User's Manual

ManualsBrandsGenex Telecom ManualsElectronicsTransceiver, UHF, PTT

GX-80/90 Genex Portable LMR radio

FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL

USE ONLY

The Federal Communications Commission (FCC), with its action in General Docket 93-

62, November 7, 1997, has adopted a safety standard for human exposure to Radio

Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Maxon

subscribes to the same safety standard for the use of its products. Proper operation of

this radio will result in user exposure far below the Occupational Safety and Health Act

(OSHA) and Federal Communications Commission limits.

•This radio is NOT approved for use by the general population in an uncontrolled

environment. This radio is restricted to occupational use, work related operations only

where radio operator must have the knowledge to control the user’s exposure

conditions for satisfying the higher exposure limit allowed for occupational use.

•When transmitting, hold the radio in a vertical position with its microphone 2 inches (5

cm) away from your mouth.

The radio is transmitting when the red LED on the front of the radio is illuminated.

You can cause the radio to transmit by pressing the PTT bar on the radio or, if in VOX

mode, by simply talking above the threshold level set during VOX programming.

DO NOT transmit either in PTT or VOX mode for more than 50% of total radio use time

(50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure

compliance requirements to be exceeded.

These are required operating configurations for meeting FCC RF exposure compliance.

Failure to observe these restrictions mean violation.

This equipment complies with the FCC RF Exposure Limits for controlled environments.

- Function description

1. power on& volume control

(1) Power On

Turn radio on by turning the power/volume Rotary switch clockwise out of

detent. When radio turns on, it make beep sound.

(2) Power Off

Turning the power /volume rotary switch counterclockwise out of detent

(3) Volume up/down

Adjusting level of volume by turning Volume rotary switch.

Summary of content (6 pages)

PAGE 1
GX-80/90 Genex Portable LMR radio FCC RF EXPOSURE COMPLIANCE REQUIREMENTS FOR OCCUPATIONAL USE ONLY The Federal Communications Commission (FCC), with its action in General Docket 9362, November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Maxon subscribes to the same safety standard for the use of its products.
PAGE 2
. Channel Selecting (Up/Down) User can choose a channel by adjusting Channel rotary switch 3. RX Operation 1) Busy condition is that unit is receiving a signal fixed in its channel Unit in the busy condition will be operated according to a fixed input of tone and two Tone.
PAGE 3
scan delay time has expired. Scanning will continue until the channel is changed or press scan button again. - Scan channel Delete : To temporarily delete a channel from the scan list, simply press the scan button for a short time while stopped on the channel to be detected. This will remove that channel from the scan list until the channel is changed or the radio’s power is reset.
PAGE 4
- Muti Scan : if press Scan key while Priority scan mode is On, Priority Channel scan and Normal scan will take place at the same time under this condition, scan sequence will be as below. N-Ch(1) ===Î P-Ch ==Î N-Ch(2)===Î P-Ch ===Î N-Ch(3)…… 4. TX operation 1) PTT TX Allows transmission with pressing PTT. 2) To enable VOX function, first of all VOX function and its level must be set through PC programmer and then turn Radio ` on while pressing PTT. At a moment, radio makes beep sound.
PAGE 5
In this condition, allows only RX. 3) Power save delay. Power save mode can be cancelled whenever occurs key/TX event. This function forces radio not to go back to Power save mode during Power save delay time that is programmable. 4)Power Save Sequence Power Save Delay ==Î Power Save On ===Î Power Save Off ====Î Power save off …. 6. Low Battery Detection 1) RX Low battery If Low battery condition is detected, Radio flash LED with beep sound.
PAGE 6
4) Once Master and slave radio is set, Please press PTT of Master radio to transmit data.