User's Manual

ManualsBrandsGenex Telecom ManualsElectronicsVHF FM Transceiver

MT-800 PC PROGRAMMER USER’S GUIDE

The main function and frequency of MT-800 is supposed to work for PC

PROGRAMMER.

The usage of this program is SOFTWARE INSTALLATION of WINDOWS OS to

WINDOWS 98(FIRST, SECOND EDITION), WINDOW SERIES, AND WINDOWS XP for

PERSONAL COMPUTER only.

1. INSIDE OF MT-800 PC PROGRAMMER KIT

PROGRAMMING KIT contains following.

1) PROGRAM CD

THE SOFRWARE VERSION SHOWS UP IN THE HELP INFO.

2)MT-800 PROGRAMMING LEAD

2. HARDWARE INSTALLATION

Connect MT-800 programming lead to personal computer com1 or com 2 and

connect the other side to mic connector for finishing hardware

Summary of content (7 pages)

PAGE 1
MT-800 PC PROGRAMMER USER’S GUIDE The main function and frequency of MT-800 is supposed to work for PC PROGRAMMER. The usage of this program is SOFTWARE INSTALLATION of WINDOWS OS to WINDOWS 98(FIRST, SECOND EDITION), WINDOW SERIES, AND WINDOWS XP for PERSONAL COMPUTER only. . 1. INSIDE OF MT-800 PC PROGRAMMER KIT PROGRAMMING KIT contains following. 1) PROGRAM CD THE SOFRWARE VERSION SHOWS UP IN THE HELP INFO. 2)MT-800 PROGRAMMING LEAD 2.
PAGE 2
installation. 3. SOFTWARE INSTALLATION There’s a CD include in the programming kit and inside of CD, there’s program called MT-800.EXE FILE, click that file, then it appears to be like below, and that would be end of the software installation. ※Importance of PC PROGRAM 1) Before start PC PROGRAM, make sure follow steps below.
PAGE 3
WRITE → DISPLAY AT THE LCD MODE BUTTON WRITE NOW → DISPLAY AT THE LCD 1-2) for read MONITOR BUTTON + POWER ON CHANNEL UP OR DOWN BUTTON READ → DISPLAY AT THE LCD MODE BUTTON READ NOW → DISPLAY AT THE LCD 4. Model selection If install MJT-800.EXE file in the computer, it appears model selection block window and will blank, but right now the program is set for only MT-800, so no need to select the extra and get to programming right away. 5.
PAGE 4
1) com port set up This is for hardware setting of port set up only. to port 4. There are port 1 1) PROGRAM READ AND WRITE Read the data from set or write the one. 2) SCAN OPTION SET UP 3-1) SCAN SPEED : 50 ~ 500msec range. Primary stage is 50msec. 3-2) ATTACK TIME : 0 ~ 4 sec range. Primary stage is 0sec. 3-3) RESUME TIME : 1 ~ 10 sec range. Primary stage is 4sec. 3-4) HOME CHANNEL : 1 ~ 32CHANNEL range. Primary stage is 1 CHANNEL. 3) DISPLAY SET UP Can be select set display.
PAGE 5
4) 5) 6) 7) UP LOAD :Up load the new data from PC to Set DOWN LOAD : Down load from the set. PRINT : Can be print. EXIT : Use this for quit from PROGRAM. 7. Setting up for Frequency 1) You can input the frequency form 148MHz to 174MHz every 5KHz – 6.25KHz STEP. 2) NAME section has originally set up CH, every CHANNEL can be input the own name that is possible 8 number or alphabet.
PAGE 6
NOTICE There are no user-serviceable points inside this transceiver. All service jobs must be referred to your Authorization Service Center or Network Administrator Safety/ Warning Information WARNING – DO NOT operate the MT-800 radio when someone (bystanders) outside the vehicle are within following range. Safety Training Information: Antennas used for this transmitter must not exceed an antenna gain of 0 dBd.
PAGE 7
Sample Part 15 Rule Label This device complies with part 15 of FCC Rules. Operation subject to that this device does not cause harmful interference. ! CAUTION ! Device restricted to occupational use to satisfy FCC RF exposure compliance. See owner’s manual for specific operating requirement.