User's Manual

ManualsBrandsGentex ManualsElectronicsUniversal Garage Door Opener Transmitter

Table Of Contents

Programming and Information Guide Programming and Information Guide

The HomeLink Wireless Control System provides a convenient way to replace up to three

hand-held radio-frequency (RF) transmitters used to activate devices such as gate

operators, garage door openers, entry door locks, security systems, even home lighting.

Additional HomeLink information can be found on the Internet at www.homelink.com

The HomeLink Wireless Control System provides a convenient way to replace up to three

hand-held radio-frequency (RF) transmitters used to activate devices such as gate

operators, garage door openers, entry door locks, security systems, even home lighting.

Additional HomeLink information can be found on the Internet at www.homelink.com

by calling 1-800-355-3515.

Precautions

Before programming HomeLink to a garage door opener or gate operator, make sure

that people and objects are out of the way of the device to prevent potential harm or

damage. When programming a garage door opener, it is advised to park outside of the

garage. Do not use HomeLink with any garage door opener that lacks safety stop and

reverse features as required by U.S. federal safety standards (this includes any garage

door opener model manufactured before April 1, 1982). A garage door that cannot detect

an object - signaling the door to stop and reverse - does not meet current U.S. federal

safety standards. For more information, contact HomeLink at: www.homelink.com or

by calling: 1–800–355–3515.

Retain the original transmitter of the RF device you are programming for use in other

vehicles as well as for future HomeLink programming. It is also suggested that upon

the sale of the vehicle, the programmed HomeLink buttons be erased for security

purposes. Refer to “Programming” (step #1 only) or, for assistance, contact HomeLink

at: www.homelink.com

or by calling: 1-800-355-3515.

Programming HomeLink

Note: Some vehicles may require the ignition switch to be turned to the second (or

“accessories”) position for programming and/or operation of HomeLink. It is also

recommended that a new battery be placed in the hand-held transmitter of the device

being programmed to HomeLink for quicker training and accurate transmission of the

radio-frequency signal. Do not repeat “Programming” - step one to train additional

devices to a second or third HomeLink button. Begin with “Programming” – step two.

1. Press and hold the two outer HomeLink buttons (buttons one and three) - releasing

only when the indicator light begins to flash (afte

r 10 seconds). Do not hold the

buttons for longer than 30 seconds

and do not repeat step one to program a

second and/or third hand-held transmitter to the remaining two HomeLink buttons.

2. Position the end of your hand-held transmitter 1–3 inches (5–14 cm) away from the

HomeLink button you wish to program while keeping the indicator light in view.

3. Simultaneously press and hold both the chosen HomeLink and hand-held transmitter

buttons. Do not release the buttons until step 4 has been completed.

(Note: Some gate operators and garage door openers may require you to replace

this Programming Step 3 with procedures noted in the “Gate Operator / Canadian

Programming” section.)

Summary of content (4 pages)

PAGE 1
Programming and Information Guide The HomeLink Wireless Control System provides a convenient way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, even home lighting. Additional HomeLink information can be found on the Internet at www.homelink.com or by calling 1-800-355-3515.
PAGE 2
Programming (cont’d.) 4. After the HomeLink indicator light changes from a slow to a rapidly blinking light, release both the HomeLink and hand-held transmitter buttons. Note: If the HomeLink indicator light does not change to a rapidly blinking light, contact HomeLink at www.homelink.com or call 1-800-355-3515 for assistance. 5. Press and hold the just-trained HomeLink button and observe the indicator light.
PAGE 3
Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
PAGE 4
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.