Neakasa NoMo N3 Robot Vacuum USER GUIDE JP ユーザーガイド
User Guide • • • • • • • • • • Safety Information Package Includes About Your Robot Vacuum and Mop About Your Self-Emptying Dustbin LED Indicator Get Started Trouble Shooting Customer Support Care and Maintenance Warranty 1-2 3 4-6 7 8-9 10-15 16-18 19 19-25 26-27 ユーザーガイド • 安全上のご注意 • パッケージに含まれる物 • 各部のなまえ • ロボット掃除機について • 自動ゴミ収集ボックス/充電ステーションについて • ロボット掃除機本体 • 自動ゴミ収集ボックス • 掃除開始 •トラブルシューティング • カスタマーサポート • お手入れとメンテナンス • 保証 28-29 30 31 32-33 34 35 36 37-42 43-45 46 46-52 53-54
Safety Information EN General Warning • Your robot is not a toy. Small children and pets should be supervised when your robot is operating.Children should be supervised to ensure that they do not play with the appliance.
Safety Information EN Battery & Charging Warnings • If the cord or plug is damaged, it must be replaced. • Always disconnect your robot from the charging station before maintenance. • the appliance is only to be used with the power supply unit provided with the appliance. • Charge your robot only with charging station provided. The provided power supply delivers safety extra low voltage corresponding to the input marking on the robot which is required to maintain safe operation.
Package Includes Self-Emptying Dustbin*1 EN Robot Vacuum and Mop*1 Accessories Spining Side Brush*2 Dust Bag*2 Mop Cloth Support*1 Mop Cloth*2 Cleaning Brush*1 (Placed above the dustbin) User Guide*1 HEPA*2 Note: If you find something missing in your package, please contact customer support via support@neakasa.com in time.
About Your Robot Vacuum and Mop EN Front View Recharge button Anti-collision strip WIFI Indicator Power button Anti-collision strip Lidar Infrared sensor Recharge/Spot Cleaning Short press to start the recharge. Press and hold for 3 seconds to start the spot cleaning. On and Off/Cleaning All Short press to start/pause the clean all. Press and hold for 3 seconds to turn the machine on or off. Network Configuration Long press the 2 buttons and for 5 seconds to enter the network configuration.
About Your Robot Vacuum and Mop Bottom View Cliff sensor Universal wheel Spinning side brush Cliff sensor Cliff sensor Right wheel Left wheel Main brush Main brush cover release button 5 EN
About Your Robot Vacuum and Mop EN Side View Charging electrode tip Restart button Short press to restart.
About Your Self-Emptying Dustbin Upper cover Open the upper cover, install/remove the dust bag. Indicator Charging sensor Suction inlet Suck the trash in the Robot vacuum into the dust bag through the suction inlet.
LED Indicator EN Machine Status LED Ring Light Strip Turn on Warm color to cold color, turn red, orange, yellow, purple, blue and green in turn.
LED Indicator EN Status of Light Indicator Light Color The power indicator light changes from warm to cold color for 30s, and it varies with a new status of the machine during the 30s. red, yellow & green The light flashes slowly when collecting dust, and turns off when finishing the dust collection. yellow 1. The light flashes quickly when the dust bag is full, and goes off after 60s. 2. Check whether the dust bag is full when collecting dust.
Get Started EN 1. Get Ready Take your robot and self-emptying dustbin from the package, and set other accessories aside for use. 2. Position the Self-Emptying Dustbin • Place the self-emptying dustbin near an outlet in an area with good Wifi-coverage. • The dustbin should be placed near the wall.
Get Started EN • Ensure there is a space of more than 1.2m/4ft at the front, and more than 0.5m/1.6ft on both sides of the dustbin 1.2 m (3.9 3. Plug in Plug the power cord into the wall. Wrap the cord back so it won't get in the way of the robot as it comes and goes. Put the robot on the flat indoor ground, and remove the protection device of limit bar at both ends of the front bumper. Note: Do not place the charging station under direct sunlight. 4.
Get Started EN 5.Add water and install the mop cloth board. 1. Take out the water tank. 2. Open the cover of the water injection 3. Put on the water inlet cap. port and inject clean water. ( Use only purified water or softened water) 4. Reinstall the water tank. 5. Install the washable cloth on 6. Install the mopboard bracket the mop holder. back to the host.
Get Started EN 6. Wake up NoMo N3 Press and hold the button for 3 seconds to start the robot, and then short press the button recharge automatically. The robot enters the ready state once fully charged. Note: Fully charge the robot before starting cleaning. • Before starting the cleaning, tidy away the wires and articles on the ground to avoid damage caused by winding, dragging and hitting during cleaning. • It is suggested to start the robot at the self-emptying dustbin. 7.
Get Started EN 8. WiFi Connection 2. Register and log in to the account, add device on the home page. 1. The phone is connected to WiFi. (Doesn’t support 5GHz) tutorial video 3. Long press the buttons and to enter the network configuration. for 3 seconds 5. Go to the mobile phone WLAN list and switch your WiFi to Neakasa hotspot. (displays as neakasa_xxx_xxx) 4. Select the connected WiFi of the phone and enter the WiFi password. 6. Back to the App and wait 1-2 minutes to complete the connection.
Get Started EN 9. Cleaning Automatic Recharge/Manual Recharge • When the battery is low during cleaning, or when the cleaning is finished, the robot will automatically recharge. • During cleaning, short press the button , then the robot will return to the self-emptying dustbin to recharge.
Trouble Shooting EN Voice Prompt/Fault Phenomena Possible Causes Solution Please check if the radar is stuck The lidar is blocked or stuck Remove the obstacle or move the machine to an open place and restart it Please check the anti-collision rail The bump sensor is stuck Clean up the foreign matters around the anti-collision rail, or move the machine away Please wipe the cliff sensor and move away from the dangerous area to restart The cliff sensor is triggered after the machine is started up
Trouble Shooting EN Voice Prompt/Fault Phenomena Possible Causes Solution The machine cannot be started up Low battery level or abnormal ambient temperature The battery level is low. Please charge it before use. The ambient temperature is too low (below 0 °C) or too high (above 50 °C). Please use the product in the environment of 0 °C-40 °C Cannot be charged 1. The dust self-emptying dustbin is not electrified 2. The charging electrode tip is dirty 3. The charging electrode tip has poor contact 1.
Trouble Shooting EN Voice Prompt/Fault Phenomena Possible Causes Solution Regular cleaning does not work Low battery Regular cleaning can only be started when the remaining battery level is greater than 30%. Please keep the machine charged every day Cannot be connected to APP Abnormal WiFi network, wrong WiFi password or abnormal APP Network frequency is less than 2.4GHz 1. Please ensure that the machine is in a good WiFi signal area 2. Re-enter the WiFi password or reset WiFi 3.
Customer Support EN If you have other questions or suggestions about your robot, you can visit www.neakasa.com for support tips, frequently asked questions and information about accessories. This information can also be found in the Neakasa App. If you need further assistance, call us at 0800-086-100. Care and Maintenance Care and Maintenance Instructions To keep your robot running at peak performance, perform the procedures on the following pages.
Care and Maintenance EN Replacing Bags When the dust bag is full, the red indicator on self-emptying dustbin charging pile flashes slowly. Please replace the dust bag in time.
Care and Maintenance EN Cleaning the Main Brush Note: The main brush is consumable and should be cleaned at least once a week. It is recommended to replace the main brush every 6-12 months to ensure the cleaning effect. 1. Turn the main unit, press the left and right buckles, and remove the middle sweep cover. 2. Remove the main brush upwards and clean the entangled hair and debris with a cleaning brush.
Care and Maintenance EN Cleaning the Two-in-one Water Tank 1. Press and hold the release button of the two-in-one water tank and at the same time pull it outwards. Dust bin Dust bin snap Release button of two-in-one water tank Water tank cover/Water injection port 2. Open the dust bin by pressing the dust bin snap. 3. Remove the filter screen clip. 4. Take out the filter screen.
Care and Maintenance 5. Remove the debris on the fitter screen and screen clip with a cleaning brush. Note: The filter screen is consumable. It is recommended to replace it every 3-6 weeks. Please make a purchase through the official channel. EN 6. Use the cleaning brush to clean the dust box. It is forbidden to flush the dust box directly with water. 7. Open the water tank cover and inject an appropriate amount of water. Note: It is suggested to use pure water without any cleaning agent. 8.
Care and Maintenance Cleaning Sensors 10. Install the Mop As shown in the figure, put the mop doth fixing strip in the mop cloth fixing slot, attach the mop cloth to the velcro, and then push the mop cloth support horizontally to install it on the robot. Install the washable cloth on the mop holder EN It is recommended to use a clean, soft, dry cloth to wipe each sensor gently every week to ensure the normal use of the machine.
Care and Maintenance EN Cleaning the Self-Emptying Dustbin a. Inspect the sensors and charging contacts to make sure they are clear of debris. Wipe with a clean, dry cloth. Infrared lens*2 Charging and dust collection sensor head*2 Note: Do not spray cleaning solution directly onto sensors or into sensor openings. Infrared lens Charging and dust collection sensor head b.Removing debris from blower cover: Inspect blower cover for any lint or debris built-up, and wipe it with a clean dry cloth to remove.
Warranty EN Warranty Overview Neakasa (‘We’, ‘Our’, ‘Us’) warrants that, subject to the exclusions and limitations set out below, this product (including batteries if applicable) shall be in good working order during the period of one (1) year from the date of purchase (the ‘Warranty Period’).