Assemble the Fisheye camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Insert the housing cap (GV-Mount903, No. 2) into the wall pendant tube (GV-Mount200, No. 1) and secure the tube to the end of the housing cap (GV-Mount903, No.2) with M6 screws (GV-Mount903, No. 4). 3.
5.6 Tilting Wall Mount Front View Side View: Flat Side View: Tilted Required accessories: • GV-Mount904 IMPORTANT: GV-FER12203 does not support this installation method. 1. Unscrew the inner housing cover using the supplied torx wrench. 2. Assemble the tilting rack (GV-Mount904, No. 3) with the back plate (GV-Mount904, No. 2) and secure them together with 3 short screws (GV-Mount904, No. 5) from the back.
5 Installing the Fisheye Camera 3. Thread the camera cable into an opening on the back plate and align the top side of the camera with the top of the back plate. Tip: Pull the tilting rack to a wider angle for easier threading. 4. Secure the camera from the back with 3 long screws (GV-Mount904, No. 4). 5. Put on the back cover and secure it with 6 short screws (GV-Mount904, No. 5).
6. To accommodate the adjustment, reserve some length of cable by making a curve inbetween the back plate and the back cover. 7. Paste the supplied sticker (GV-Mount904, No. 6) on the wall. The 3 red dots indicate the screw position. Important: Be sure that the “TOP” arrow on the sticker points toward the ceiling. 8. Drill the 3 red dots and insert the supplied plastic screw anchor. 9. Secure the camera to wall using 3 supplied screws. 10. Insert a micro SD card to the camera. 11.
5 Installing the Fisheye Camera 5.7 Convex Corner Mount Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Thread the camera cable through the wall pendant tube (GV-Mount200, No. 1), and secure the tube to the end of the housing cap (GV-Mount903, No.2) with M6 screws (GVMount903, No. 4).
3. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6). 4. Thread the camera cable and secure the pendant tube to the plates. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from the front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GVMount300, No. 6). Backside View 5.
5 Installing the Fisheye Camera 5.8 Convex Corner Box Mount Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No.
3. Secure the junction box (GV-Mount203, No. 1) to the mounting plates from the backside using the 25 mm M8 screw (GV-Mount300, No. 3), plain washer (GV-Mount300, No. 4), and split washer (GV-Mount300, No. 5). Back View 4. Secure the mounting plates to the wall with 8 self-prepared screws. Face the conduit exit downward. 5. Assemble the corrugated tube connector (GV-Mount203, No. 4) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts.
5 Installing the Fisheye Camera 6. Thread the camera cable through the wall pendant tube (GV-Mount203, No. 2), and secure the tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 7. Hinge and hook the pendant tube to the junction box. Ethernet Power 8. Connect the network, power and other cables to the camera. See 1.7 Connecting the Data Cable, GV-Fisheye IP Camera H.264 User’s Manual on the software DVD. 9. Conceal the box with M5 screws (GV-Mount203, No.
5.9 Concave Corner Mount Required accessories: • GV-Mount200 • GV-Mount310 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
5 Installing the Fisheye Camera 3. Thread the camera cable through the wall pendant tube (GV-Mount200, No. 1), and secure the tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 4. Thread the camera cable and secure the pendant tube to the plates. Slide the 30 mm M8 screws (GV-Mount903, No. 2) from the front and secure from the backside using plain washer (GV-Mount903, No. 3), split washer (GV-Mount903, No. 4) and secure with M8 screw cap (GV-Mount903, No. 5).
5.10 Pole Mount Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount903 1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Secure the mounting bracket (GV-Mount400 / GV-Mount410, No. 1) to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size.
5 Installing the Fisheye Camera 3. Thread the camera cable through the pendant tube (GV-Mount200, No. 1) and secure the tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 4. Thread the camera cable through the mounting bracket and secure the pendant tube to the bracket. Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No.
5.11 Pole Box Mount Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount903 Required accessories: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 5.1 Assembling the Fisheye Camera with the Dome Housing. 2. Secure the junction box (GV-Mount203, No. 1) to the mounting bracket (GV-Mount400 / GV-Mount410, No. 1) from the backside using 25 mm M8 screws (GV-Mount400 / GVMount410, No. 4), plain washer (GV-Mount400 / GV-Mount410, No.
5 Installing the Fisheye Camera 3. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GVMount410, No. 2). Rotate the screw on the strap to adjust its size. Face the conduit exit downward. 4. Assemble the corrugated tube connector (GV-Mount203, No. 4) with the self-prepared corrugated tube. A. Dismantle the supplied corrugated tube connector. You should have 4 parts. A B C D B. Slide part A and part B to the self-prepared corrugated tube. A+B C D C.
5. Thread the camera cable through the pendant tube (GV-Mount203, No. 2) and secure the tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 6. Hinge and hook the pendant tube to the junction box. Ethernet Power 7. Connect the network, power and other cables to the camera. See 1.7 Connecting the Data Cable, GV-Fisheye IP Camera H.264 User’s Manual on the software DVD. 8. Conceal the junction box with M5 screws (GV-Mount203, No.
5 Installing the Fisheye Camera 5.12 Power Box Mount Required accessories: • GV-Mount912 The user needs to prepare • Screws for securing the mounting plate to power box 1. Secure the mounting plate (GV-Mount912, No. 1) to the power box with your own screws.
2. For GV-FER12203: A. Thread the camera cable through the camera back plate, the mounting plate, and the power box. B. Secure the back plate and the mounting plate with M3 screws (GV-Mount912, No. 2). Use the holes labeled as “FE/FER”. C. Align the camera with the back plate and tighten the screws. D. Secure the camera cover. 3. For other models, thread the camera cable through the mounting plate and the power box, and secure the camera to the mounting plate with M3 screws (GV-Mount912, No. 2).
6 Installing the GV-IP Speed Dome 6. Installing the GV-IP Speed Dome 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube 6.1.1 GV-SD220-S / GV-SD2300 Required Item • GV-SD220-S / 2300 standard package 1. Insert the desiccants to the camera. A. Remove the camera cover using the supplied hex key.
B. Insert two desiccant packs to indicated positions. IMPORTANT: Be sure the desiccant is concealed in the GV-IP Speed Dome within 2 minutes of opening the desiccant pack. C. Follow step 1 to secure the camera cover with the supplied hex key. Make sure the first two screws to be tightened are diagonal to each other. 2. Assemble the camera with the pendant tube. A. Thread the camera data cable through the pendant tube. B. Rotate the camera and lock it to the pendant tube. C.
6 Installing the GV-IP Speed Dome 6.1.2 GV-SD2301 / GV-SD2411 Required Item • GV-SD2301 / 2411 standard package 1. Insert the desiccants to the camera. A. Remove the camera cover using the supplied hex key.
B. Insert one desiccant pack to the indicated place. IMPORTANT: Be sure the desiccant is concealed in the GV-IP Speed Dome within 2 minutes of opening the desiccant pack. C. Insert your SD card into the SD card slot. D. Secure the camera cover with the supplied hex key. Make sure the first two screws to be tightened are diagonal to each other. 2. Connect the cables to the camera. A. Thread the Ethernet cable and the data cable through the pendant tube.
6 Installing the GV-IP Speed Dome B. Remove the cap and the mounting plate at the back of the camera. C. Insert the Ethernet cable to the LAN port on the camera. D. Slide the cap and components through the Ethernet cable as shown below. It is recommended to use the supplied RJ-45 connector.
E. Move the cap and the components toward the LAN port. F. Secure the cap tightly. G. Slip the rubber ring on the Data Cable and then pass the pin connectors of the Data Cable through the mounting plate. The rubber ring The Data Cable H. Fasten the data cable with the mounting plate and the rubber ring.
6 I. Installing the GV-IP Speed Dome Insert the pin connectors of the Data Cable to the indicated area. J. Secure the mounting plate with the supplied hex key. 3. Assemble the camera with the pendant tube. A. Secure the safety lock. B. Push the rivets into the holes on the pendant tube and rotate clockwise to lock the position.
C. Tighten the screws with the supplied hex key. D. Secure the pendant tube to the wall with self-prepared screws.
6 Installing the GV-IP Speed Dome 6.2 In-Ceiling Mount 6.2.1 GV-SD220 This installation method is only applicable to indoor GV-IP Speed Dome (GV-SD220). The thickness of the ceiling board must not exceed 4 cm (1.57 in). Required Items • GV-Mount907 The user needs to prepare: • ceiling screws x 3 1. Assemble the support racks, mounting plate and the mounting ring. A. Secure the three support racks (GV-Mount907, No. 1) to the mounting ring (GVMount907, No.
C. Secure the mounting plate with the support racks with screws (GV-Mount907, No. 3). Make sure the arrows on the mounting ring and mounting plate are aligned. 2. Secure the lock plate to the GV-IP Speed Dome. A. Unscrew the screw on the side of the camera body with the supplied hex key (GVMount907, No. 6). B. Secure the lock plate (GV-Mount907, No. 7) to the camera body with the supplied screw (GV-Mount907, No. 7).
6 3. Installing the GV-IP Speed Dome Assemble the GV-IP Speed Dome to the assembly done in step 1. D C lock plate indent A B A. Thread the camera data cable under the indent of the mounting ring. B. Hook the camera from the underside. C. Align the lock plate on the camera to the indent of the mounting ring. The camera should lie completely on the mounting plate. D. Rotate the camera to lock and secure the lock plate with the supplied screw. 4. Paste the installation sticker (GV-Mount907, No.
6.2.2 GV-SD220-S / GV-SD2300 This installation method is only applicable to GV-SD220-S and GV-SD2300. The complete installation weights 6.75 kg / 14.88 lb. Make sure the chosen ceiling can bear the weight, but the thickness of the ceiling board must not exceed 3.5 cm (1.38 in). Required Items • GV-Mount908 1. Assemble the housing cap (GV-Mount908, No. 1) with the mounting plate (GVMount908, No. 2) with 4 screws (GV-Mount908, No. 3).
6 Installing the GV-IP Speed Dome 2. Remove the camera dome. 3. Secure the camera with the assembled mounting plate. A. Put 2 screws (GV-Mount908, No. 4) loosely on the opposite sides of the camera. B. Thread the camera data cable through the mounting plate and the housing cap. C. Rotate the camera so that the screws lodge in the housing cap at the indicated position. D. Put on another 2 screws (GV-Mount908, No. 4) and use the hex key (GV-Mount908, No.5) to secure all 4 screws tightly.
4. Drill the ceiling. Use the installation sticker (GV-Mount908, No. 6) to help you estimate the size of the camera. 5. Thread the camera data cable through the ceiling and insert the camera. Adjust the 4 screws to clip the camera tightly to the ceiling. 6. Secure the in-ceiling cover (GV-Mount908, No. 7) with 2 screws (GV-Mount908, No. 8) using the hex key (standard package). 7. Connect the network, power and other cables to the camera. See 1.
6 Installing the GV-IP Speed Dome 6.2.3 GV-SD2301 / GV-SD2411 This installation method is only applicable to GV-SD2301 and GV-SD2411. The complete installation weights 6.1 kg / 13.4 lb. Make sure the chosen ceiling can bear the weight, but the thickness of the ceiling board must not exceed 3.5 cm (1.38 in). Required Items • GV-Mount908-2 1. Assemble the housing cap (GV-Mount908-2, No. 1) with the mounting plate (GVMount908-2, No. 2) with 4 screws (GV-Mount908-2, No. 5).
2. Assemble the mounting cap to the mounting plate by rotating the mounting cap onto the housing cap. Put on 2 screws (GV-Mount908-2, No. 6) and use the hex key (GVMount908-2, No.7) to secure both screws tightly. 3. Remove the camera dome. 4. Drill the ceiling. Use the installation sticker (GV-Mount908-2, No. 9) to help you estimate the size of the camera. 5. Thread the camera data cable through the ceiling and insert the camera. Rotate the camera onto the mounting cap. 6.
6 7. Installing the GV-IP Speed Dome Secure the in-ceiling cover (GV-Mount908-2, No. 4) with 2 screws (GV-Mount908-2, No. 8) using the hex key (camera’s standard package). 8. Connect the network, power and other cables to the camera. See 1.6 Connecting the Camera, GV-IP Speed Dome User’s Manual on the software CD/DVD.
6.3 Straight Tube Box Mount 6.3.1 GV-SD220-S / GV-SD2300 This installation method is only applicable to GV-SD220-S and GV-SD2300. Required accessories: • GV-Mount100 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
6 Installing the GV-IP Speed Dome 1. Follow step 1 in 6.1.1 GV-SD220-S / GV-SD2300 to insert the desiccant packs. 2. Remove the tube connector from the pendant tube with the supplied hex key. Save the M6 screws for later use. Tube connector 3. Secure the tube connector to the dome. A. Assemble the tube connector with the dome and rotate the tube connector to lock it with the dome. B. Secure the tube connector with the supplied M6 screws. 4. Assemble the tube (GV-Mount100, No.
6. Follow steps 3 to 6 in 5.2 Straight Tube Box Mount to secure the tube and the junction box. 7. Connect the network, power and other cables to the camera. See 1.6 Connecting the Camera, GV-IP Speed Dome User’s Manual on the software CD/DVD. 8. Hinge and hook the box cover and secure it with M5 flat screws (GV-Mount100, No. 5).
6 Installing the GV-IP Speed Dome 6.3.2 GV-SD2301 / GV-SD2411 This installation method is only applicable to GV-SD2301 and GV-SD2411. Required accessories: • GV-Mount102 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
1. Follow step 1 in 6.1.2 GV-SD2301 / GV-SD2411 to insert the desiccant packs and the SD card. 2. Secure the supporting plate (GV-Mount102, No. 3) to the ceiling with the 4 self-prepared screws. 3. Fasten the 4 M8 (20 mm) screws (GV-Mount102, No. 11) to the back of the junction box (GV-Mount102, No. 1). 4. Hang the junction box onto the supporting plate. Slide the junction box sideway to lodge the 4 screws with the plate.
6 Installing the GV-IP Speed Dome 5. Fasten the 4 screws in the holes of the junction box using the supplied No. 6 torx wrench (GV-Mount102, No. 9). 6. Assemble the corrugated tube connector with the self-prepared corrugated tube. A. Dismantle the corrugated tube connector from the junction box. You should have 3 components. B. Slide the corrugated tube connector to the self-prepared corrugated tube. C. Screw part B to the tube. D. Connect the corrugated tube to the box and secure with part C. E.
7. Hinge and hook the box cover to the junction box. 8. Based on the sizes of the cables, thread the Ethernet cable(s) through the small-size or middle-size holes of the waterproof rubber (GV-Mount102, No. 12). Cut a line through the biggest hole of the waterproof rubber, and thread the camera data cable through the hole. 9. Embed the waterproof rubber onto the top of the junction box.
6 Installing the GV-IP Speed Dome 10. Assemble the tube (GV-Mount102, No. 6), the housing cap (GV-Mount102, No. 5), and the box cover plate (GV-Mount102, No. 4) by rotating the parts together. 11. Make sure the tubes are properly screwed. Tighten the screws using the supplied No. 2 torx wrench (GV-Mount102, No. 8). 12. Thread the network, power and other cables (including the cables connected through the waterproof rubber) through the tube, and connect the tube with the camera. 13.
15. Secure the box cover by fastening the 2 screws at the corner with No. 6 torx wrench.
6 Installing the GV-IP Speed Dome 6.4 Straight Tube Mount 6.4.1 GV-SD220-S / GV-SD2300 This installation method is only applicable to GV-SD220-S and GV-SD2300.
1. Follow steps 1 to 3 in 6.1.1 GV-SD220-S / GV-SD2300 to insert the desiccant. 2. Remove the tube connector from the pendant tube with the supplied hex key. Tube connector 3. Secure the tube connector to the dome. A. Assemble the tube connector with the dome and rotate the tube connector to lock it with the dome. B. Secure the tube connector with the supplied M6 screws. 4. Assemble the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). 5.
6 Installing the GV-IP Speed Dome 6. Follow steps 4 to 6 in 5.3 Straight Tube Mount to assemble the mounting bracket and secure the dome to the ceiling. 7. Connect the network, power and other cables to the camera. See 1.6 Connecting the Camera, GV-IP Speed Dome User’s Manual on the software CD/DVD.
6.4.2 GV-SD2301 / GV-SD2411 GV-Mount702 GV-Mount103 This installation method is only applicable to GV-SD2301 and GV-SD2411. Required accessories: • GV-Mount103 The user needs to prepare: • Screws for ceiling x 4 Optionally extend with: • GV-Mount702 1. 1. Follow steps 1 to 3 in 6.1.2 GV-SD2301 / GV-SD2411 to insert the desiccant packs and the SD card.
6 Installing the GV-IP Speed Dome 2. Assemble the tube (GV-Mount103, No. 3), the housing cap (GV-Mount103, No. 2), and the mounting bracket (GV-Mount103, No. 1) by rotating the parts together. 3. Make sure the tubes are properly screwed. Tighten the screws using the supplied torx wrench (GV-Mount103, No. 4). 4. Thread the network, power and other cables (including the cables connected through the waterproof rubber) through the tube. 5. Connect the network, power and other cables to the camera. See 1.
6.5 Convex Corner Mount GV-SD220-S / GV-SD2300 GV-SD2301 / GV-SD2411 This installation method is only applicable to outdoor GV-IP Speed Dome. Required accessories: • Pendant Tube (in outdoor IP Speed Dome standard package) • GV-Mount300 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the pendant tube. See 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube. 2. Follow steps 3 to 5 in 5.
6 Installing the GV-IP Speed Dome 6.6 Convex Corner Box Mount 6.6.1 GV-SD220-S / GV-SD2300 This installation method is only applicable to GV-SD220-S and GV-SD2300. Required accessories: • GV-Mount203 • GV-Mount300 The user needs to prepare: • Screws for wall x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Follow steps 2 to 5 in 5.8 Convex Corner Box Mount to assemble the mounting plates, box and corrugated tube and secure them to the wall. 2. Follow step 1 in 6.
3. Remove the tube connector from the pendant tube with the supplied hex key. Save the M6 screws for later use. Tube connector 4. Secure the tube connector to the dome. A. Assemble the tube connector with the dome and rotate the tube connector to lock it with the dome. B. Secure the tube connector with the supplied M6 screws. 5. Thread the camera data cable through the wall pendant tube (GV-Mount203, No. 2), and assemble the dome housing and the tube with M6 screws.
6 Installing the GV-IP Speed Dome 6. Hinge and hook the pendant tube to the junction box. n et r Ether Powe 7. Connect the network, power and other cables to the camera. See 1.6 Connecting the Camera, GV-IP Speed Dome User’s Manual on the software CD/DVD.
6.6.2 GV-SD2301 / GV-SD2411 This installation method is only applicable to GV-SD2301 and GV-SD2411. Required accessories: • GV-Mount501 • GV-Mount300 The user needs to prepare: • Screws for ceiling x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Follow step 1 in 6.1.2 GV-SD2301 / GV-SD2411 to insert the desiccant packs and the SD card. 2.
6 Installing the GV-IP Speed Dome 3. Follow steps 3 to 9 in 6.3.2 GV-SD2301 / GV-SD2411 to set up the cables and assemble the junction box. 4. Follow steps 2 to part c of step 3 in 6.1.2 GV-SD2301 / GV-SD2411 to connect the camera cables and assemble the camera with the pendant tube. 5. Secure pendant tube onto the junction box with the 4 supplied M8 (30 mm) screws (GVMount501, No. 5) and 4 plain washers (GV-Mount501, No. 9). 6. Secure the box cover by fastening the 2 screws at the corner with No.
6.7 Concave Corner Mount GV-SD220-S / GV-SD2300 GV-SD2301 / GV-SD2411 This installation method is only applicable to outdoor GV-IP Speed Dome. Required accessories: • Pendant Tube (in outdoor IP Speed Dome standard package) • GV-Mount310 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the pendant tube. See 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube. 2. Follow steps 2, 4 and 5 in 5.
6 Installing the GV-IP Speed Dome 6.8 Pole Mount GV-SD220-S / GV-SD2300 GV-SD2301 / GV-SD2411 This installation method is only applicable to outdoor GV-IP Speed Dome. Required accessories: • Pendant Tube (in outdoor IP Speed Dome standard package) • GV-Mount400 or GV-Mount410 1. Assemble the camera with the pendant tube. See 6.1 Assembling Outdoor IP Speed Dome with Pendant Tube. 2. Follow step 2 in 5.10 Pole Mount to secure the pole mount bracket. 3. Follow step 4 in 5.
6.9 Pole Box Mount 6.9.1 GV-SD220-S / GV-SD2300 This installation method is only applicable to GV-SD220-S and GV-SD2300. Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 Required accessories: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Follow step 1 in 6.1.1 GV-SD220-S / GV-SD2300 to insert the desiccant. 2. Follow steps 2 to 4 in 5.11 Pole Box Mount to install the junction box, mounting bracket and corrugated tube.
6 Installing the GV-IP Speed Dome 3. Remove the tube connector from the pendant tube with the supplied hex key. Save the M6 screws for later use. Tube connector 4. Secure the tube connector to the dome. A. Assemble the tube connector with the dome and rotate the tube connector to lock it with the dome. B. Secure the tube connector with the supplied M6 screws. 5. Thread the camera data cable through the pendant tube (GV-Mount203, No. 2) and secure them together with M6 screws. 6. Follow step 6 in 5.
6.9.2 GV-SD2301 / GV-SD2411 GV-Mount501 GV-Mount400 or GV-Mount410 This installation method is only applicable to GV-SD2301 and GV-SD2411. Required accessories: • GV-Mount501 • GV-Mount400 or GV-Mount410 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Follow step 1 in 6.1.2 GV-SD2301 / GV-SD2411 to insert the desiccant packs and the SD card.
6 Installing the GV-IP Speed Dome 2. Connect the supporting plate of GV-Mount501 to GV-Mount400 or GV-Mount410 by fastening the 4 M8 30mm screws and plain washers (supplied with GV-Mount400 or GVMount410), and fasten the 4 M8 (30 mm) screws and plain washers. 3. Follow steps 3 to 9 in 6.3.2 GV-SD2301 / GV-SD2411 to set up the cables and assemble the junction box. 4. Follow steps 2 to 3-c in 6.1.2 GV-SD2301 / GV-SD2411 to connect the camera cables and assemble the camera with the pendant tube. 5.
Note for Closing the Bullet Camera Cover To ensure that the camera performs its full capacity against water and dust, tightly close and lock the camera cover as indicated below.
7 Installing the Bullet / Target Bullet / LPR Camera 7. Installing the Bullet / Target Bullet / LPR Camera Besides the Bullet Camera Series, the installation methods in Chapter 7 only apply to GVEBL2101 of the Target Bullet Camera Series, and GV-LPC2211 / LPC2011 of the IP LPR Camera Series. 7.
1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6). 2. For GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E, loosen the indicated screws to remove the base and the back plate. Back Plate Note: To see how to thread the cables into the camera, refer to Installation, Bullet Camera (II) Chapter, GV-IPCam H.264 Hardware Manual – BL.
7 Installing the Bullet / Target Bullet / LPR Camera 3. Assemble the camera or the back plate with the mounting plates. GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E: From the front, align the back plate with the mounting plates and insert the M4 screws. From the back, secure the M4 screw using the nuts and plates. The M4 screws, nuts and plates come with the camera packing list.
GV-EBL2101: From the front, insert the screw for mounting kit (supplied with GVEBL2101). From the backside, secure using the nut for mounting (supplied with GVEBL2101). Front View Back View 4. For GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E, re-attach the camera back to the back plate. 5. Secure the mounting plates to the wall with 8 self-prepared screws. 6. Refer to the indicated sections of the manuals on the software DVD: A.
7 Installing the Bullet / Target Bullet / LPR Camera 7.2 Concave Corner Mount GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E Other GV-Bullet Camera Models, GVEBL2101 and GV-LPC2211 / LPC2011 Required accessories: GV-Mount310 The user needs to prepare: Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No.
2. For GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E, loosen the indicated screws to remove the base and the back plate. Back Plate Note: To see how to thread the cables into the camera, refer to Installation, Bullet Camera (II) Chapter, GV-IPCam H.264 Hardware Manual – BL. 3. Assemble the camera or the back plate with the mounting plates.
7 Installing the Bullet / Target Bullet / LPR Camera Other GV-Bullet Camera models: From the front, align the M5 split washer (GVMount310, No. 8) and insert the M5 screws (GV-Mount310, No. 6). From the backside, secure using M5 plain washer (GV-Mount310, No. 7) and M5 screw cap (GV-Mount310, No. 9). Front View Back View GV-EBL2101: From the front, insert the screw for mounting kit (supplied with GVEBL2101). From the backside, secure using the nut for mounting (supplied with GVEBL2101).
5. Secure the mounting plates to the wall with 8 self-prepared screws. 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Bullet Camera Chapter, GV-IPCam H.264 Hardware Manual - BL. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Adjust the angle, focus and zoom of the camera.
7 Installing the Bullet / Target Bullet / LPR Camera 7.3 Pole Mount GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E Other GV-Bullet Camera Models, GVEBL2101 and GV-LPC2211 / LPC2011 Required accessories: GV-Mount400 or GV-Mount410 1. For GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E, loosen the indicated screws to remove the base and the back plate.
2. Assemble the camera or the back plate with the mounting bracket. GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E: From the front, align the back plate with the mounting plates and insert the M4 screws. From the back, secure the M4 screw using the nuts and plates. The M4 screws, nuts and plates come with the camera packing list. Front View Back View Other GV-Bullet Camera models: From the front, align the M5 split washer (GVMount400 / GV-Mount410, No.
7 Installing the Bullet / Target Bullet / LPR Camera GV-EBL2101: From the front, insert the screw for mounting kit (supplied with GVEBL2101). From the backside, secure using the nut for mounting (supplied with GVEBL2101). Front View Back View 3. For GV-BL1501 / 2501 / 3401 / 1511 / 2511 / 3411 / 5311 and GV-BL2511-E / 5311-E, re-attach the camera back to the back plate. 4. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GVMount410, No. 2).
Note for Installing the Box Camera The GV-Housing101 support indoor or outdoor installation of GV-BX Series.
8 Installing the Box Camera 8. Installing the Box Camera 8.1 Assembling Box Camera with the Housing Box Required accessories: • GV-Housing101 (with heater and fan) The user needs to prepare: • Ethernet, power, audio and I/O cables, etc for the camera • Silicon rubber to seal the camera • Mini USB cable with the connector of dimensions 9.6 x 7.6 mm or below for the camera (Optional) • Power wires for power board on the GV-Housing101 (24V AC / 12V DC input) 1. Unscrew the housing box (GV-Housing101, No.
2. Open the housing box, loosen the four screws and remove the black plate. 3. Remove the two black caps and the stoppers from the bottom of housing box. Black Cap Stopper 4. Thread all the required cables through the supporting tube (GV-Housing101, No. 2) and then the two black caps as below. To ensure later installation, allocate the cables to the two black caps properly. Note: 1. You need to use an Ethernet cable without RJ-45 connector to go through the housing box. 2.
8 Installing the Box Camera 5. Thread the cables through the holes at the bottom of the housing box and install the RJ-45 connector on the Ethernet cable. 6. Assemble the short screw (GV-Housing101, No. 5) with M5 plain washer (GV-Housing101, No. 7) and secure the camera on the black plate. Front View Back View with Camera 7. Line up the black plate with the four screws, slide it forward to adjust the camera’s position as desired and tighten the screws.
8. Connect all the required cables to the camera and the power board. Power Adapter Connector Power Board Note: Make sure the Power Adapter wires are connected to the correspondent electrodes labeled on the power board. Note this is only for the Power Adapter from GeoVision. If you are using different power adapter, the wires may have different colors. ․ Black wire: negative electrode ․ Black with white stripes wire: positive electrode 9. Tighten the black cap on the bottom of housing box.
8 Installing the Box Camera 11. Mark the installation site, drill four holes and secure the housing box to the wall using the supplied screw anchors (GV-Housing101, No. 3), M5 screws (GV-Housing101, No. 4) and four plain washers (GV-Housing101, No. 6). 12. Adjust the camera to ensure proper live view: A. Access the live view of the camera. For the models supporting varifocal lens, check if the housing box cover is on the scene when adjusting the camera.
8.2 Convex Corner Mount Required accessories: • GV-Mount300 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
8 Installing the Box Camera 2. Assemble the housing box with the mounting plates: A. Thread the camera cables through the mounting plates. B. Slide the 20 mm M5 screws (GV-Mount300, No. 4) from front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GV-Mount300, No. 6). 3. Secure the plates to the wall with 8 self-prepared screws.
8.3 Concave Corner Mount Required accessories: • GV-Mount310 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
8 Installing the Box Camera 2. Assemble the camera with the mounting plates. A. Thread the camera cable through the mounting plates. B. Slide the 20 mm M5 screws (GV-Mount310, No. 2) from front and secure from the backside using plain washer (GV-Mount310, No. 3), split washer (GV-Mount310, No. 4) and screw cap (GV-Mount300, No. 5). 3. Secure the plates to the wall with 8 self-prepared screws.
8.4 Pole Mount Required accessories: • GV-Mount400 or GV-Mount410 1. Assemble the camera with the mounting bracket (GV-Mount400 / GV-Mount410, No.1). A. Thread the camera cables through the mounting bracket. B. Slide the 20 mm M5 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 9), split washer, (GV-Mount400 / GV-Mount410, No. 10) and M5 screw cap (GV-Mount400 / GV-Mount410, No. 11).
8 Installing the Box Camera 2. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GVMount410, No. 2). Rotate the screw on the strap to adjust its size.
9. Installing the Arctic Box / IP LPR Camera 9.1 Convex Corner Mount Required accessories: GV-Mount300 The user needs to prepare: Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure with the screw cap (GV-Mount300, No. 6).
9 Installing the Arctic Box / IP LPR Camera 2. Assemble the camera with the mounting plates. A. Thread the camera cable through the mounting plates. B. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from front and secure from the backside using plain washer (GV-Mount300, No. 4), split washer (GV-Mount300, No. 5) and screw cap (GV-Mount300, No. 6). Backside View 3. Secure the plates to the wall with 8 self-prepared screws. 4. Refer to the indicated sections of the manuals on the software DVD: A.
9.2 Concave Corner Mount Required accessories: GV-Mount310 The user needs to prepare: Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
9 Installing the Arctic Box / IP LPR Camera 2. Assemble the camera with the mounting plates. A. Thread the camera cable through the mounting plates. B. Slide the 30 mm M8 screws (GV-Mount310, No. 2) from front and secure from the backside using plain washer (GV-Mount310, No. 3), split washer (GV-Mount310, No. 4) and screw cap (GV-Mount300, No. 5). Front View Back View 3. Secure the plates to the wall with 8 self-prepared screws. 4.
9.3 Pole Mount Required accessories: GV-Mount400 or GV-Mount410 1. Assemble the camera with the mounting bracket (GV-Mount400 / GV-Mount410, No.1). A. Thread the camera cable through the mounting bracket. B. Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GV-Mount410, No. 5), split washer, (GV-Mount400 / GV-Mount410, No. 6) and M8 screw cap (GVMount400 / GV-Mount410, No. 7).
9 Installing the Arctic Box / IP LPR Camera 2. Secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GVMount410, No. 2). Rotate the screw on the strap to adjust its size. 3. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to PoE. See Connecting the Camera, IR Arctic Box Camera Chapter, GV-IPCam H.264 Hardware Manual - BXE. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
10. Installing the Mini Fixed Dome 10.1 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2). 3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later.
10 Installing the Mini Fixed Dome 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Align and secure the camera to the wall mount bracket with two M3 screws (GVMount900, No. 4). 6. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the wall mount screws to the wall. 7. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera.
10.2 Wall Box Mount Required accessories: • GV-Mount909 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3). 4. Unscrew the camera’s cover using the supplied torx wrench.
10 Installing the Mini Fixed Dome 5. Align and secure the camera to the wall mount bracket with two M3 screws (GVMount909, No. 4). 6. Refer to the indicated sections of the manuals on the software DVD: A. Thread the network, power and other cables through the wall mount bracket and connect them to the camera. See Connecting the Camera, Mini Fixed Dome & Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - MFD. B. Access the live view.
10.3 Wall Mount Bracket GV-Mount918 Required accessories: • GV-Mount918 IMPORTANT: GV-Mount918 is not compatible with GV-MFD120 / 130 / 220 / 320 / 520. 1. Take the wall mount bracket (GV-Mount918, No. 1) and make 2 marks on the wall for screw anchors. 2. Drill the marks and insert 2 screw anchors (GV-Mount918, No. 2). 3. Secure the wall mount bracket to the wall with 2 wall mount screws (GV-Mount918, No. 3) and 2 plain washers (GV-Mount918, No. 5).
10 Installing the Mini Fixed Dome Note: Thread the network, power and other cables through the wall mount bracket before securing the wall mount bracket to the wall. 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Align and secure the camera to the wall mount bracket with 2 M3 screws (GV-Mount918, No. 4). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera.
10.4 Power Box Mount Required accessories: • GV-Mount910 or GV-Mount913 The user needs to prepare • Screws for securing the mounting plate to power box 1. Secure the mounting plate (GV-Mount910 or GV-Mount913, No. 1) to the power box with your own screws.
10 Installing the Mini Fixed Dome GV-Mount913 D A C C A B B EFD UFD MDR FD UFD FD MFD MFD MDR B C D C Type of Power Box Hole 4’’ Square A Double Gang B 4’’ Octagon C Single Gang D B EFD A A 2. Remove camera cover with the supplied torx wrench. 3. Secure the camera to the mounting plate with M3 screws (GV-Mount910 or GVMount913, No. 2). Use the holes indicated with MFD. 4. Refer to the indicated sections of the manuals on the software DVD: A.
C. Based on the live view, adjust the pan and tilt angles and secure the housing cover with the torx wrench. See steps 7 to 11 in Installation, GV-MFD Series, Mini Fixed Dome & Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual MFD.
11. Installing the Mini Fixed Rugged Dome 11.1 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Align and secure the camera to the wall mount bracket with two M3 screws (GVMount900, No. 4).
11 Installing the Mini Fixed Rugged Dome 6. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the wall mount screws to the wall. 7. Refer to the indicated sections of the manuals on the software DVD: A. Waterproof the cable with the supplied cable connector. See step 6 in Installation, GV-MDR Series, Mini Fixed Dome & Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - MDR. B. Connect the network and power to the camera.
11.2 Wall Box Mount . Required accessories: • GV-Mount909 IMPORTANT: The GV-Mount909 is not IP66 protected. Make sure you install the camera in a dry place. 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3).
11 Installing the Mini Fixed Rugged Dome 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Thread the cable through the wall mount bracket and secure the camera to the wall mount bracket with two M3 screws (GV-Mount909, No. 4). Use the labels on the wall mount bracket to help you. 6. Refer to the indicated sections of the manuals on the software DVD: A. Waterproof the cable with the supplied cable connector.
11.3 Wall Mount Bracket Required accessories: • GV-Mount918 IMPORTANT: When the Mini Fixed Rugged Dome camera is installed with GV-Mount918, it is not compatible with the Waterproof Connector. Ø27 mm (1.06'') 1. Take the wall mount bracket (GV-Mount918, No. 1) and make 2 marks on the wall for screw anchors.
11 Installing the Mini Fixed Rugged Dome 2. Drill the marks and insert 2 screw anchors (GV-Mount918, No. 2). 3. Secure the wall mount bracket to the wall with 2 wall mount screws (GV-Mount918, No. 3) and 2 plain washers (GV-Mount918, No. 5). Note: Thread the network, power and other cables through the wall mount bracket before securing the wall mount bracket to the wall. 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Connect the network, power and other cables to the camera.
11.4 Power Box Mount Required accessories: • GV-Mount910 or GV-Mount913 The user needs to prepare • Screws for securing the mounting plate to power box 1. Secure the mounting plate (GV-Mount910 or GV-Mount913, No. 1) to the power box with your own screws.
11 Installing the Mini Fixed Rugged Dome GV-Mount913 D A C C A B B EFD UFD MDR FD UFD FD MFD MFD MDR B C D C Type of Power Box Hole 4’’ Square A Double Gang B 4’’ Octagon C Single Gang D B EFD A A 2. Open the camera cover with the supplied torx wrench. 3. Thread the camera cable through the mounting plate and the power box, and secure the camera to the mounting plate with M3 screws (GV-Mount910 or GV-Mount913, No. 2). Use the holes indicated with “MDR”. 4.
B. Connect the network and power to the camera. See Connecting the Camera, Mini Fixed Dome & Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - MDR. C. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. D. Based on the live view, adjust the angle of the camera. See step 8 in Installation, GV-MDR Series, Mini Fixed Dome & Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - MDR. E.
12 Installing the Target (Mini) Fixed Dome 12. Installing the Target (Mini) Fixed Dome 12.1 L-Shaped Wall Mount GV‐Mount900 GV-EFD1100 / 2100 GV-EFD2101 / 3101 Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 4. Open the camera housing cover. z For GV-EFD1100 / EFD2100, open the camera housing cover by turning. z For GV-EFD2101 / EFD3101, use the torx wrench to loosen three screws on housing cover and remove the camera housing. Next, unscrew the three screws to separate the back plate as indicated below. 5.
12 Installing the Target (Mini) Fixed Dome z GV-EFD2101 / EFD3101: Use the holes labeled as UFD to secure the back plate, and then reattach the camera back to the back plate. 6. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the wall mount screws to the wall. 7. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.
12.2 Wall Box Mount GV‐Mount909 GV-EFD1100 / EFD2100 GV-EFD2101 / EFD3101 Required accessories: • GV-Mount909 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. wall 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3).
12 Installing the Target (Mini) Fixed Dome 4. Open the camera housing cover. z For GV-EFD1100 / EFD2100, open the camera housing cover by turning. z For GV-EFD2101 / EFD3101, use the torx wrench to loosen three screws on housing cover and remove the camera housing. 5. Align and secure the camera to the wall mount bracket with two M3 screws (GVMount909, No. 4). z GV-EFD1100 / EFD2100: Use the holes labeled as EFD. z GV-EFD2101 / EFD3101: Use the holes labeled as FD.
6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover. See Installation, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD.
12 Installing the Target (Mini) Fixed Dome 12.3 Wall Mount Bracket GV-Mount918 This installation method is only applicable to GV-EFD1100 and GV-EFD2100. Required accessories: • GV-Mount918 1. Take the wall mount bracket (GV-Mount918, No. 1) and make 2 marks on the wall for screw anchors. 2. Drill the marks and insert 2 screw anchors (GV-Mount918, No. 2). 3. Secure the wall mount bracket to the wall with 2 wall mount screws (GV-Mount918, No. 3) and 2 plain washers (GV-Mount918, No. 5).
4. Open the camera’s cover by turning. 5. Align and secure the camera to the wall mount bracket with 2 M3 screws (GV-Mount918, No. 4). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the network, power and other cables to the camera. See Connecting the Camera, Target Mini Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
12 Installing the Target (Mini) Fixed Dome 12.
1. Secure the mounting plate (GV-Mount910 or GV-Mount913, No. 1) to the power box with your own screws.
12 Installing the Target (Mini) Fixed Dome 2. Open the camera housing cover. z For GV-EFD1100 / EFD2100, open the camera housing cover by turning. z For GV-EFD2101 / EFD3101, use the torx wrench to loosen three screws on housing cover and remove the camera housing. If you are installing GV-Mount910, unscrew the three screws to separate the back plate as indicated below. 3. Secure the camera / back plate to the mounting plate with M3 screws (GV-Mount910 or GV-Mount913, No. 2).
4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover. See Installation, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD.
12 Installing the Target (Mini) Fixed Dome 12.5 GV-EFD2101 / EFD3101 In-Ceiling Mount This installation method is only applicable to GV-EFD2101 and GV-EFD3101. The thickness of the ceiling board must not exceed 4 cm (1.57 in). Required accessories: • GV-Mount915 1. Assemble the support racks, mounting plate and the mounting ring. A. Secure two brackets (GV-Mount915, No. 1) to the in-ceiling plate (GV-Mount915, No.2) with a black screw (GV-Mount915, No. 5).
B. Assemble the in-ceiling ring (GV-Mount915, No. 4). Make sure the arrows on the mounting ring and mounting plate are aligned. C. Assemble the third bracket and secure it with a black screw (GV-Mount915, No. 5). D. Secure the brackets on the underside of the in-ceiling ring with black screws (GVMount915, No. 5). E. Use the thread lock (GV-Mount915, No. 9) to attach the in-ceiling cover with the inceiling ring using the screw (GV-Mount915, No. 7).
12 Installing the Target (Mini) Fixed Dome 2. Use the torx wrench to loosen three screws on housing cover of the camera, and remove the camera housing. 3. Paste the sticker (GV-Mount915, No. 8) to the ceiling, and then cut off the circle part of the ceiling. 4. Place the mounting casing inside the ceiling hole, and secure the casing with the ceiling. A. Turn the plastic clip of the bracket outward. B. Tighten the bracket so that the plastic clips are tightly pinching the ceiling board.
6. Place the camera onto the in-ceiling plate, and secure with screws (GV-Mount915, No. 6). Be sure to align the arrow on the camera back plate with the arrow on the in-ceiling ring. 7. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
12 Installing the Target (Mini) Fixed Dome 12.6 Assembling GV-EFD2101 / EFD3101 with Dome Housing This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount917 1. Use the torx wrench to loosen three screws on housing cover and remove the camera housing.
2. Secure the housing plate to the dome housing with M4 small screws (GV-Mount917, No. 3). 3. Secure the camera body to the housing plate (GV-Mount917, No. 3) with three M4 small screws (GV-Mount917, No. 4).
12 Installing the Target (Mini) Fixed Dome 12.7 Wall Pendant Mount GV‐Mount200 GV‐Mount917 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount200 • GV-Mount917 The user needs to prepare: • Screws for wall x 4 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing.
2. Thread the camera cables from the wall through the pendant tube (GV-Mount200, No. 1), and secure the pendant tube to the end of the housing cap (GV-Mount917, No. 2) with M6 screws (GV-Mount917, No. 4). 3. Secure the wall pendant tube to the wall with 4 self-prepared screws. 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B.
12 Installing the Target (Mini) Fixed Dome 12.8 Straight Tube Mount GV‐Mount101 GV‐Mount101 GV‐Mount702 GV‐Mount917 GV‐Mount917 This installation method is only applicable to GV-EFD2101 and GV-EFD3101.
1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Assemble the mounting bracket (GV-Mount101, No. 1), the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). Tighten with the supplied torx wrench (GV-Mount101, No. 4) 3. Thread the cables and wires into the dome housing. 4. Secure the tube to the end of the housing cap (GV-Mount902, No. 2) with M6 screws (GV-Mount101, No. 4). 5.
12 Installing the Target (Mini) Fixed Dome 12.9 Straight Tube Box Mount GV‐Mount100 GV‐Mount100 GV‐Mount917 GV‐Mount702 GV‐Mount917 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount100 • GV-Mount917 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Follow steps 2 to 6 in 4.2 Straight Tube Box Mount to install the junction box, corrugated tube and mounting tube. 3. Thread the wires and cables through the housing cap (GV-Mount917, No. 2) and secure the tube to the end of the housing cap with M6 screws (GV-Mount917, No. 4). 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network.
12 Installing the Target (Mini) Fixed Dome 12.10 Convex Corner Mount GV‐Mount200 GV‐Mount917 GV‐Mount300 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount917 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No.
3. Secure the pendant tube (GV-Mount200, No. 1) to the plate. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from the front and secure from the backside using plain washers (GV-Mount300, No. 4), split washers (GV-Mount300, No. 5) and the M8 screw caps (GVMount300, No. 6). Backside View 4. Thread the necessary wires and cables through the pendant tube and secure the plate to the wall with 8 self-prepared screws. 5. Thread the wires and cables into the dome and connect them to the camera. 6.
12 Installing the Target (Mini) Fixed Dome 12.11 Convex Corner Box Mount GV‐Mount203 GV‐Mount300 GV‐Mount917 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount917 The user needs to prepare: • Screws for wall x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Follow steps 2 to 6 in 4.
5. Conceal the junction box with M5 screws using the torx wrench (GV-Mount203, No. 5). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover.
12 Installing the Target (Mini) Fixed Dome 12.12 Concave Corner Mount GV‐Mount200 GV‐Mount917 GV‐Mount310 Required accessories: • GV-Mount200 • GV-Mount310 • GV-Mount917 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Follow steps 2 and 3 in 4.10 Concave Corner Mount to assemble the mounting plates and the pendant tube. 3.
B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover. See Installation, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD.
12 Installing the Target (Mini) Fixed Dome 12.13 Pole Mount GV‐Mount200 GV‐Mount917 GV‐Mount400 or GV‐Mount410 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount917 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Secure the pendant tube (GV-Mount200, No. 1) to the mounting bracket (GV-Mount400 / GV-Mount410, No. 1).
3. Thread the necessary wires and cables through the pendant tube and secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. Ethernet or Power 4. Thread the wires and cables into the dome housing and connect them to the camera. 5. Secure the pendant tube to the end of the housing cap (GV-Mount917, No. 2) with M6 screws (GV-Mount917, No. 4). 6. Refer to the indicated sections of the manuals on the software DVD: A.
12 Installing the Target (Mini) Fixed Dome 12.14 Pole Box Mount GV‐Mount203 GV‐Mount917 GV‐Mount400 or GV‐Mount410 This installation method is only applicable to GV-EFD2101 and GV-EFD3101. Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount917 The user needs to prepare: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 12.6 Assembling the GV-EFD2101 / EFD3101 with the Dome Housing. 2. Follow steps 2 to 5 in 4.
5. Conceal the junction box with M5 screws (GV-Mount203, No. 3) using the torx wrench (GV-Mount203, No. 5). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target (Mini) Fixed Dome Chapter, GV-IPCam H.264 Hardware Manual - EFD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C.
13. Installing the Target Mini Fixed Rugged Dome 13.1 L-Shaped Wall Mount Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Unscrew the three screws as indicated below. A back plate can be separated from the bottom. 6. Align and secure the back plate to the wall mount bracket with two M3 screws (GVMount900, No. 4). Use the holes indicated with MDF.
13 Installing the Target Mini Fixed Rugged Dome 7. Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward. Tighten the wall mount screws to the wall. 8. Refer to the indicated sections of the manuals on the software DVD: A. Finish installing the camera. Follow steps 5 to 15 in Installation, Target Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - EDR. B. Connect the network and power cables to the camera.
13.2 Wall Box Mount Required accessories: • GV-Mount909 1. Take the wall mount bracket (GV-Mount909, No. 1) and make 4 marks on the wall for screw anchors. wall 2. Drill the marks and insert 4 screw anchors (GV-Mount909, No. 2). 3. Secure the wall mount bracket to the wall with wall mount screws (GV-Mount909, No. 3). 4. Unscrew the camera’s cover using the supplied torx wrench.
13 Installing the Target Mini Fixed Rugged Dome 5. Unscrew the three screws as indicated below. A back plate can be separated from the bottom. 6. Align and secure the back plate to the wall mount bracket with two M3 screws (GVMount909, No. 4). Use the holes indicated with MFD. 7. Refer to the indicated sections of the manuals on the software DVD: A. Finish installing the camera. Follow steps 5 to 15 in Installation, Target Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - EDR. B.
13.3 Wall Mount Bracket Required accessories: • GV-Mount918 1. Take the wall mount bracket (GV-Mount918, No. 1) and make 2 marks on the wall for screw anchors. 2. Drill the marks and insert 2 screw anchors (GV-Mount918, No. 2). 3. Secure the wall mount bracket to the wall with 2 wall mount screws (GV-Mount918, No. 3) and 2 plain washers (GV-Mount918, No. 5). Note: Thread the network, power and other cables through the wall mount bracket before securing the wall mount bracket to the wall.
13 Installing the Target Mini Fixed Rugged Dome 4. Unscrew the camera’s cover using the supplied torx wrench. 5. Unscrew the camera using the supplied torx wrench, and separate the camera from the back plate. 6. Align and secure the camera’s back plate to the wall mount bracket with 6 M3 screws (GV-Mount918, No. 4).
7. Connect the network, power and other cables to the camera. Align and secure the camera to the wall mount bracket. 8. Refer to the indicated sections of the manuals on the software DVD: A. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. B. Based on the live view, adjust the pan and tilt angles. See steps 14 in Installation, Target Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual EDR. C.
13 Installing the Target Mini Fixed Rugged Dome 13.4 Power Box Mount Required accessories: • GV-Mount910 or GV-Mount913 The user needs to prepare • Screws for securing the mounting plate to power box 1. Secure the mounting plate (GV-Mount910 or GV-Mount913, No. 1) to the power box with your own screws.
GV-Mount913 D A C C A B B EFD UFD MDR FD UFD FD MFD MFD MDR B C D C Type of Power Box Hole 4’’ Square A Double Gang B 4’’ Octagon C Single Gang D B EFD A A 2. Remove camera cover with the supplied torx wrench. 3. Unscrew the three screws as indicated below. A back plate can be separated from the bottom.
13 Installing the Target Mini Fixed Rugged Dome 4. Secure the back plate to the mounting plate with M3 screws (GV-Mount910 or GVMount913, No. 2). Use the holes indicated with MFD. 5. Refer to the indicated sections of the manuals on the software DVD: A. Finish installing the camera. Follow steps 5 to 15 in Installation, Target Mini Fixed Rugged Dome Chapter, GV-IPCam H.264 Hardware Manual - EDR. B. Connect the network and power cables to the camera.
14. Installing the Target Vandal Proof IP Dome 14.1 L-Shaped Wall Mount GV‐Mount900 Required accessories: • GV-Mount900 1. Take the wall mount bracket (GV-Mount900, No. 1) and make 2 marks on the wall for screw anchors. wall 2. Drill the marks and insert 2 screw anchors (GV-Mount900, No. 2).
14 Installing the Target Vandal Proof IP Dome 3. Insert the wall mount screws (GV-Mount900, No. 3) and leave enough distance (approximately 2 mm) to hang the wall mount bracket later. 2 mm Long Screw Wall 4. Open the camera housing cover, remove the back plate and thread the cables into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GVIPCam H.264 Hardware Manual - EVD on the software DVD. 5.
8. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target Vandal Proof IP Dome Chapter, GV-IPCam H.264 Hardware Manual - EVD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover. See step 10 in Installation, Target Vandal Proof IP Dome Chapter, GV-IPCam H.
14 Installing the Target Vandal Proof IP Dome 14.2 Wall Mount Bracket GV‐Mount206 Required accessories: • GV-Mount206 1. Take the wall mount bracket (GV-Mount206, No. 1) and make 4 marks on the wall for screw anchors. 2. Drill the marks and insert 4 screw anchors (GV-Mount206, No. 6). 3. Align and secure the mounting plate (GV-Mount206, No. 2) to the wall mount bracket with 4 M4 screws (GV-Mount206, No. 4).
4. Align and secure the housing plate (GV-Mount206, No. 3) to the mounting plate with 3 M4 screws (GV-Mount206, No. 4). 5. Open the camera housing cover, remove the back plate and thread the cables into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GVIPCam H.264 Hardware Manual - EVD on the software DVD. 6. Align and secure the camera’s back plate to the housing plate with four M4 screws (GVMount206, No. 4). 7.
14 Installing the Target Vandal Proof IP Dome 14.3 In-Ceiling Mount The thickness of the ceiling board must not exceed 4 cm (1.57 in). Required accessories: • GV-Mount916 1. Assemble the support racks, mounting plate and the mounting ring. A. Secure two brackets (GV-Mount916, No. 1) to the in-ceiling plate (GV-Mount916, No.2) with a black screw (GV-Mount916, No. 5).
B. Assemble the in-ceiling ring (GV-Mount916, No. 4). Make sure the arrows on the mounting ring and mounting plate are aligned. C. Assemble the third bracket and secure it with a black screw (GV-Mount916, No. 5). D. Secure the brackets on the underside of the in-ceiling ring with black screws (GVMount916, No. 5). E. Use the thread lock (GV-Mount916, No. 9) to attach the in-ceiling cover with the inceiling ring using the M3 short screw (GV-Mount916, No. 7).
14 Installing the Target Vandal Proof IP Dome 2. Open the camera housing cover and remove the back plate. 3. Place the back plate onto the in-ceiling plate, and secure with screws (GV-Mount916, No. 6). The arrow on the in-ceiling ring should be pointing away from the cable opening of the back plate. 4. Paste the sticker (GV-Mount916, No. 8) to the ceiling, and then cut off the circle part of the ceiling. 5. Place the mounting casing inside the ceiling hole, and secure the casing with the ceiling. A.
B. Tighten the bracket so that the plastic clips are tightly pinching the ceiling board. Plastic clip turned outward Ceiling 6. Thread the cables through the in-ceiling mount and into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GV-IPCam H.264 Hardware Manual - EVD on the software DVD. 7. Secure the camera to the back plate with the supplied torx wrench. 8. Refer to the indicated sections of the manuals on the software DVD: A.
14 Installing the Target Vandal Proof IP Dome 14.4 Assembling Dome Housing Required accessories: • GV-Mount903 1. Open the camera housing cover, remove the back plate and thread the cables into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GVIPCam H.264 Hardware Manual - EVD on the software DVD. 2. Secure the back plate to the dome housing with M4 screws (GV-Mount903, No. 3).
14.5 Wall Pendant Mount GV‐Mount200 GV‐Mount903 Required accessories: • GV-Mount200 • GV-Mount903 The user needs to prepare: • Screws for wall x 4 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing.
14 Installing the Target Vandal Proof IP Dome 2. Thread the camera cables from the wall through the pendant tube (GV-Mount200, No. 1), and secure the pendant tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 3. Secure the wall pendant tube to the wall with 4 self-prepared screws. 4. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network.
14.
14 Installing the Target Vandal Proof IP Dome 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Assemble the mounting bracket (GV-Mount101, No. 1), the tube (GV-Mount101, No. 2) and the tube connector (GV-Mount101, No. 3). Tighten with the supplied torx wrench (GV-Mount101, No. 4) 3. Secure the tube to the end of the housing cap (GV-Mount902, No. 2) with M6 screws (GV-Mount101, No. 4). 4. Secure the housing bracket to the ceiling with 4 self-prepared screws. 5.
14.7 Straight Tube Box Mount GV‐Mount100 GV‐Mount100 GV‐Mount903 GV‐Mount702 GV‐Mount903 Required accessories: • GV-Mount100 • GV-Mount903 The user needs to prepare: • Screws for ceiling x 4 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.
14 Installing the Target Vandal Proof IP Dome 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Follow steps 2 to 6 in 4.2 Straight Tube Box Mount to install the junction box, corrugated tube and mounting tube. 3. Thread the wires and cables through the housing cap (GV-Mount903, No. 2) and secure the tube to the end of the housing cap with M6 screws (GV-Mount903, No. 4). 4. Refer to the indicated sections of the manuals on the software DVD: A.
14.8 Convex Corner Mount with Pendant Tube GV‐Mount200 GV‐Mount300 GV‐Mount903 Required accessories: • GV-Mount200 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure them with the screw cap (GV-Mount300, No. 6).
14 Installing the Target Vandal Proof IP Dome 3. Secure the pendant tube (GV-Mount200, No. 1) to the plate. Slide the 30 mm M8 screws (GV-Mount300, No. 2) from the front and secure from the backside using plain washers (GV-Mount300, No. 4), split washers (GV-Mount300, No. 5) and the M8 screw caps (GVMount300, No. 6). Backside View 4. Thread the necessary wires and cables through the pendant tube and secure the plate to the wall with 8 self-prepared screws. 5.
14.9 Convex Corner Mount with Wall Bracket GV‐Mount300 GV‐Mount900 Required accessories: • GV-Mount300 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount300, No. 1), slide in the plain washer (GVMount300, No. 4), then the split washer (GV-Mount300, No. 5), and secure them with the screw cap (GV-Mount300, No. 6).
14 Installing the Target Vandal Proof IP Dome 2. Open the camera housing cover, remove the back plate and thread the cables into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GVIPCam H.264 Hardware Manual - EVD on the software DVD. 3. Align and secure the back plate with the L-shaped mount with four M5 screws (GVMount900, No. 5). Use the holes labeled as VD. 4. Secure the camera to the back plate with the supplied torx wrench. 5.
14.10 Convex Corner Box Mount GV‐Mount203 GV‐Mount300 GV‐Mount903 Required accessories: • GV-Mount203 • GV-Mount300 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Follow steps 2 to 6 in 4.9 Convex Corner Box Mount to install the mounting plates, junction box, corrugated tube and pendant tube. 3.
14 Installing the Target Vandal Proof IP Dome 4. Secure the pendant tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 5. Conceal the junction box with M5 screws using the torx wrench (GV-Mount203, No. 5). 6. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target Vandal Proof IP Dome Chapter, GV-IPCam H.264 Hardware Manual - EVD. B. Access the live view.
14.11 Concave Corner Mount with Pendant Tube GV‐Mount200 GV‐Mount903 GV‐Mount310 Required accessories: • GV-Mount200 • GV-Mount310 • GV-Mount903 The user needs to prepare: • Screws for wall x 8 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Follow steps 2 and 3 in 4.10 Concave Corner Mount to assemble the mounting plates and the pendant tube. 3.
14 Installing the Target Vandal Proof IP Dome 5. Refer to the indicated sections of the manuals on the software DVD: A. Connect the camera to power and network. See Connecting the Camera, Target Vandal Proof IP Dome Chapter, GV-IPCam H.264 Hardware Manual - EVD. B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover.
14.12 Concave Corner Mount with Wall Bracket GV‐Mount310 GV‐Mount900 Required accessories: • GV-Mount310 • GV-Mount900 The user needs to prepare: • Screws for wall x 8 1. Assemble the mounting plates (GV-Mount310, No. 1), slide in the plain washer (GVMount310, No. 3), then the split washer (GV-Mount310, No. 4), and secure them with the screw cap (GV-Mount310, No. 5).
14 Installing the Target Vandal Proof IP Dome 2. Open the camera housing cover, remove the back plate and thread the cables into the camera. See steps 1 to 6 in Installation, Target Vandal Proof IP Dome Chapter, GVIPCam H.264 Hardware Manual - EVD on the software DVD. 3. Align and secure the back plate with the L-shaped mount with four M5 screws (GVMount900, No. 5). Use the holes labeled as VD. 4. Secure the camera to the back plate with the supplied torx wrench. 5.
14.13 Pole Mount GV‐Mount200 GV‐Mount400 or GV‐Mount410 GV‐Mount903 Required accessories: • GV-Mount200 • GV-Mount400 or GV-Mount410 • GV-Mount903 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Secure the pendant tube (GV-Mount200, No. 1) to the mounting bracket (GV-Mount400 / GV-Mount410, No. 1). Slide the 30 mm M8 screws (GV-Mount400 / GV-Mount410, No. 3) from the front and secure from the backside using plain washer (GV-Mount400 / GVMount410, No.
14 Installing the Target Vandal Proof IP Dome 3. Thread the necessary wires and cables through the pendant tube and secure the mounting bracket to the pole using 3 steel straps (GV-Mount400 / GV-Mount410, No. 2). Rotate the screw on the strap to adjust its size. Ethernet or Power 4. Thread the wires and cables into the dome housing. 5. Secure the pendant tube to the end of the housing cap (GV-Mount903, No. 2) with M6 screws (GV-Mount903, No. 4). 6.
14.14 Pole Box Mount GV‐Mount203 GV‐Mount400 or GV‐Mount410 GV‐Mount903 Required accessories: • GV-Mount203 • GV-Mount400 or GV-Mount410 • GV-Mount903 The user needs to prepare: • Corrugated tube x 1 (3/4’’, ø 26.0 ~ 26.5 mm) 1. Assemble the camera with the dome housing. See 14.4 Assembling the Dome Housing. 2. Follow steps 2 to 5 in 4.12 Pole Box Mount to install the junction box, mounting bracket, corrugated tube and pendant tube. 3.
14 Installing the Target Vandal Proof IP Dome B. Access the live view. See Accessing the Live View, Getting Started Chapter, GVIPCam H.264 Firmware Manual. C. Based on the live view, adjust the pan and tilt angles and secure the housing cover. See step 10 in Installation, Target Vandal Proof IP Dome Chapter, GV-IPCam H.264 Hardware Manual – EVD.
