Owner Manual

ManualsBrandsGeorge Oliver Manuals5 Piece Kitchen & Dining Room SetsEshaan 4 - Person Solid Wood Dining Set

Label Picture Description QTY

A Chair Back 1

B Front Leg 1

Warning: These chairs are intended only for normal use with all four legs on

the ground. These chairs have relatively thin legs and are not designed to

be sat in with only two legs on the ground (as from tipping back, forward, or

to the side), and such can cause stress and failure of one or more of the

legs. Any misuse of the chairs voids any warranties, expressed or implied.

Assembly Instructions

Caution: You must read this before you proceed

Dining Chair

Part List

Page 1 of 8

Summary of content (8 pages)

PAGE 1
Assembly Instructions Caution: You must read this before you proceed Dining Chair Warning: These chairs are intended only for normal use with all four legs on the ground. These chairs have relatively thin legs and are not designed to be sat in with only two legs on the ground (as from tipping back, forward, or to the side), and such can cause stress and failure of one or more of the legs. Any misuse of the chairs voids any warranties, expressed or implied.
PAGE 2
C Side Stretcher (L) 1 D Side Stretcher (R) 1 E Side Rail (L) 1 F Side Rail (R) 1 G Cushion Seat 1 Description QTY ① JCBC M6 x 50mm + S/W M6 + F/W M6 x 13mm 5 ② Allen Key M4 1 ③ FH Screw #8x32mm 5 ④ L-Bracket 5 ⑤ Csk Screw M3.
PAGE 3
Assembly Preparation Before Beginning Assembly: Assembly Steps Overview Chair Back (A) Cushion Seat (G) Side Stretcher (D) Side Stretcher (C) Front Leg (B) Side Rail (F) Side Rail (E) This Dining Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Dining Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
PAGE 4
Step 1 1.2 (C) Has a small hole for identification. 1.1 1.1) Insert the Side Stretcher(C) and Side Stretcher(D) into the Chair Back(A) as shown. Note: Side Stretcher(C) has a small hole for identification. 1.2) Attach Side Stretcher(C) and Side Stretcher(D) to Chair Back(A) using Bolts(①) with Allen Key(②). Do not fully tighten the Bolts. Step 2 2.2 2.1 (E) Has a small hole for identification. 2.1) Insert the Side Rail(E) and Side Rail(F) into Chair Back(A).
PAGE 5
Step 3 3.1 3.2 Insert Front Leg(B) onto the Side Stretchers and Side Rails as shown. 3.1) Attach Front Leg(B) to Side Stretchers using Bolts(①) with Allen Key(②). 3.2) Attach Front Leg(B) to Side Rails using Screws(③) with Screwdriver(⑥). Do not fully tighten the Bolts or Screws. Step 4 4.2 4.1 G 4.1) Align the Cushion Seat(G) to Chair Back(A) as pictured. 4.2) Then, ensure the Cushion Seat(G) is centered using the front view, as shown.
PAGE 6
Step 5 Front Leg 5.1 5.2 Back Leg Place the Chair on the edge of a table as shown. 5.1) Attach L-Brackets(④) to Side Stretchers using Screws(⑤) with Screwdriver(⑥). 5.2) Attach L-Brackets(④) to Cushion Seat(E) using Screws(⑤) with Screwdriver(⑥). Do not fully tighten the Screws.
PAGE 7
Place the Dining Chair on a Level Surface to check for wobbles. If it wobbles lift the Dining Chair some 30cm to 50cm high from the ground, keep your feet and toes well away from the drop zone, and drop the Dining Chair freely and vertically with the four legs, hitting the ground at the same time. This Drop Test will help ensure that all parts and gaps reach full alignment status. Test again for evenness on a Level Surface.
PAGE 8
Care & Maintenance Page 8 of 8