Model 52600 System Settings and User Notes The World Leader in Subsurface Imaging™ Geophysical Survey Systems, Inc. Tel 603.893.1109 • Fax 603.889.3984 sales@geophysical.com www.geophysical.
Copyright© 2001, 2007 Geophysical Survey Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form Published by Geophysical Survey Systems, Inc. 12 Industrial Way Salem, New Hampshire 03079 Printed in the United States GSSI, RADAN, and SIR are registered trademarks of Geophysical Survey Systems, Inc.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Limited Warranty, Limitations Of Liability And Restrictions Geophysical Survey Systems, Inc. hereinafter referred to as GSSI, warrants that for a period of 24 months from the delivery date to the original purchaser this product will be free from defects in materials and workmanship.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes FCC Notice (for U.S. Customers): This device complies with part 15, class F of the FCC Rules: Operation is subject to the following conditions: 1. This device many not cause harmful interference, and 2.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes For U.S. Customers Ground Penetrating Radar Coordination Notice And Equipment Registration Note: This form is only for Domestic United States users. The Federal Communications Commission (FCC) requires that all users of GPR who purchased antennas after July 15th, 2002 register their equipment and areas of operation.
Geophysical Survey Systems, Inc. 6. Model 52600 Antenna System Settings and User Notes Equipment Identification: Brand Name: Geophysical Survey Systems, Inc. Antenna Model No.: CHECK all antennas being registered. Model 7.
Geophysical Survey Systems, Inc. Do not send this information to GSSI.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Certificate To Whom it may concern: This is to certify that electromagnetic radiation emissions from transducers (antenna with transmitting and receiving electronics) manufactured by Geophysical Survey Systems, Inc. (GSSI) DO NOT constitute a safety or health hazard to operating personnel.
Geophysical Survey Systems, Inc. This page intentionally left blank.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Table Of Contents Model 52600 Antenna.................................................................................................... 1 System Setup - Standard Settings .............................................................................. 1 Signal Position.................................................................................................... 1 Gain Check...........................................
Geophysical Survey Systems, Inc.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Model 52600 Antenna Thank you for purchasing a Model 52600 antenna. The Model 52600 represents the current state of the art in high resolution concrete structure imaging. The Model 52600 antenna has greatly improved resolution over previous high frequency antennas. Not only is the frequency higher, but the antenna has the ability to see objects at very close distances.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Gain Check The surface pulse should be about 2/3 the width of the screen. If it is greater, reduce the Gains manually. If the signal appears too small you can manually increase the Gains, but the first gain point should never exceed 10dB. Minicart Your Model 52600 is designed to fit into the Model 614 or Model 615 minicart.
Geophysical Survey Systems, Inc.
Geophysical Survey Systems, Inc. Model 52600 Antenna System Settings and User Notes Specifications Center frequency: 2600 MHz Pulse duration: 0.4 ns Depth of penetration: 0-12 inches depending on type of concrete Size of sensor: 1.5 x 4 x 6.5 inches (3.8 x 10 x 16.5 cm) The 52600 controller box has two brackets to mount the box to the extension handle. The thumbscrews are provided with the SIR-3000. The connector with the red circle is for the control cable (direct to the SIR-3000).