=220 7RWDO 6WDWLRQ 0DQXDO 0
Total Station Manual Preface Thanks a lot for purchasing our total station! This manual is your good helper, please read it carefully before using the instrumentand keep it safely. Product affirms: In order to get the best service from our company, please feedback your instruments’ versionincludingnumber, purchasing date and your suggestions to us after the purchasing of the product.
Total Station Manual z Features: Rich Feature: Our Total Station is equipped with a wealth of measurement applications including data storage, parameter settings and other functions for a 1. Absolute coded dial With absolute digital dial, instrumentscan be measureddirectlywhen it powers on. The measured azimuth angle result will not be lost even when the instrument shut off. 2. powerful memory management Large-capacity EMS memory,easy to manage the file system, serving to add, delete and transfer data 3.
Total Station Manual NOTE: Avoid look directly into the sun with the eyepiece when measuring. Recommended to use solar filter to reduce the impact 1. Avoid extreme temperature when storing equipment and sudden changes in temperature when using the instrument. 2. The instrument should be loaded in boxplaced in dry and ventilated place and prevented from shock, dust and moisture when it is not in use. 3. 4. 5. 6. 7. 8. 9. 10.
Total Station Manual z Security Guide Pay attention to the following safety matters when you use the laser ranging free of prism. Warning: Total station fit out laser level 3R/ċa which is recognized by the loge, which is above: the verticallocking screw saying “3A laser product ”.This product belongs to Class 3R levellaser .According to the following standards IEC 60825-1 2001Class 3R/ċ a laser product can reachfive times of emission limits of the Class 2/ Ċ in the wavelength between 400nm-700nm.
Total Station Manual Harmful Distance is the maximum distance from the starting point of the laser beams to where people are right safe.The built-in harmful idstance of the Class 3R/ċa laser is 1000m(3300ft) and the laser intensity will reduce to that of Class 1 products (which does not harm eyes) if people is out of this range.
Total Station Manual Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Total Station Manual CONTENTS 1. 2. Name and function of eachpart............................................................................. 11 1. Name.............................................................................................................. 11 2. Keys Functions and information display........................................................13 Preparation before measurement...........................................................................14 1. 2. 3. 4. 5. 6. 7. 3. 4.
Total Station Manual 3. NP/P Toggle....................................................................................................47 4. Height Transfer...............................................................................................47 5. 6. 7. 8. 9. Hidden Point...................................................................................................51 Free Coding....................................................................................................
Total Station Manual 11.2 11.3 Inverse............................................................................................ 110 Bearing-Bearing Intersection......................................................... 113 11.4 11.5 11.6 11.7 11.8 Bearing-Distance Intersection........................................................ 115 Distance-Distance Intersection.......................................................118 Line-Line Intersection.........................................................
Total Station Manual 9. 2. EDM Setting.................................................................................................189 Adjust and Tools..................................................................................................190 1. Adjust........................................................................................................... 190 1.1 View adjust parameters.................................................................. 190 1.2 Adjust Index Error.............
Total Station Manual 1. Name and function of eachpart 1. Name +DQGOH 22EMHFWLYH EMHFWWL YH 2SWLFDO VLJKW 2S SWLFDO VLJKW +RRUL]RQWDO +RUL]RQWDO PRWLRQ FODPS PR RWLRQ FODPS . .H\SDG G 6FUHHQ +RRUL]RQWDO +RUL]RQWDO WWDQJHQW VFUHZ WD DQJHQWW VFUHZ 11
Total Station Manual +DQGOH VFUHZ )RFXVLQJ NQRE +RUL]RQWDO D[LV FHQWHU (\HSLHFH 9HUWLFDO PRWLRQ FODPS /2*2 9HUWLFDO 7DQJHQW VFUHZ 56 & SRUW /HYHOOLQJ VFUHZ 6XEVWUDWH 12
Total Station Manual 2. Keys Functions and information display Key Function Power ON/ Power OFF. MEAS Trigger key, depends on setting, maybe disting& save, disting or none. ESC Cancel or exit. ENT Confirm or commit editing. Switch pages Hot key to enter function menu in measuring interface. User defined function key 1. User defined function key 2 Ʒ Move cursor up or goto previous. ͩ Move cursor down or goto next. Move cursor left or goto left. Move cursor right or goto right.
Total Station Manual 2. Preparation before measurement 1. Unpack and store instrument z Unpack Put down the box gently and turn up the cover then turn on the lock, open the cover and take out the instrument. z Deposit Cover up the telescope mirror and make the vertical motion of alidade upwards then put the instrument horizontally (keep the objective upwards) into box. Then screw vertical motion gently. Cover up the box cover andlock the box.
Total Station Manual ĸ Rotate instrument 90°by vertical axis, then use foot screw C to center the bubble. ĹRepeatsteps above until the bubble is at the same place in all directions. 2. Centering by centering tool ( optional or laser ) 1) Set up a tripod Extend a tripod to the appropriate height make sure the legs are spaced at equal intervals and the head is approximately level .Set the tripod so that the head is positioned over the surveying point. Brace tripod on the ground and keep one leg fixed.
Total Station Manual aim at station accurately. Tighten the center connection screw and leveling instrument accurately again. This operation should be repeated till the plumb aims at station accurately. 3. About the battery z Mounting the battery ƿFully charge the battery before measurement. ƿCut off the power before removing the battery. ⾥ Step mounting the battery 1. Insert the battery to the instrument. 2. Press the top of the battery until you hear a click sound. ⾥ Step Remove battery 1.
Total Station Manual z completely. Charge the battery once a month no matter if it is used to prolong its longevity. 4. Reflecting prism When using a prism mode for measuring distance, reflection prism should be placed where the target is. A reflecting prism group includes one or three prisms that can connect prism group placed at the base of the tripod with the dock connector or by placing them in the stem directly. Prism group may need to be configured by users based on target. 5.
Total Station Manual Number input box: In number input box, user can only input numbers, include “1-9”,“.”, “-+”. Number will appear in box when user presses the key. Text input box: In text input box, user can input numbers and letters. Repeat pressing same key to get proper letter, such as A->B->C->7. When right-bottom of screen display icon AB, user can input number/letter; when display icon 01, user can only input number.
Total Station Manual 2 Press ƻ key 1, key 2, key 3. Then press key F4, [1],[2],[3],[F4 active text input ] mode.Icon AB should appear in right bottom screen. 3 Press ƻ key 7, display letter ‘A’, wait about half second, press key 7 twice, display letter ‘B’, then [A],[B],[V],[ press key 2, display letter 2] ‘V’, wait about half a second, press key 2 four times, display number ‘2’. Then finished text ‘123ABV2’ input. 4 ƻ Press key ENT to finish editing, cursor will [ENT] move down to next input box.
Total Station Manual 2 Press key F1(Delete). ƻ [F1] 3 Press key ENT to confirm ƻ [ENT] input. Press Key ESC to [ESC] undo changes. 8. Point Search Point search is a function used by applications to find measured or fixed points in the jobs.DŽ Point search is limited to a particular job. If several points meet the search criteria, then the results are ordered according to the date. 8.
Total Station Manual 2 ƻ In searching result window, using arrow key Ė Ė Ę to move cursor to select Ę [F4] [ENT] point number. Press key F4 or ENT to conirm selecting. Soft keys introduction: [View] Show the coordinate of selected point. 3 Using arrow key Ė Ę ƻ to move cursor and select point number. Press key F1 to show the coordinate details of selected point. [F1] 4 Press ƻ ESC or F4 back to [ESC] [F4] previous screen. [Coord.] Input point manually.
Total Station Manual 4 Input point number and N, ƻ E, Z values, by pressing ENT [ENT] to move cursor to next input box. 5 After ƻ all values finishing input, pressing key F4 to save the point to the job. [F4] [Job]Choose another job’s points. 3 If required point not exists ƻ in the job, user can choose [F3] another job’s points. 4 ƻ Entering job list by [F1] pressing key F1, choose the [F4] particular job and press ENT [ENT] or F4 to commitchoosing. 5 Entering ƻ searching point number.
Total Station Manual 6 Press key F4 to search the ƻ [F4] point in the selected job. Ć1[F2](Zero): Set N, E, Z to 0. [F3](Coord.): Input point manually. [OK] Commit selected point. 8.2 Wildcard search The wildcard search is indicated by a “*”. The asterisk is a place holder for any following sequence of characters. Wildcards should be used if the point number is not fully known, or to search for a batch of points. Examples: * All points are found.
Total Station Manual 3. Q-Survey 1. Notes in the distance measurement After the placement of instrumentand turned on the power, total station is ready, can start measuring. In measurement display, user can call the function of set key, the functionkeys and hotkey. The show is an example. Localized version may be slightly different.
Total Station Manual When start the distance measurement, EDM will measure distance for the object in the light path.If there are temporary obstacles in the light path (such as by car, or the heavy rain, snow, or filled with fog), the distance measured by EDM is the distance to the nearest obstacle. When a long distance measurement, laser beam deviation of collimation line will affect the accuracy of measurement.
Total Station Manual 2. EDM Setting 2.1 Set the mode of EDM Select the mode of distance measurement,there Single,Repeat,Tracking,3 Times,4 Times,5 Times. Steps 1 Press ƻ Key are 6 modes : Display [F4]( Ę )and show the second soft key in the [F4] Q-Surveying. Press [F3] to [F3] enter the interface of EDM Setting. 2 ƻ When the cursor is in EDM mode option,Press the direction key of ĕė to select ĕ the mode of ė measurement.Each time you press ĕ or ė , the mode of measurement is switched.
Total Station Manual refer to “Technical Parameters”. Steps 1 ƻ Key Display After entering to the interface of EDM Setting,using the direction of Ę Ę to move the cursor to the setting item of Reflector. 2 Press ƻ ĕ ė to select the types of reflector. Each time ĕ you press ĕ or ė , the type of ė reflector is switched. 3 ƻ After finished setting, press [F3] (OK) to return the function of Q-Surveying.If [F3] you want to cancel the settings, press [ESC] to ignore the changes.
Total Station Manual Steps 1 ƻ Key Display After entering to the interface of EDM Setting,using the direction of Ę Ę to move the cursor to the setting item of P.C. 2 Enter ƻ the prism constant value and press the key of [ENT]. Ć1Ć2Ć3 3 ƻ [ENT] After finished setting, press [F3](OK) to return the function of Q-Surveying.If [F3] you want to cancel the settings, press [ESC] to ignore the changes. Ć1: Prism constant you enter is effective only when the reflector mode isPrism.
Total Station Manual Steps 1 ƻ Key Display After entering to the interface of EDM Setting, [F1] press [F1] (Atoms) to enter the interface of Atomspheric Data. 2 ƻ Interface current setting, direction of Ę displays the using the to move the Ę cursor to the setting item of Refraction. + Press ĕė to select the value ĕė of refraction.Each time you press ĕ or ė , the value of refraction is switched. 3 After finished setting, press ƻ [F4] (OK) to save settins and back to previous menu.
Total Station Manual If the air pressure unit is mmHg, Make a conversion according to the formula: 1hPa=0.75mm Hg ¾ Standard meteorological conditions (atmospheric correction value =0 ): press: 1013hPa temperature: 20ć ¾ If the atmospheric correction is not required, please set PPM to zero. Steps 1 ƻ Key Display After entering to the interface of EDM Setting. [F1] Press [F1] (Atoms) to enter the interface of Atomspheric Data. 2 ƻ Interface displays the Ę current settings.
Total Station Manual item of PPM.Ć Ć Ć Ć 5 ƻ After finishing setting, press [F4](OK) to save settins and back to previous [F4] menu.Then press the key of [F3] [F3](OK) to save the setting of EDM and back to the function of measurement. Ć1: The range of enter: Temp.(-30ć̚60ć), Press.(500hPa̚1400hPa). Ć 2: The instrument calculates the value of PPM according to the values of temperature and pressure you enter. Ć3: Press [F1](PPM=0) can set the value of PPM to 0.
Total Station Manual HD: Ground distance 2. Ground distance HD=HDg/(Grid factor) Note: 1. The enter range of the scale factor: 0.99~1.01,the default value is 1.0. 2. The enter range of the average height above sea level: -9999.9999~9999.9999. The average altitude retained after the decimal point one, the default value is 0.
Total Station Manual 2.4 EDM signal The function of signal is to display the intensity of signal received by total station.If the target is hard to be found or can’t see, using the function can achieve the best sighting accuracy. Steps 1 ƻ Key Display After entering to the interface of EDM [F4] Setting,press the key of [F4] + to enter the second page of [F2] soft key, then press te key of [F2](Signal) to enter the function of Signal intensity.
Total Station Manual 3. Start measurement Q-Survey has 3 pages menu, including all measuring functions commonly used, such as angle measurement, distance measurement and coordinate measurement. As shown below: 3.1 Set HA You can set the horizontal angle as 0 or set it as wanted angle. Set horizontal angle to 0. Steps Key Display [F4] 1 Aim at the target which + ƻ [F4] used to orient.Press [F4] twice to enter third pages soft key.
Total Station Manual 2 ƻ Press [F2](Zero), the screen give a prompt to set HA as 0 or not. [F2] 3 Press [F4](Yes), the screen ƻ [F4] backs to Q-Survey and HA is or set as 0. If you want to cancel [F1] the operation,please press [F1](No). Set HA. Steps Key Display 1 ƻ Aim at the target which [F4] + used to orient.Press [F4] twice [F4] to enter third pages soft key. 2 Press [F3](SetHA) to enter ƻ [F3] the interface of SetHA.Screen displays the current value of HA.
Total Station Manual [ESC] to go back. B If want other value of angle as the orientation angle,you need to enter the wanted value of [F4] angle and press [ENT], then press [F4](OK). Example: enter 121.2030 (121e20Ą30ą). B: Input angle C: If want to set HA to 0,press [F1] [F1]( Zero) and the value + in the edit text of HA becomes [F4] 0 e 00 Ą 00 ą .Then press the key of [F4] (OK). 3 Back ƻ C: [Zero] to the function of Q-Survey, the value of HA [F4] just set displays in the [F1] interface.
Total Station Manual 3.2 Set Station and instrument height After set the coordinate of station (the site of instrument) relatives to the origin, the instrument can calculate the coordinate of the location to your position (the site of prism). You can set station and the instrument height conveniently in the Q-Survey. Steps Key Display [F4] + 1 Aim at the target which ƻ [F4] used to orient.Press [F4] twice + to enter third pages soft key.
Total Station Manual 3.3 Measurement After all settings have been finished, you can start to measure. There are 3 pages to display the result of measurement, including all measurement data and you can press [PAGE] to view. Steps 1 Input ƻ Key Display the name of point and instrument height.Move [ENT] the cursor to the next edit text + after entering each item. You [ENT] can enter Code when necessary.
Total Station Manual 3.4 Code The code contains the information about the recording points, in the process of post-processing, with the help of encoding function , you can process conveniently according to the specific group.The function of “File Manager” also contains the information of code. Simple Oeration of Code 1. Move the cursor to the line of Code. 2. Enter the name of Code. 3. Press the key of [ALL] to start the distance measurement and record the data of code and measurement at the same time.
Total Station Manual Before REC: Record code data before recording the actual measurement data. After REC: Record code data following after the actual measurement data.
Total Station Manual 4. Funtions Bring the total station’s common functions and settings together, they can be used in the process of measurement conveniently. In the function of Q-Survey which in the Main menu or other interface of measuremen in the program,you can press [FNC] to enter the menu of Function The menu of Function has 4 pages, you can press ǏPAGEǐ to view.
Total Station Manual station. ƹ Press [On] to open the compensator and press [Off] to close the compensator. ƹ Press [X Only] to open the compensator of X direction. ƹ Press [Ʒ][ͩ] to adjust the laser plummet brightness. ƹ Press [OK] to closs the laser plummet and exit. 2. Offset The Offset is used to measure the points which are not intervisible or intervisible but can not set up prism in the Station. Offset contains Dist.
Total Station Manual 1 ƻ In the program of Q-Survey, press [FNC] to [F2] open the menu of Function, next pressing [F2] to enter the program of Offset. 2 ƻ Input the values of Trav.OFS, LengthOFS and [F4] HeightOFS, then select the mode of offset and press [F4] to save.Ć Ć: Rec/Reset: Make sure the inputed values of Offset and reset all the values of Offset to 0 after once measurement. Permanent: The values of Offset are always working in the calculation of measurement point. 2.
Total Station Manual between cylinder and station. Steps 1 ƻ In the Key program of Q-Survey, press [FNC] to enter the menu of Function, then pressing [F2] to enter the program of Offset. 2 Press ƻ [F2] [F2] to enter the subprogram Offset. 3 Aim ƻ Display of Cylinder [F2] at the left edge of cylinder, press [F1] to make sure the angel of Hz Left, [F1]+[F2 turn the instrument to aim at ] the right edge of cylinder and press [F2] to make sure the angle of Hz Right.
Total Station Manual 5 ƻ Display the result of cylinder offset. 2.3 Angel Offset Angle Offset is used to measure the points which are intervisible but hava no reflector and can’t set up the prism. The basic principle is making the target point and measurement point in the concentric circles whose center is station point, then measuren the position information of station point and measurement point and the angle offset of station to target point, thus can calculate the coordinate of target point.
Total Station Manual 2 ƻ Press [F3] to enter the [F3] subprogram of Angel Offset. 3 Aim at ƻ the measurement point and press [F1] to measure distance. 4 Aim ƻ at the target point and press [F4] to make sure the direction of target point, next enter the program that displaying the result of angle measurement. 5 ƻ [F1] [F4] Display the result of angle Offset.
Total Station Manual 3. NP/P Toggle Switch the mode of reflector quickly. (P is the mode of Prism and NP is the mode of Non-Prism) Open the first page of Function Menu and press [F3] to switch the mode of reflector. 4. Height Transfer The functions of HT. Transfer as follows: Using the measurement data of target point, the fixpoints, fix measurement points and so on to calculate the height of current station point and set the height of station again.
Total Station Manual Steps Key Display 1 Press [F4] or [4] in the ƻ first page of [Function] to enter the function of Height Transfer measurement. 2 Press ƻ [F4] or [4] [F4] twice and [F4] display the third page of + soft keys, press [F2](IH)to [F4] enter the function of setting + instrument height, inputing [F2] the current instrument + height and press [F4] to [F4] back to the function of Height Transfer interface.
Total Station Manual 3 Selcet the fixpoint and ƻ input the height of Prism. The numbers of measured fixpoints are displayed in the top right corner. There are 3 methods to selecting fixpoint. A: Press [F4] to enter the second page of soft key and press [F2](List) .In the dialog of [Find Pt.], by pressing [▲] or [▼] to select the fixpoints to call. B: Input the name of point and press [F1] (View) to view the point whether exists in the file or not.
Total Station Manual 4 After ƻ finishing setting up the fixpoint, the height [F1] of fixpoint is displayed in or the screen and press [F2] [F1](ALL)or + [F2](DIST)+[F3](REC) to [F3] start to measure and calculate, the height of station is calculated. 5 ƻ In the interface of [Height Transfer Result], pressing [PAGE] to switch the display of result information. Press [F1](Add PT) to add [PAGE a new point and to start a ] new measurement. Press [F3](Back) to back to measure the current point again.
Total Station Manual 5. Hidden Point The function of Hidden Point is using a specia hidden point measuring rod to measure the points which are not intervisible. The length of measuring rod is known, by measuring the position information of prism 1 and prism 2 in the measuring rod and using mathematical methods to calculate the coordinate of hidden point on the other side of the measuring rod.
Total Station Manual 3 ƻ Inputting the correct value of Rod length and pressing [F4] to back to measure the first prism point. 4 The ƻ instrument aims at the prism on the top and pressing [F1] to finish measuring the first prism and enter the interface of measuring the second prism. [F4] [F1] or [F2] + [F3] 5 Aim at the second prism ƻ and press [F1] to finish the second prism’s measurement. Start to calculate the information of hidden point now.
Total Station Manual 7 ƻ Display the result of hidden point measurement. 6. Free Coding Please refer to Ā3. Q-SurveyāėĀ3. Start MeasurementāėĀ3.4 Codeā 7. Laser Pointer Open or close the laser fastly. 8. Light Turn on or off the light of instrument screen fastly. Open the second page of Function Menu and press [F4] to turn on or off the Light. 9. Unit Setting Set the common Unit fastly.
Total Station Manual Open the third page of Function Menu and press [F1] to enter the interface of unit setting. After finishing setting the units in the interface of Unit Setting, press [F4](OK) to save the settings,press [F1](Reset)to restore all units to factory default. 10. Main Setting Open the settings about instrument’s hardware, the specific items as follows: As for the setting of specific items , please refer to “General Setting”.
Total Station Manual 11. EDM Tracking Open or close the mode of EDM Tracking fastly. Open the thied page of Function Menu, press [F3] to open or close the mode of EDM tracking.
Total Station Manual 5. Applications Prepare setting before measuring: Before startingthe application, there are some preparations needed to set up. The Pre-Settingsscreenwill beshown after the user selects an application. User can select and set the content of the Pre-Settings menu successively. [*]: Setting has been done. [ ]: Setting has not been done. The details of every setting are as follows. 1.
Total Station Manual 2 Press [F2](New) and then ƻ enter the Create a New Job screen. Press [F4](OK), the displayed [F1] job will be set as current job and then back to Pre-Settings screen. 3 If the instrument ƻ is fitted with SDCard, there willfirstly showthe diskselection screen. In this screen, user can select the disk through Up or Down key. Then press [F4](OK) to confirm. A: Local Disk B: SD Card 4 Continue to show New Job ƻ screen. Input the new job’s name, operator, etc.
Total Station Manual Ć : The instrumentsystem will create and add date and time automatically. 1.2 Select anExisting Job from Memory If there is any job existing in the memory, user can select this job and set it as the current job. Steps 1 ƻ Press [F1] Key in the Pre-Settings screen. Then enter the Set Job function. 2 Press ƻ Display [F1] (List) to enter [F1] [F1] Job list screen. 3 ƻ All the existing jobs, including that stored on SD Card and will be shown as a list.
Total Station Manual job. 5 ƻ Back to Pre-Setting screen.The completed setting item is marked with *. [F4] 1RWH Don’t pull out the SDCard when it is in operating state, otherwise it will cause the SDCard’sdata loss or damage. ¾ All measureddatas are stored in the current job. ¾ If start the application without setting the job, press ALL key or press REC key in the Q-Surveying screen, the instrument system will create a job which named DEFAULT automatically. 2.
Total Station Manual 2.1 Select the coordinate from memory [Find] Steps: 1ǃ Select the coordinate from memory. 2ǃ Input instrument height. 3ǃ [OK] Set station. Steps 1 ƻ Press [F2] Key in Display the Pre-Settings screen. Then enter the Set STA function. [F2] Input 2 Input the name of the station point ƻ name point which exists in the job and + then press [ENT].
Total Station Manual the point is found, press [OK] in the [Find Pt.] list screen to set it as station. Program enter input instrument height screen. If the point doesn’t exist, press [F3](Coord.) to input the coordinates of N, E and Z. Set Back OK this point as station. [Zero]: Set this point’s all coordinates as 0 and set the point as station. [Coord.]: Enter [Input Coord.] screen. Input the coordinates and save them to the current job. 4 ƻ Enter input instrument height screen.
Total Station Manual 2 Press ƻ [F2](List) in the [F2] [Set STA] screen. 3 Show ƻ the point list all the fix points and measured points of the current job. [View]: 4 Select ƻ the needed point through Up and Down key. [View]: Show the Ė informations of this point. [Coord.]: Input the Ę coordinate datas manually. [Job]: Select datas from another job. [Coord.
Total Station Manual 5 After ƻ selecting needed point, press [F4](OK) and enter input instrument height screen. Complete all settings and then back to Pre-Settings screen. [F4] input instrument height + [ENT] [F4] 2.3 Input the coordinates manually. Steps: 1. Press [Coord.], enter input coordinate screen. 2. Input the point name and coordinates. 3. [OK] Save the station coordinates. And then input the instrument height. Steps 2 Press [F3](Coord.) in the ƻ Key Display [F3] [Set STA] screen.
Total Station Manual 4 Press ƻ [F4](OK) to save [F4] the coordinates of this point. 5 ƻ Program prompts"Saved!" Then enter input instrument height screen. Input the instrument height and press [ENT] to confirm. Then press [F4](OK) to finish the setting. 6 ƻ Input instrument height + [ENT] [F4] Back to Pre-Settings screen. The setting items that have been made are marked with *. 3.
Total Station Manual Steps 1 ƻ Press [F3] Key in Display the Pre-Settings screen. Then enter the Set STA function. [F3] 2 Press [F1] and select the ƻ [Angle Setting] to orientation manually. input 3 Aim B.S. point and then ƻ [F1] Input horizontal input the azimuth, prism angle height and backsight point + name. Press [ENT] after [ENT] finishing every input. 4 Press ƻ measuring [F1](ALL) to start and set the orientation.
Total Station Manual 5 ƻ Back to Pre-Settings screen. The setting items that have been made are marked with *. 3.2 Set orientation with coordinates The determination of the direction value can also be carried out using a point with a known coordinate. Steps: 1. Press [F2] to go to set orientation with coordinates 2. Input the name of orientation point and find the point. 3. Input the prism height and determine it. 4. Use this point to set orientation.
Total Station Manual 3 Aim ƻ backsight point and then press [ENT]. Press [F1](ALL) or press [F2](DIST) and [F3](REC) to start measuring and finish setting orientation. User can also press [F3](REC) to finish [ENT] setting orientation without measurement. [F1] or [F2] ǃ [F3] Press the [PAGE] key to switch the display of measured values screen and backsight inspection values screen. [EDM]: Go to set EDM settings. 4 ƻ Back to Pre-Settings screen. The setting items that have been made are marked with *.
Total Station Manual z z Stakeout Free Station z z z z z Tie Distance Area Remote Height COGO Road Steps: 1. Go to the MAIN MENU. 2. Move the focus to [Program] or press the Numeric key 2 to select and go to the PROGRAM MENU. 3. Press [PAGE] to browse the application menu. Press [F1]-[F4] to select and start an application. 5. Surveying Compared with the Q-Suveying, Surveying has different guides in setting station and set orientation.
Total Station Manual 1 After finishing setting the ƻ job, setting the station and [F4] setting the orientation, press [F4] to start the application in the Pre-Setting menu. Input point then press [ENT] to move to name next input item to input prism + height. [ENT] 2 Input the point name, and ƻ Input prism then press [ENT] to move the height cursor to next input item. If + needed, input the code.
Total Station Manual point. At this time, the screen remains the last measured data which can be looked over by pressing [PAGE].
Total Station Manual 5.1 Individual Point [IndivPt]: In the data acquisition, point can be recorded individually. Press this key to switch the screens of Individual Point Measurement and Consecutive Point Measurement. Steps 1 Press ƻ Key Display [F4]( Ę ) twice to display the last page of soft keys. [F4] 2 Press [F2](IndivPt) to start ƻ measuring function. individual point 3 Input the individual point’s ƻ name and prism height and press [ENT] to move the cursor to next input item..
Total Station Manual 4 Press ƻ [F1](ALL) or press [F1] or [F2](DIST) and [F3](REC) to [F2]+[F3 start measuring and record the ] measured data. 5 ƻ Finish measuring, application turn off the function of measuring individual point and then continue to display the consecutive point name. 5.2 Data [Data]: Look over the measured datas which are saved in current job. Steps 1 Press ƻ Display [F4]( Ę ) twice to display the last page of soft keys.
Total Station Manual 3 After ƻ inputting the target Input point’s name or wildcard (*), point press [ENT] and then press name/ [F4](View) to look over the wildcard datas. If there is no match + point, the program [ENT] prompts“Pt. not found!” + [Job]: Select the job where the [F4] measureddatais to be viewed. 4 ƻ Go to View Measured Point screen. Press [PAGE] to turn the page and look over all data field of this point. Press direction key ĕ and ė to browse the last measured point.
Total Station Manual 6. Stakeout The Stakeout Application can calculate lofting elementsbase on lofting point’s coordinate or manually input angle or horizontal distance. The application can continuously display differences, between current position and desired stake out position. Steps of Stakeout : 1. Set the job. 2. Set the station 3. Set the orientation 4. Extractecoordinates from memory. The coordinates may be a measured point or a manually entered fix point. 5. Start staking out.
Total Station Manual 3 ƻ A: The program searchs the point name in the job and show the result dialog. The match points will be listed, press [F4](OK) to identify selected point and back to Stakeout screen. (If the input is wildcard "*", the program will show all the points of the current job.)Ć2 B: If there is no match point in the job, the program prompts“Pt. not found!”.And then go in Find Point In Job screen. User can input a point or select a point from another job and then back to Stakeout screen.
Total Station Manual z Manual input stakeout point Press key [Coord.] or [SO-PT] to manual input stakeout point coordinates and then continue staking out. [Coord.]: Press [Coord.] and then input a target point’s coordinates. Saved this point into job and continue staking out. Steps Key Display 1 Press [F4] ( Ę ) to view ƻ the second page of soft keys. 2 Press [F2](Coord.) to go ƻ to Input Coord. Screen. Input point name and coordinate of the stakeout point.
Total Station Manual [SO-PT]: Press [SO-PT] to input a stakeout point without point name and being saved into job. Steps 1 Press [F4] ( Ę ) to view ƻ Key Display [F4] the third page of soft keys. 2 Press [F2](SO-PT) to go ƻ to SO-Input data screen. Input the coordinates of stakeout point. After input one item, the curser will move to next input item. 3 After ƻ [F2] + Input point name and coordinates + [ENT] finishing inputs, press [F4](OK) to save the data. And then back to Stakeout screen.
Total Station Manual 6.2 Polar Stakeout Mode The meanings of the differencesin thePolar Stakeout mode: ƸHz Difference in direction:If the measured point is located in the right side of stakeout point, the value is positive. Ƹ Difference in horizontal distance: If the measured point is farther than stakeout point, the value is positive. Ƹ Difference in height: If the measured point is higher than stakeout point, the value is positive.
Total Station Manual 2 Press ƻ [PAGE] to go to [PAGE] + Ę page 1/3(Default page). Press direction key and move the + cursor to input prism height Input item. Input the prism height prism and then press [ENT] to height + confirm. [ENT] 3 Aim ƻ at the prism. Press [F2](DIST) to start measuring [F2] and calculate the differences between measured point and stakeout point. 4 ƻ Turn the instrument telescope to make the Ƹ Hz equal 0 e 00 Ą 00 ą and command the staff to move the prism at the same time.
Total Station Manual move. 6 Move the prism according ƻ to the direction of the arrow to make the value of Ƹ equal 0m. Arrows Meaning: Ę : Move the prism close to the station. Ė : Move the prism far away the station. In the process of staking out, if using the Repeat Measurement or Tracking Measurement, the calculation of the differences between measured point and stakeout point can be displayedin real time and convenient.
Total Station Manual 8 Now itfinishes staking out ƻ a point.Repeat the previous steps to stake out next point. 6.3 Orthogonal to StationStakeout Mode Use longitudinal difference and perpendicular difference to indicatethe position differences of stakeout point and current prism position. The meanings of the differencesin theOrthogonal to StationStakeout Mode: ƸLength Difference in longitudinal distance: If the measured point is farther than stakeout point, the value is positive. ƸTrav.
Total Station Manual Ę 2 Press ƻ direction key and + move the cursor to input prism Input height item. Input the prism prism height and then press [ENT] to height confirm. + [ENT] 3 Aim ƻ at the prism. Press [F2](DIST) to start measuring and calculate the differences between measured point and [F2] stakeout point. The arrow’s direction is the direction of the prism need to move. 4 Move the prism according ƻ to the direction of the arrow to make the value of Length equal 0m.
Total Station Manual 5 ƻ Turn the instrument telescope to find the direction where makes the Ƹ Trav. equal 0m and command the staff to move the prism at the same time. Arrows Meaning: ĕ : Look forward from station and move the prism to the left. ė : Look forward from statio and move the prism to the right. 6 It means the current prism ƻ position is effective stakeout point while both the Ƹ Length and ƸTrav.are 0. Ƹ Z/H: Display as dig or fill data. Ę : The value expresses the depth of needed to dig.
Total Station Manual 6.4 Cartesian Stakeout Mode Stake out point based on the Cartesian coordinate system. The deviation values are the coordinate differences. The meanings of the differencesin theCartesian Stakeout Mode: ƸY/E The difference in East coordinate between measured point and stakeout point. ƸX/N The difference in North coordinate between measured point and stakeout point. Steps 1 ƻ Key Display Press [PAGE] to show Cartesian Stakeout Mode in page 3/3. Set the stakeout [PAGE] point.
Total Station Manual Ę 2 Press ƻ direction key and + move the cursor to input prism Input height item. Input the prism prism height and then press [ENT] to height confirm. + [ENT] 3 Aim ƻ at the prism. Press [F2](DIST) to start measuring [F2] and calculate the differences between measured point and stakeout point. 4 Move the prism along the ƻ East direction to make the value of ƸY/E equal 0m. Ƹ Y/E is positive: The stakeout point is in the right side of measured point. Move the prism to right.
Total Station Manual In the process of staking out, if using the Repeat Measurement or Tracking Measurement, the calculation of the differences between measured point and stakeout point can be displayedin real time and convenient. 6 It means the current prism ƻ position is effective stakeout point while both theƸY/E and ƸX/N are 0. Ƹ Z/H: Display as dig or fill data. Ƹ Z/H is positive: The value expresses the depth of needed to dig. Ƹ Z/H is negative: The value expresses the height of needed to fill.
Total Station Manual 6.5 [Polar] Press [Polar], then input the polar stakeout elements: Azimuth and Horizontal distance. Start to stake out after finishing inputs of Azimuth and Horizontal distance. Steps 1 Press ƻ Key Display [F4]( Ę ) twice to view the second page soft keys. 2 Press [F1](Polar) to show ƻ [F4] [F1] the dialog as shown in figure. 3 Input the stakeout point’s ƻ name, azimuth and horizontal distance. Press [ENT] to confirm every input and move the cursor to next input item.
Total Station Manual 4 Aim ƻ at the prism. Press [F2](DIST) to start measuring [F2] and calculate the differences between measured point and stakeout point. 5 ƻ Turn the instrument telescope to make the Ƹ Hz equal 0°00’00” and command the staff to move the prism at the same time. Ƹ Hz is positive: The stakeout point is in the left side of measured point. Move the prism to left. Ƹ Hz is negative: The stakeout point is in the right side of measured point. Move the prism to right.
Total Station Manual 7 Move the prism along the ƻ arrow direction to make the value of Ƹ equal 0m. In the process if using Measurement Measurement, of staking out, the Repeat or Tracking the calculation of the differences between measurement point and stakeout point can be displayedin real time and convenient. 8 Now itfinishes staking out ƻ a point.Repeat the previous 2 ̚ƻ 7 to stake out steps ƻ next point. Ć1: The inputs of polar coordinate data won’t be saved to job.
Total Station Manual 7. Resection Resection measurement is an application used to determine the coordinate of the instrument station by measuring multiple known points. A minimum of 2 and a maximum of 5 known points can be used to determine the station. It should be used at least 2 known points by distance measurement or at least 3 known points by angle measurement. Steps Key Display 1 Select “Program” from the ƻ [Main Menu] window, press [F3] [F3] or number key [3] to enter the Resection application.
Total Station Manual 4 The ƻ window back to the [Resection] window, and press [F2] to set error limits. [F2] 5 Press [◄] \ [►] to turn on ƻ the error limits status and use the key [▲] \ [▼] to move the focus down to input the every error limit. Then press [F4] (OK) to set and back to the [Resection] window. 6 Press ƻ [F4] in [Resection] window to start resection measurement. It should be input the station name and the instrument high. Then press [F4] (OK) go to next step.
Total Station Manual angle. Distance measurement: [F1] (ALL) or [F1] + [F2] (DIST + REC). 9 ƻ When finish a known point measurement, press [F2] (NEXT PT) to start next [F2] known point measurement. 7 and ƻ 8 . Repeat stepsƻ 10 If ƻ the measured known points are enough, [Result] will display on the screen, then press [F3] (Result) to enter the [Station Coordinate] to view station result. Press [F1] (Back) back to a new known point measurement.
Total Station Manual Ć 1: The known points can be called from the memory through the [Find], [List] or manually entered used [Coord.].
Total Station Manual 8. Tie Distance Tie Distance is an application used to compute slope distance, horizontal distance, height difference and azimuth of two target points which are either measured, selected from the memory, or input using the keypad. The user can choose between two different methods: Ь Polygonal: P1-P2, P2-P3, P3-P4 Ь Radial: P1-P2, P1-P3, P1-P4 Start Tie Distance application through “Main Menu”ė”Program”ė”Tie Distance”. 8.
Total Station Manual 2 ƻ After finishing setting job, station and orientation, press [F4] in the Pre-Setting menu to go to Select Tie Distance Mode screen. 3 Press ƻ [F1] to select the [F4] [F1] Polygonal tie distance. 4 Start to measure the first ƻ target point. Aim at the first target point and press [F1](ALL) or [F2](DIST) + [F3](REC) to finishing measurement.
Total Station Manual 5 ƻ Start to measure the second target point. Aim at the second target point and press [F1](ALL) or [F2](DIST) + [F3](REC) to finishing measurement. Ć1 6 ƻ Show the result PAGE1 Press [F1] or [F2] + [F3] of polygonal tie distance. [NewPt1]: Start a new polygonal tie distance. [NewPt2]: This polygonal tie distance’s second point will be the new polygonal tie distance’s first point and then go to ƻ 5 to measure the new second target point.
Total Station Manual 8.2 Radial While Radial tie distance measuring continuous points, the new tie distance’s first point continues usingthethe previous tie distance’s first point(P1-P2 ǃ P1-P3 ǃ P1-P4ĂĂ). Steps Key Display 1 Press [F4] in the Program ƻ Menu to go to Tie Distance application. 2 ƻ [F4] After finishing setting job, station and orientation, press [F4] in the Pre-Setting menu to go to Select Tie Distance Mode screen.
Total Station Manual 3 Press ƻ [F2] to select the [F2] Polygonal tie distance. 4 Start to measure the first ƻ target point. Aim at the first target point and press [F1](ALL) or [F2](DIST) + [F3](REC) to finishing 1 measurement. Ć 5 Start to measure the first ƻ target point. Aim at the first target point and press [F1](ALL) or [F2](DIST) + [F3](REC) to finishing measurement.
Total Station Manual 6 Show the result of Radial ƻ tie distance. [NewPt1]: Start a new Radial tie distance. [NewPt2]: This Radial tie distance’s first point continues to be the new polygonal tie distance’s first 5 to point and then go to ƻ measure the new second target point. [Polygonal]Radial: Go to Polygonal tie distance. Ć1: The target points can be measured, selected from the memory, or input using the keypad.
Total Station Manual 9. Area Area is an application used to calculate the polygon areas to a maximum of 20 points which connected by straights. The target points coordinate can be measured, selected from memory or entered via keypad in same direction. And the following three methods can be alternately performed. The calculate area is projected onto the horizontal plane (2D). Figure 9.
Total Station Manual 2 After finishing the ƻ pre-settings more details beginning of 5), press [F4] Area app. 3 ƻ (know [F4] at the or chapter [4] to start There are four ways to get target point for Area A: Get the target point by measure. calculation. Input point name and A: Input the name of prism target point in“Pt.” height field and input prism + height in “T.H.
Total Station Manual is in memory, if exist, [F4](OK) then press [F4](OK) to be selected for calculating; if not exist, then need to input or measure the point. [F2](Coord. ) D: Press [F2] + (Coord.) to input a Input point that not exist in Coord. memory. + [F4](OK) 4 ƻ D: Input the point through keyboard. Set other target point as described above four ways. The area result will be calculated and showed at “Area” field automatically when there are more than 3 target points be set in application.
Total Station Manual 6 If the target points ƻ are set, then can press [F3](Result [F3] (Result) to show ) the [Area Result] window to view the result. Ć In [Area Result] window: Press [F1] (New Area) to restart a new Area application. Press [F2] (Graph) to show the area graph projected onto the horizontal plane. Press [F4] (Add PT) to return the current Area application and continue operation. Press [ESC] to exit the Area application.
Total Station Manual Steps 1 ƻ Key Display Select “Program” from [PAGE] the [Main Menu] window, + then press [PAGE] switch to [F2] second program list and or press [F2] or number key [6] [6] to enter the Area application. 2 ƻ After finishing the pre-settings (know more details at the beginning of [F4] chapter 5), press [F4] to enter the [Base Pt.] window to start Remote Height app.
Total Station Manual 10.
Total Station Manual 4 Move the prism just ƻ standing below the remote point, then aim at the bottom of prism rod and press [F1] (ALL) or [F2] + [F3] (DIST + REC) to finish the base point measuring. 5 ƻ Turn the Turn the ] instrument telescope aimed at prism and press [F4] to measure the prism high. Then enter the [REM PT] window. 6 ƻ [F1] or [F2]+[F3 [F4] instrument telescope aimed at remote point and press [F4] to finish current remote point measuring. Press [F1] to re-set the base point.
Total Station Manual Figure 11.1 Traverse Diagram Known P0 a d d1 d2 Unknown P1 P2 P3 known point Direction from P1 to P2 Distance between P1 and P2 Positive offset to the right Negative offset to the left COGO point without offset COGO point with negative offset COGO point with positive offset Steps 1 Select ƻ Key Display “Program” from the [Main [PAGE] Menu] window, then + press [PAGE] switch [F2] to second program list or and press [F1] or [7] number key [7] to enter the COGO application.
Total Station Manual 2 After finishing the ƻ pre-settings more details beginning of 5), press [F4] COGO app. (know [F4] at the or chapter [4] to start [F1] 3 In [COGO Menu] or ƻ [1] screen, press the [F1] or number key [1] enter the [Traverse & Inverse] screen, press [F2] or [2] enter the [F2] traverse or subapplication. [2] 4 ƻ There are four A: Get the known point by COGO-Meas. ways to get the Input point known point for name traverse calculation. + [F1](Meas.
Total Station Manual the “T.H.” field in [COGO-Meas], then COGO-Meas. aim the prism and press [F1] (ALL) or [F2] (DIST) + [F3] (REC) to measuring and saving the point for calculation. traverse B: Press [F1](List) in [Traverse] screen, use the key [▲]\[▼] to [F1](List) select a Known point + in the point list for [F4](OK) traverse calculation, then press [F4](OK) to be selected.
