Node B Installation Guide Node B V2 Installation Guide Version 5.0.
Node B Installation Guide Information in this document and the products described are subject to change without notice. 2000-2003 IPWireless, Inc. All rights reserved. Reproduction, alteration, or distribution in any manner whatsover without the written permission of IPWireless Inc, is strictly forbidden. Trademarks used in this text: the IPWireless logo, icon and IPWireless Broadband Modeem are trademarks of IPWireless, Inc.
Node B Installation Guide Table of Contents 1. Release Version ..............................................................................................5 2. Safety Precautions..........................................................................................6 3. General Warnings ...........................................................................................6 4. Overview ..........................................................................................................
Node B Installation Guide Table of Tables Table 2-1 : Safety Sumbols...................................................................................................... 6 Table 5-1 : Specifications......................................................................................................... 8 Table 5-2 : Node B Model Types ............................................................................................. 9 Table 6-1 : Packing List.....................................................
Node B Installation Guide 1. Release Version Date th 8 April 2003 Version 5.0.0 Version Author Reason For Change Issue 5.0.0 L.
Node B Installation Guide 2. Safety Precautions Table 2-1 : Safety Sumbols GENERAL WARNING GENERAL SAFETY PRECAUTION ELECTRICAL HAZARD BURN/HEAT HAZARD CORROSIVE MATERIALS GROUND VOLTAGE: HEAT: CORROSIVE: GROUND: Direct contact with these areas could result in severe physical harm and property damage Direct contact with this surface will result in severe burns Direct contact with this surface will result in chemical burns.
Node B Installation Guide 4. Overview Node B is the European Technical Standards Institute’s (ETSI) name for the radio base station. The basic function of the Node B is to convert 100 Base T packet data into the UTRAN TD-CDMA air interface used between the Node B and the 3G Modem. The Node B can be configured to operate in configurations ranging from a single sector or omni mode, up to a 6 sector arrangement.
Node B Installation Guide 5. General Specifications Table 5-1 : Specifications Unit Specification 566 H x 380 W x 202 D mm Measurements 22.5 H x 15 W x 8 D inch Measurements with Solar Shield attached 566 H x 380 W x 294 D mm 22.5 H x 15 W x 11.
Node B Installation Guide Table 5-2 : Node B Model Types Node B Frequency Model Number 1900-1905 MHz Model GM 1905-1910 MHz Model GN 1910-1915 MHz Model GP 1915-1920 MHz Model GQ 2053-2082 MHz Model HV 2010-2015 MHz Model JG 2500-2686 MHz Model HZ Figure 5-2 : General Description 406mm 406mm 10" 202mm NODE B UNIT 560mm 560mm ACCESS COVER GPS ANTENNA CONNECTIONS MOUNTING BRACKET CABLE GLANDS RF ANTENNA CONNECTIONS Version 5.0.
Node B Installation Guide 6. Installation This section describes the steps to be followed to physically install the Node B. Step 1- Pre-Installation This section describes the initial checks that should be carried out to ensure that preparation for the installation is complete. For Installation Check Card please see Appendix A at the back of this manual. 1. Review site construction drawings to determine if site was constructed according to the drawings. 2.
Node B Installation Guide Step 2 – Parts Shipped & Tools Required This section reviews the parts, ancillary materials and tools required to install the Node B. Use this checklist to check quantity and quality of parts as they are unpacked: The Node B unit is packaged with the following items, the packing list on the inside top of the packing shall list these items. The carton is packed to facilitate the intended sequence of installation. The figure below shows the sequence of removal from the packing.
Node B Installation Guide In addition to standard construction equipment, the following tools and materials should be available prior to installation: Table 6-2 : Tools Required Tools Description Access Tool Tool for Node B service area access Drill and Drill Bits M6 or No8 Masonry Drill Bit Voltmeter Fluke meter Alarm Cable Insertion Tool 1mm flat blade Screwdriver Basic telecommunications tool kit Includes screwdriver, socket wrenches, etc.
Node B Installation Guide Step 3 Site Preparations for Node B Installation The section specifies the facilities that need to be available at the site prior to installation. The table below is a site checklist that should be completed prior to installation. It is assumed that the site has already been selected from RF network planning and that site acquisition or permission has been granted.
Node B Installation Guide General Considerations The following consideration and checks are applicable to all mounting types :- Ø Consider the earthquake zone requirements for the given site being considered and ensure that the mounting arrangement and location complies. Ø Review the GPS installation guidelines (Step 7) to ensure that the location will allow proper operation of the Node B GPS remote antenna. i.e.
Node B Installation Guide Step 4 Mounting Bracket Installations There are three ways of installing the Node B:- Ø Wall, Ø Pole Ø Rack Mounts. This section explains how to mount the Node B bracket in all three instances. The securing of the Node B to the mounting bracket is the same for the three mounts and shall be described in step 10. Mounting Bracket The figure below illustrates the key features of the mounting bracket.
