Owner's Manual

41360.00092, 02/20
Current Production Openers
1. Press and hold the program button until the round LED
turns blue, then release.
PROGRAM
SET
+
PROGRAM
SET
+
2. The round LED will go out and the long LED will begin
ashing purple.
3. Proceed to STEP 2.
4. Press desired remote
control button 3 times
slowly until door operates.
Openers manufactured between 1995 to 2011 and all
external receivers. (LEARN CODE TYPE)
RADIO
SIGNAL
LEARN
CODE
CODE
LEARN
SET
SET
OPEN
FORCE
CLOSECODE
LEARN LIMITMANUAL
or
RADIO
SIGNAL
LEARN
CODE
RADIO
SIGNAL
LEARN
CODE
NOTE: Learn Code Buttons are normally located under lens covers on
earlier models.
NOTE: The openers LEARN MODE will time out in 30 seconds.
Programming must be completed within 30 seconds.
PROGRAM
SET
+
PROGRAM
SET
+
Pull protective tab to activate remote
STEP 1: PLACE CURRENT PRODUCTION
RESIDENTIAL OPENER INTO PROGRAMMING MODE
FCC Part 15.21 Statement:
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
PRGM
SET
TYPE 1 TYPE 2 TYPE 3
There are 4 types of programming button pads. Type 1 is shown
in these steps. All buttons perform the same function and
programming is the same for all types shown above.
Place operator into programming mode: TYPE
1-2-3-4
+
PRGM
SET
+
–
PRGM
SET
+
–
PRGM
SET
+
–
TYPE 4
WARNING
!
Moving Door can cause serious
injury or death.
•Wall Console must be mounted in sight of door, at least 5
feet above oor and clear of moving parts.
•Keep people clear of opening while door is moving.
•DO NOT allow children to play with the remote or door opener.
If SAFETY REVERSE does not work properly:
•Close door then disconnect opener using the manual release handle.
•Refer to Door and Door Openers Owners Manuals before attempting
any repairs.
Adding a SINGLE (1-2-3-4 Button) Transmitter
1. If operator is in RUN mode, press CAL/RUN key to enter calibration
mode.
2. Press SCROLL (up or down) until display reads “LEARN NEW XMTR?
” Fig.1
• This question along with the instruction “HIT SET FOR YES” will
continuously pan across the display window. (Pressing SCROLL or
CAL/RUN will cancel the operation.)
3. Press SET/CLEAR .
• Display will read “PUSH XMTR BUTTON TWO TIMES TO LEARN
XMTR.”
4. Press Transmitter button two times.
• The display will read “XMTR ___LEARNED.” Where it assigns a
random number to the transmitter. That transmitter is entered
and ready to operate the door.
(Label the transmitter with this
number.)
5. Press SCROLL (up or down) to
move on to another menu item, or
CAL/RUN to exit the CAL mode.
OPEN
CLOSE
STOP
CAL
RUN
SCROLL
SCROLL
SET
CLEAR
LEARN NEW XMTR?
Fig. 1
AVERTISSEMENT
UNE PORTE EN MOUVEMENT PEUT CAUSER DE
GRAVES BLESSURES, VOIRE LA MORT.
N’installez PAS le transmetteur à moins que l’appareil de
sécurité du dispositif de fermeture de porte ne fonctionne
conformément au manuel du dispositif de fermeture de
porte. La console murale doit être montée à la vue de la
porte, à au moins 5 pieds au-dessus du sol et il ne doit y avoir aucune
pièce de porte en mouvement à proximité.
•Éloignez les gens de l’ouverture lorsque la porte est en mouvement.
•NE permettez PAS aux enfants de jouer avec le transmetteur ou le
dispositif de fermeture de porte.
Si l’inversion de sécurité ne fonctionne pas correctement :
•Fermez la porte, puis déconnectez le dispositif d’ouverture à l’aide de
la poignée de dégagement manuel.
•N’utilisez PAS le transmetteur ni le dispositif de fermeture de porte.
•Référez-vous aux manuels du propriétaire de la porte et de l’ouvre-
porte avant de tenter toute réparation.
!
Changing the Battery:
1. Remove vispr clip.
2. Remove small phillips head backing screw.
3. Pry case open with small coin or screwdriver.
4. Remove circuit board.
5. Replace battery with CR2032 coin cell.
PROGRAMMING ASSISTANCE:
If the opener does not activate after the steps shown, repeat steps or
contact Customer Care by website chat
(www.geniecompany.com)
or by phone at: 1-800-354-3643 for programming
assistance. You may also scan this QR code for
additional information and links.
For Patent Information: www.geniecompany.com/patent,
©2020, The Genie Company
Residential Style Transmitters
Commercial Style Transmitters
STEP 1: PLACE OLDER STYLE RESIDENTIAL OPENER
OR EXTERNAL RECEIVER INTO PROGRAMMING
MODE
Place opener into programming mode:
1. Press LEARN CODE button until RED LED begins to blink
then release.
2. Press desired remote control button 3 times or until door
operates.
STEP 1: PLACE COMMERCIAL OPENER INTO
PROGRAMMING MODE
Adding a Single (OPEN/CLOSE/STOP) Transmitter
1. If operator is in RUN mode, press CAL/RUN key to enter calibration
mode.
2. Press SCROLL (up or down) until display reads “LEARN NEW XMTR?
” Fig.1
• This question along with the instruction “HIT SET FOR YES” will
continuously pan across the display window. (Pressing SCROLL or
CAL/RUN will cancel the operation.)
3. Press SET/CLEAR .
• Display will read “PUSH XMTR BUTTON TWO TIMES TO LEARN
XMTR.”
4. Press OPEN Transmitter button two times.
• The display will read “XMTR ___LEARNED.” Where it assigns a
random number to the transmitter. That transmitter is entered
and ready to operate the door.
(Label the transmitter with this
number.)
5. Press SCROLL (up or down) to
move on to another menu item, or
CAL/RUN to exit the CAL mode.
OPEN
CLOSE
STOP
CAL
RUN
SCROLL
SCROLL
SET
CLEAR
LEARN NEW XMTR?
Fig. 1
STEP 1: PLACE COMMERCIAL OPENER INTO
PROGRAMMING MODE