MULTI-FUNCTION DIGITAL WIRELESS HEADSET USER'S MANUAL Models Z-280, Z-350, Z-470
Contents Introduction . . . . . . . . . . . . . . . . 4 Contents of this Package . . . . . . . . . . 5 Cautionary Notes . . . . . . . . . . . . . 8 Positioning of the Headset . . . . . . . . . 10 Changing the Ear Tip . . . . . . . . . . . . 12 Charging the Headset . . . . . . . . 12 Turning On/Off the Headset . . . . . . . . 13 Digital Volume Control. . . . . . . . . . . 14 Pairing the Headset . . . . . . . . . . . . 15 Multiple Pairings . . . . . . . . . . . . . .
TM L-E-A-P Feature (Model Z-470) . . . . . Hi-Fi Music Audio Input (Models Z-350 and Z-470) . . . . . . . Graphic Equalizer . . . . . . . . . . . . Minimizing Power Consumption . . . . . Troubleshooting . . . . . . . . . . . . . Limited Warranty . . . . . . . . . . . . Safety Warnings . . . . . . . . . . . . . TM ® Trademarks and Registered Trademarks FCC Notice . . . . . . . . . . . . . . EU Notice . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . Gennum Contact Information . . . .
Introduction TM ® The Z-E-N Models Z-280, Z-350 and Z-470 headsets use Bluetooth wireless technology to connect to phones or other devices, which support the headset or handsfree profiles. While connected to your phone (Phone Mode),you can make and receive calls using the headset,including using voice control features if your phone supports this function. All models allow the user to customize the receive phone audio using a 5-band Graphic Equalizer.
Contents of this Package 1 1 1 1 1 1 1 TM Z-E-N DigitalWireless Headset Mini Bag of ReplacementTips Installation CD User's Manual Fitting Guide Audio Interface Cable ACWall Charger © 2005 Gennum Corporation All rights reserved Page 5
EAR HOOK PINCH BUTTON SIDE BUTTON EAR TIP Page 6 BLUE INDICATOR LIGHT © 2005 Gennum Corporation All rights reserved
FLEXIBLE ARM ROTATE ARM FOR RIGHT EAR FIT DIGITAL VOLUME CONTROL CHARGING PORT / AUDIO INPUT PORT © 2005 Gennum Corporation All rights reserved Page 7
Storage Position Rotate the flexible arm upwards into the upright position as shown in the photograph for storage.
NOTE: Only rotate the flexible arm above the body of the headset NOTE: Only stretch the flexible arm out sufficient to position on the ear © 2005 Gennum Corporation All rights reserved NOTE: Do not attempt to forcibly rotate the flexible arm below the body of the headset or irreparable damage will occur NOTE: Do not stretch the flexible arm out to the position shown or continuously manipulate the arm outwards and inwards or irreparable damage will occur Page 9
Positioning the Headset It is recommended you stand in front of a mirror when trying to fit the headset for the first time. You can fit the headset on either the left ear or right ear by first rotating the flexible arm over the top of the headset onto the left side or right side respectively. Grasp the headset between your thumb and index and middle fingers as shown. Position the body of the headset over the top of the ear and insert the ear tip into the ear.
NOTE: the arm is made from a flexible rubber material throughout its entire length and is meant to be adjustable. Please position the arm in the shape desired, to get the most comfortable fit for you. PositioningTip To obtain the best possible results with your headset,it is important to ensure that the ear tip is inserted snugly into the ear. A snug fit will provide the best possible sound quality as well as good isolation from external background noise allowing you to hear the incoming call more clearly.
Changing the EarTip With one hand, firmly grasp the end of the ear tip between your thumb and index finger. Similarly, with the other hand, grasp the end of the flexible arm. Remove the ear tip with a gentle tug. To replace the ear tip,reverse this procedure by aligning the hole in the ear tip and pushing it on the end of the flexible arm until it is firmly seated in position.
headset Plug the AC power adapter into an electrical wall outlet If charging is required, the Blue Indicator Light will turn on indicating charging is in progress (if the Blue Indicator Light does not turn on, the headset is already fully charged) The Blue Indicator Light will flash when charging is complete If left plugged-in, the Blue Indicator Light will eventually stop flashing (Charging is automatically stopped in order to protect your headset) Turning On/Off the Headset To turn ON the headset
To turn OFF the headset, press and hold the SIDE button until you hear 4 beeps. Release the SIDE button and you will hear a quick series of tones going from high to low pitch. If you are not wearing the headset, press and hold the SIDE button for 4 flashes of the Blue Indicator Light.
L-E-A-PTM 2 or Phone) is entirely independent so changing the volume in one mode,will not affect the other modes. NOTE: Do not initially turn the volume control to maximum until you become familiar with the volume levels and determine what is most comfortable for you Pairing the Headset You must successfully complete the following pairing procedure to allow the headset and your phone to communicate.
? Follow your phone's pairing procedure to pair it with the headset ? When found,the headset will display as“Z-E-N” on your phone. ? When asked for the passkey, password or pin code, enter on the phone's keypad:0000 ? If pairing is successful, your phone will display a “pairing successful” message and the Blue Indicator Light will turn off. If you are wearing the headset,you will hear a 'pairing success' melody ? Depending on your phone model, you may have to initiate a Bluetooth Connection.
move the headset from one device to the next,use the following procedure: ? Turn off the headset ? Turn off the phone or device to which it is currently connected or, turn off the Bluetooth function,or select“Disconnect Z-E-N” manually from your phone's menu options ? Turn on the new phone or device you want to now connect with the headset.
FEATURES FOR PHONES SUPPORTING THE BLUETOOTH® HEADSET PROFILE ONLY If your phone only supports the Bluetooth Headset Profile,then the following features are available. Answering a Call If your headset is linked to your phone, then with an incoming call, you will hear a series of ring tones in the earpiece of the headset ? To answer the call, briefly press and release the SIDE button. Ending a Call ? To end the call, briefly press and release the SIDE button.
the call from your phone to the headset, press and hold the PINCH button until you hear 1 beep,then immediately release the button Mute/ Unmute While on an active call, ? To MUTE the call, briefly press and release the PINCH button. You will hear 1 beep followed by periodic beeps, indicating the headset has been muted ? To UNMUTE the call, briefly press and release the PINCH button.
? To answer the call, briefly press and release the SIDE button. If your headset is not linked to your phone, you will not hear the ring tones in your headset,however you can still transfer the incoming call to your headset at any time by by pressing and holding the PINCH button for 1 beep. It may take a few seconds longer to transfer. Ending a Call ? To end the call, briefly press and release the SIDE button.
Voice Dial If your phone supports voice-activated dialing and you have set up voice tags on your phone, ? Press and hold the PINCH button until you hear 1 beep, then immediately release the button NOTE: You should create the voice tags from your headset for better results Last Number Redial ? Press and hold the PINCH button until you hear 2 beeps, then immediately release the button Last Number ReDial while on a Call ? Press and hold the PINCH button until you hear 2 beeps, then immediately release the bu
immediately release the button.
first call on-hold ? Press and hold the PINCH button until you hear 1 beep, then immediately release the button to swap between an active and a held call ? Press and hold the PINCH button until you hear 2 beeps, then immediately release the button, to accept the waiting call and hang-up the original call ? Press and hold the PINCH button until you hear 3 beeps, then immediately release the button,to reject the waiting call ? Press and hold the PINCH button until you hear 4 beeps, then immediately release th
Call State ? When you are on a call, the Blue Indicator Light will flash periodically. It will stop flashing when the call ends Low Battery State ? When the headset requires re-charging, you will hear a warning tone from your headset. You will receive warnings every minute when 15 minutes of battery time are left. Warnings will increase to every 10 seconds when battery time is 5 minutes or less. When the battery expires,the unit will power itself off.
TM L-E-A-P Feature (Model Z-470 only) This feature is available while you are not on a call. When you use the L-E-ATM P (Local Environment Audio Processing) feature, you will more clearly hear the person you are in face-to-face conversation with, because the headset uses its advanced noise reduction algorithm to minimize the amount of TM background noise you hear. Two L-E-A-P modes are available,namely L-E-ATM TM TM P 1 and L-E-A-P 2.
TM NOTE: The volume control in each mode (Hi-Fi Music, L-E-A-P 1, L-E-ATM P 2 or Phone) is entirely independent so changing the volume in one mode, will not affect the other modes. When in either of these modes,the user may also customize the audio. Refer to the section on the Graphic Equalizer.
Refer to the section on the Graphic Equalizer which allows the user to customize the audio. Model Z-470 Only If the user is listening to Hi-Fi Music between calls and needs to conduct a TM face-to-face conversation using the L-E-A-P feature, a quick press and TM release of the SIDE button will put the headset into the last selected L-E-A-P memory. A subsequent quick SIDE button press will continue playing Hi-Fi music through your headset.
? Open and read the README.
or Passkey, enter: 00000000 ? Select 'Connect SPP Slave' ? After the pairing procedure is completed, make note of the COM port value as shown NOTE: The windows shown above are for the Windows 2000 operating system and may appear different for other operating systems such as Windows XP, however the basic procedure remains the same. NOTE: When the headset has been paired to the PC, you do not have to repeat the pairing procedure unless you want to pair to another PC.
? Enter PIN code“00000000” when prompted Application Setup ? Select the drop down menu next to the 'Connect' button COM Port Selection ? Click on ‘Set COM Port' and enter the COM port value noted above ? Click 'Update' to save the COM port value Page 30 © 2005 Gennum Corporation All rights reserved
? Click 'Connect' to establish a connection to the headset and the current equalization settings will be displayed TM TM ? Click on the appropriate tab (Hi-Fi Music, L-E-A-P 1, L-E-A-P 2 or Phone) to select the mode you want to program Programming the Headset There are three ways to customize the equalization settings in the headset: ? Dragging the sliders which programs the setting into the device as each slider is moved ? Using one of the pre-defined presets which contain default equalizations settings f
? Click on your selection and the equalization settings will be programmed into the headset.
? Click on your selection and the equalization settings will be programmed into the headset ? Individual sliders can be changed to further tune the settings to your liking TM L-E-A-P Mode Presets Phone Mode Programming and Presets Phone Mode Programming To listen to changes that you have programmed in Phone mode: © 2005 Gennum Corporation All rights reserved Page 33
TM headset and to the PC audio port Ensure the volume level on the PC is not muted Click the 'Play Test Call' button and you will hear the test call audio.
NOTE: A Microphone Gain slider is also available which controls the loudness level of your voice heard by the person you are talking with on the phone. Adjust this setting only if your called party complains that your voice is not loud enough.
? Drag the sliders into the positions you prefer ? Click the 'Save' button and save the file with a .zen extension. You may save as many files as you like. ? To load a previously saved file, click the 'Load' button and browse for the file you want to load TM Disconnecting the Z-E-N There are two ways to disconnect from the headset: ? Clicking 'Disconnect' will disable the connection to the headset.
TROUBLESHOOTING The phone or headset does not respond at all when I press the SIDE or PINCH buttons? You may need to reset your phone by turning off the power and then turning it TM back on again. You may also need to turn the Z-E-N headset off and then back on. All button presses on the headset are accompanied by a flash of the Blue Indicator Light. If you don't see a flash, this is a definite indication of a dead battery.
Limited Warranty Gennum Corporation warrants that your headset will be free from defects in material or workmanship for a period of one (1) year from the date of shipment, under normal use and conditions. For all warranty and service related matters, please see the Gennum Contact Information on the last page of this manual. During this period, if the headset is found to be defective in materials or workmanship,Gennum will repair or replace it,at the sole option of Gennum, at no charge to you.
Warranty repairs are completed at no charge for parts or labour, and Gennum will pay the cost of shipping the repaired or replaced product back to you.Warranty repairs may use new or equal replacement parts. Goods will not be accepted for return for non-warranty reasons without the express prior written approval of Gennum. Gennum reserves the right to make the final decision on any warranty claim that may be questionable.
IMPLIED CONDITIONS AND WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL GENNUM BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE HEADSET, THE USE OF THE HEADSET OR OTHERWISE, WHETHER FOR LOSS OF PROFITS, BUSINESS REVENUES OR OTHERWISE.
SafetyWarnings This package contains small parts which may be hazardous to children under 3. Headsets encourage hands-free operation of phones while driving or conducting other activities. You should nonetheless ensure you obey the laws regarding cell-phone use while driving, and give your full attention to the operation of your vehicle. Do not attempt to use this device if it is submerged in liquid. Immediately unplug all electrical connections.
and any use of such marks by Gennum Corporation is under license. TM The Z-E-N and L-E-A-P™ trademarks are owned by Gennum Corporation. FCC Notice This device contains FCC ID SD7GR2316 which complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation.
EU Notice DECLARATION OF CONFORMITY In accordance with Annex IV of the EU directive 1999/5/EC, Gennum Corporation declares under our responsibility that the product: Z-280,Z-350,Z-470 Type: Bluetooth Headset Intended Purpose: 1 Equipment Class: complies with the appropriate essential requirements of the Article 3 of the R&TTE and the other relevant provisions,when used for its intended purpose. Please refer to the zen.gennum.com website for more information.
Gennum Contact Information For latest revisions to this manual, customer assistance or inquiries about the TM Z-E-N headset,please visit our website at zen.gennum.com For general inquiries,please e-mail us at zen@gennum.com CorporateAddress: Gennum Corporation 970 Fraser Drive, Burlington, Ontario L7L 5P5 www.gennum.com ZEN350series 2.