User's Manual

ManualsBrandsGenie ManualsElectronicsRemote Control Transmitter for Garage Door Opener Operation

STEP 1:

This Wireless Keypad is compatible with all

and CODEDODGER® 2 radio equipped GENIE® products.

Drill with 1/16" Drill Bit

Phillips Screwdriver

Pencil

Mounting Screws INCLUDED

Ability to Control up to three

Overhead Door®CODEDODGER®1

or 2 Openers

Simple to Program and Install

PIN Codes can be up to 8 Characters

Low Battery Power Indicator

Stays Programmed During

Battery Change

Temporary PIN for Special

Purpose Access

OPERATING INSTRUCTIONS

(KEEP FOR FUTURE REFERENCE)

37257501192

STEP 3:

Following programming—

On your Wireless Keypad:

Enter your PIN.

OPERATING DOOR OPENERS

Proceed to Section 3 - Mounting Instructions.

MOUNTING INSTRUCTIONS

The Keypad must be mounted in sight of the Door(s), at

least 5 feet above the ground and clear of any moving

Door parts.

A Mount Keypad.(Mounting screws located inside

Battery Compartment.)

s Remove Battery Cover and batteries. (See Figure 3).

Drill a 1/16”pilot hole for the top mounting screw.

s Install a screw into the drilled

hole,leaving a 1/8" gap

between the screw head

and the wall. (See Figure 2.)

s Hook the Keypad over

the screw.

s Mark and drill pilot hole and

fasten bottom screw.

s nstall Batteries and Cover.

For answers to questions,call 1-800-275-6187 , or visit

www.overheaddoor.com

Overhead Door Corp., 2501 S State Hwy.,Suite 200, Lewisville, TX

75067. Additional products can be ordered through local

Overhead Door® Professional Dealers. To locate a dealer near you,

call 1-800-929-DOOR.

SECTION

ADDITIONAL OPERATIONS

SECTION

SING A

EMPORARY

A temporary PIN allows temporary access to your home by

If you have forgotten your PIN or you fear it may have fallen

into unauthorized hands, you must erase the old programming.

repair persons, meter readers, etc.if you so desire.

NOTE

DONOT reprogram the Door Opener(s).

Temporary PIN remains active only until the next time

nyour ormal PIN is entered.

ORGOT

OUR

PIN (RESETTING WIRELESS KEYPAD)

HANGING

OUR

Enter your current PIN and press .

Wall

screw head gap

Figure 2

FOR CONVENIENCE

Program Keypad BEFORE mounting.

MULTIPLE

EATURES

OOLS

EEDED





 

2YHUKHDG'RRU&RUSRUDWLRQ

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and

found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which may be determined by turning the equipment OFF and ON, the user is

encouraged to try to correct the interference by one or more of the following measures:

s Re-orient or relocate the receiver antenna.

s Increase the separation between the opener and receiver.

s Connect the opener into an outlet on a circuit different from that to which the receiver is connected.

s Consult your local dealer.

HANGING

ATTE RY

NOTE

If the Door does not move,check the LED on Keypad.

If the LED is blinking rapidly,the PIN was entered

incorrectly. After the LED stops blinking,re-enter

your PIN and try again.

Any Keypad Button will control the Door for 30 seconds

after the Door starts moving.

Rapid blinking of the red LED indicates an error. After a

few seconds the LED will turn off. Start over.

If your garage door opener has a Serial Number

sticker which looks like this, in which the

first two numbers are 10 or higher, your opener

is equipped with CODEDODGER®2.

Follow the instructions on this page.

Otherwise, follow the instructions on back.

s Press in order .

s Press .

s Enter your PIN (3 to 8 c

haracters).

s Close keypad cover and wait 30 seconds.

Press .

3 5 7

STEP 1:

REATING YOUR WIRELESS KEYPAD PIN

ERSONAL

DENTIFICATION

UMBER

)

1 2 3

Enter your current PIN and press 3 times.

Press and hold .

Release both buttons. You must now start from the

beginning and reprogram your Wireless Keypad.

Wile holding press and hold for

5 seconds.

Enter your NEW PIN and press .

Enter your TEMPORARY PIN and press .

Press the number of the door you wish to

operate or .

Press any key to operate the door.

Press .

+ AAA -

If the Keypad backlight does not come on, this indicates the

need to replace the batteries.

Figure 3

Press

here

Polarity

markings

Battery

Cover

Press in on the front of the battery cover and slide it down

off of the Keypad.

Remove used batteries and replace

No programming is lost during

replacement of batteries.

with "AAA." Make sure the

batteries are inserted properly

using the polarity markings.

ATTENTION

MODEL AC SR3 OVERHEAD DOOR CORP.

FCC ID: B8Q AC SR3 Residential Door Operator

IC: 2133A-CSD1D 120V. 60HZ. 5A

FOR HELP CALL 1-800-275-6187 OR WWW.OVERHEADDOOR.COM

Interchangeable

Flip-up Cover

available in 3

optional Classic

Colors to match

your home’s

exterior decor

GREEN LED

indicates Pre-Set

toIntellicode® 2

Backlit

Keypad

for Ease

of Use

at Night

Battery

Compartment

2 AAA Batteries

(included)

Program

Button

Covers available in:

s Tan - P/N 37227T

s Almond - P/N 37227U

s Gray - P/N 37227S

s White- - P/N 37227R

STEP 3:

PERATING ONE DOOR OPENER

A To open or close the Garage Door.

s Enter your PIN.

s Press .

FOR CONVENIENCE

Program Keypad BEFORE mounting.

SECTION

Proceed to Section 3 - Mounting Instructions.

NOTE

If the Door does not move,check the LED on Keypad.

If the LED is blinking rapidly,the PIN was entered

incorrectly. After the LED stops blinking,re-enter

your PIN and try again.

Any Keypad Button will control the Door for 30 seconds

after the Door starts moving.

Rapid blinking of the red LED indicates an error. After a

few seconds the LED will turn off. Start over.

Wait until Keypad Backlight turns off (approximately 30 seconds).

STEP 1:

REATING YOUR

STEP 2:

ROGRAMMING

INGLE

OOR

PENER

WIRELESS KEYPAD PIN

ERSONAL

DENTIFICATION

UMBER

)

s Press in order .

s Press .

s Enter your PIN (3 to 8 characters).

s Close keypad cover and wait 30 seconds.

Press .

3 5 7

Figure 1

Press and hold until both LEDs turn BLUE.

s On the Wireless Keypad—enter your PIN.

s Press . LEDs will stay on solid.

s Press again. LEDs will turn off.

s Press again. Door opener should run.

Press any key to stop opener. (It will automatically

stop at the fully open or fully closed position.)

PROGRAM

SET

s Pres

s ,

release again. Long

LED should blink PURPLE

s Release button. Only round LED will be BLUE.

Figure 1

SET

PROGRAM

Open

Travel

Button

ROUND LED

LONG LED

Travel

Button

ON THE OPENER

S/N:10XXXXXXXXXXXX

PROGRAM

A Moving Door can cause serious injury or death.

1 Keep

3 Wall Control should be mounted within sight of door, at least 5 feet above floor and clear of moving parts.

people clear of opening while Door is moving.

2DoNotallow children to play with Wireless Keypad.

4 During programming, the Door Opener could begin to run, so stay away from the moving Door and its parts. To keep

the Door from moving, close the Door and disconnect it from the Opener by pulling the Emergency Release Cord.

WARNING

ASIC

ROGRAMMING FOR

CODEDODGER®

PENERS

If Safety Reverse does not work properly:

1 Close Door and disconnect the opener using Emergency Release Cord.

2 Do not use Door Opener, Remote , or Wireless Keypad.

3 Refer to Door and Door Opener Owner’s Manuals before attempting

any repairs.

CODEDODGER®

ULTIPLE

ENERS

PROGRAMMING FOR

PROGRAM

SET

PROGRAM

SET

This page is for CodeDodger® 2 Only:

If you have an CodeDodger® 1 opener

or openers, go to the reverse side

of this instruction.

CODEDODGER® 2 MODE OF TRANSMISSION

CODEDODGER® 1

PROGRAMMING

INSTRUCTION

PROG

ABC

DEF

GHI

PQRS

TUV

WXYZ

JKL

MNO

STEP 2:

ROGRAMMING

ULTIPLE

OOR

OPENERS

Wait until Keypad Backlight turns off (approximately 30 seconds).

PROGRAM

SET

1 2 3

On your Wireless Keypad:

On your opener’s power head:

s Select first opener and press and hold until

both LEDs turn BLUE.

Press and release again.

LEDs should blink PURPLE.

Enter PIN and press .

Press the number that you have picked for

this door or .

Press 3 times — opener will run.

Repeat procedure below dotted line for remaining openers.

s Release button. Only round LED will be BLUE.

PROGRAM

SET

All Door Openers will use the same PIN.

On your keypad:

s Enter your PIN and press .

s Press again.

s Press the number of Doors (total) you wish

to control ( or ).

ssssssssssssssssssssssssssssssss

Press .

2 3

PROGRAM

Decide which Door will be Door #1, #2 and #3.

Summary of content (2 pages)

PAGE 1
FEATURES : ATTENTION If your garage door opener has a Serial Number sticker which looks like this, in which the first two numbers are 10 or higher, your opener is equipped with CODEDODGER®2. MODEL AC SR3 FCC ID: B8Q AC SR3 IC: 2133A-CSD1D OVERHEAD DOOR CORP. Residential Door Operator 120V. 60HZ. 5A Follow the instructions on this page. This Wireless Keypad is compatible with all CODEDODGER® 1 and CODEDODGER® 2 radio equipped GENIE® products.
PAGE 2
WARNING If Safety Reverse does not work properly: 1 Close Door and disconnect the opener using Emergency Release Cord. 2 Do not use Door Opener, Remote , or Wireless Keypad. 3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs. A Moving Door can cause serious injury or death. 1 Keep people clear of opening while Door is moving. 2 Do Not allow children to play with Wireless Keypad.