Generac Wireless Display System Instruction Manual Preliminary Proof #2 07/20/07
Table of Contents TABLE OF CONTENTS SAFETY SAFETY ...................................... Inside Front Cover This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: Read This Manual Thoroughly .....................IFC Operation and Maintenance ............................ 3 How to Obtain Service ..................................... 3 INTRODUCTION .................................................... 3 • This device may not cause harmful interference.
Wireless Display System be copied and posted in potential hazard areas. Safety should be stressed to all operation operators, potential operators, and service and repair technicians for this equipment. SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe followed during installation and maintenance of the generator and batteries.
Wireless Display System • Inspect the generator regularly, and promptly repair or replace all worn, damaged or defective parts using only factory-approved parts. • Before performing any maintenance on the generator, disconnect its battery cables to prevent accidental start-up. Disconnect the cable from the battery post indicated by a NEGATIVE, NEG or (–) first. Reconnect that cable last. • Never use the generator or any of its parts as a step.
Wireless Display System OPERATION AND MAINTENANCE The operator is responsible for proper and safe use of the equipment. The manufacturer strongly recommends that the operator read this Owner's Manual and thoroughly understand all instructions before using this equipment. The manufacturer also strongly recommends instructing other users to properly start and operate the unit. This prepares them if they need to operate the equipment in an emergency.
Wireless Display System INSTALLATION For easier installation, the batteries should first be fitted into the display unit (Figure 1). This will allow you to walk around and find the best location for the unit while still receiving good signal strength. Attach the other transceiver to the generator and mount it as high as possible, preferably away from any structures to get a maximum signal. Figure 1 — Open Display Unit 1. Insert the batteries (Figure 2). Figure 2 — Insert Batteries 4.
Wireless Display System 13. Set the time and date into the clock, use the instructions given in the "Time and Date Menu" section. The time & date will be remembered even if the battery goes dead. There is a separate, replaceable 10 year battery for this function. 14. The communications LED will light solid to show data is being received. A flashing LED indicates the unit was unable to find the generator. 15. Set an exercise day and time now (see "Exercise Menu" section).
Wireless Display System ALARM AND STATUS DISPLAY Figure 8 — Menu System The display will normally show the operating status of the generator or an alarm message if one is present. See Figures 6 and 7.
Wireless Display System If the generator can run at a low speed (Quiet Test QT), this option is available. If there is an automatic transfer switch, there is the option to run the generator and transfer onto generator power. Once the generator is started or stopped, the state of the generator will be shown by a “*” symbol next to the command issued. For example: Normal Start* You started the generator at normal speed.
Wireless Display System EXERCISE MENU CHANGING CHANNELS Normally the exercise time is set on the generator control board as it powers up. If an exercise time has not been set on the control board, all it’s LED’s will flash and an alarm will be set on the wireless display – “EXERCISE TIME NOT SET”. Channel selection is normally automatic, manually changing channels should only need to be done if experiencing interference from other equipment.
Wireless Display System 2. Disconnect the transceiver at the generator end, then reconnect it. You now have one (1) minute to complete the setup process. 3. On the display select “Reset Radio”. The display will show it is searching for the generator, this process will last one minute and a countdown timer will be displayed. 4. Once the time is up a message will be displayed showing that the generator has been found. The radio settings will be remembered for the next time. 5. Re-set the exercise time.
MENU MAP + T Up STATUS Display Status Information GRAPH Graph - Generator Battery Voltage - Generator RPM - Current - Utility Voltage TIME & DATE Set the Clock and Calendar RADIO 1. 2. 3. 4. 5. Down t Time EMAIL ALARMS L O G Show Radio Information Change Channels Reset Radio Add New Display Test Radio Link EXERCISE Set an Exercise Time and Day Select Low or High Speed Exercise SETTINGS 1. 2. 3. 4. 5.