User's Manual

ManualsBrandsGentex ManualsElectronicsUniversal Garage Door Opener in Mirror

EXHIBIT D: O

WNER

’

ANUAL

[2.1033(

3)]

Recommended Owners Manual for Automatic-Dimming NVS Mirror with Homelink® series

Universal Garage Door Opener, Electronic Compass and Outside Temperature Display.

Automatic-Dimming NVS



 Mirror with Homelink®, Electronic Compass and

Outside Temperature Display

Suggested Owner’s Manual Text

December 2001

Automatic-Dimming Night Vision Safety







(NVS







) Mirror

The

NVS Mirror in your vehicle is the most advanced way to eliminate dangerous and

annoying glare in the rearview mirror during any driving situation. For more information

regarding NVS mirrors and other applications, please refer to the Gentex website –

www.gentex.com.

Precautions

The NVS Mirror automatically reduces glare during driving conditions based upon light levels

monitored in front of the vehicle and from the rear of the vehicle. These light sensors are visible

through openings in the front and rear of the mirror case. Any object that would obstruct either

light sensor will degrade the automatic dimming control feature.

Operation

The NVS Mirror operates automatically whenever the vehicle ignition is ON. The status of the

automatic dimming feature is indicated by a green light on the face of the mirror.

To turn the automatic dimming feature off, press the button with the

button. The indicator

light will turn off to indicate that the automatic dimming feature is off.

To turn the automatic dimming feature on, press the button with the

button again. The

indicator light will also turn on.

If the automatic dimming feature is off when the vehicle ignition is turned off, the automatic

dimming feature will become active when the vehicle ignition is turned back on.

Summary of content (7 pages)

PAGE 1
EXHIBIT D: OWNER’S M ANUAL [2.1033(A3)] Recommended Owners Manual for Automatic-Dimming NVS Mirror with Homelink® series Universal Garage Door Opener, Electronic Compass and Outside Temperature Display.
PAGE 2
Electronic Compass and Outside Temperature Display The NVS Mirror in your vehicle is also equipped with a display the shows the vehicle heading using the 8 basic cardinal headings (N, NE, E, SE, etc.). The NVS Mirror may also include a display of the outside temperature. For more information regarding these features in the NVS mirrors, please refer to the Gentex website – www.gentex.com. Electronic Compass Mirror Operation The Compass display operates automatically whenever the vehicle ignition is ON.
PAGE 3
To adjust the zone setting press and hold the button with the symbol for more than 3 seconds. Determine the appropriate zone number based upon your current location and the map provided above. Press and hold the button until the new zone setting appears on the display (note: the numbers will repeat, …13, 14, 15, 1, 2, …). Release the button and within about 5 seconds the compass will start displaying a compass direction again. There are some conditions that can cause changes to the vehicle magnets.
PAGE 4
To adjust the zone setting press and hold the button with the symbol for more than 6 seconds. Determine the appropriate zone number based upon your current location and the map provided above. Press and hold the button until the new zone setting appears on the display (note: the numbers will repeat, …13, 14, 15, 1, 2, …). Release the button and within about 5 seconds the compass will start displaying a compass direction again. There are some conditions that can cause changes to the vehicle magnets.
PAGE 5
Programming Note: For best results, replace the battery in the hand-held transmitter with a new battery before programming. If your garage door opener receiver (located in the garage) is equipped with an antenna, make sure the antenna is completely uncoiled and hangs straight down. 1. Press and hold the two outside buttons - releasing only when the indicator light begins to flash after 20 seconds.
PAGE 6
Canadian Programming / Gate Programming Canadian frequency laws, and the technology of some entry gates, require you to “cycle” (press and re-press the handheld transmitter button every two seconds) during programming. Continue to press and hold the desired HomeLink button (note steps 3 through 5 in the “Programming” portion of this text) while you “cycle” your hand-held transmitter until the frequency signal has been learned. The indicator light will flash slowly and then rapidly upon successful training.
PAGE 7
3. Firmly press and release the programmed HomeLink button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require you to do this procedure a third time to complete the training.) The garage door opener should now recognize the HomeLink signal and activate when the HomeLink button is pressed. The remaining two buttons may now be programmed if this has not previously been done. Refer to the “Programming” portion of this text.