7300 Series Operating Manual Genelec 7360A and 7370A Smart Active Subwoofers 750-7360A/7370A
Genelec 7360A and 7370A Smart Active Subwoofers Introduction Analogue Output 1 thru 7 Congratulations and a thank-you for the purchase of this Genelec 7300 series subwoofer. This manual addresses setting up and using the Genelec 7360A and 7370A subwoofers. These subwoofers are designed to integrate easily into all environments, both those using analogue audio as well as those using digital AES/EBU audio.
BYPASS SWITCH CONNECTOR 7360A SMART ACTIVE SUBWOOFER AVERTISSEMENT WARNING CONTROL SWITCHES BASS ROLL-OFF PHASE DIGITAL LFE LFE CHANNEL LFE +10 dB LEVEL THIS DEVICE COMPLIES WITH FCC PART 15 AND CANADIAN ICES-003 RADIO FREQUENCY CLASS B EMISSION REQUIREMENTS. REFER TO OPERATING MANUAL FOR FULL INFORMATION. -4 dB -8 dB -90° -180° ON/OFF A/B -10 dB -20 dB TEST TONE ISS STORED INPUT dBu PRODUCING 100 dB SPL (1 m) ON OFF 0 -2 -4 www.genelec.com Figure 1. Connector panel of the 7360A.
• • • • pointing upwards and the microphone top at the height of the engineer’s ear. The microphone is a part of the GLM User Kit. Connect the microphone cable to the microphone input in the GLM Adapter device. Download the GLM software at the Genelec web site (www.genelec.com). Install the GLM software and follow the instructions in the software to measure and set up your system.
adjusts the phase automatically, but if GLM is not available, the following manual phase matching can be applied. Manual Phase Adjustment Method Genelec 7360A and 7370A subwoofers are equipped with a built-in 85 Hz frequency test tone generator for phase alignment. The test tone generator is connected to the subwoofer's "TEST 1" output. Connect temporarily a monitor to this output for manual phase alignment. Power up the system and set the TEST TONE switch to "ON.
2. First calibrate the level between the subwoofer and all main monitors using the rotary level adjustment trimmer on the subwoofer and suitable test signals. +100 Level vs Freq (Hz) Bass Roll-Off -4, -8 and -12 dB 7360A 25.4.16 +100 Bass Roll-Off -4, -8 and -12 dB LFE channel 4. Repeat phases 1 to 3 with all other subwoofers in the chain, one by one. 5. When two subwoofers connected in this way are positioned close to one another, bass level increases by 6 dB.
SPECIFICATIONS Model 7360A 7370A Lower cut-off frequency -6 dB 19 Hz 19 Hz Upper cut-off frequency -6 dB (main channel/LFE) 100 Hz/150 Hz 100 Hz/150 Hz Accuracy of frequency response +/-3 dB 19 Hz - 100 Hz 19 Hz - 100 Hz Driver 250 mm (10 in) (magnetically shielded) 305 mm (12 in) (no magnetical shielding) Harmonic distortion at 1 m on axis in half space, 30 to 85 Hz 2nd ≤ 3% @ 90 dB SPL 3rd ≤ 2% @ 90 dB SPL 2nd ≤ 3% @ 95 dB SPL 3rd ≤ 3% @ 95 dB SPL Maximum short term sine wave SPL output
7360A and 7370A Operating Manual www.genelec.com Genelec Document D0134R001a. Copyright Genelec Oy 9.2016. All data subject to change without prior notice International enquiries: In the U.S. please contact: In China please contact: In Sweden please contact Genelec, Olvitie 5 Genelec, Inc.