V1.2 SELD A10 User Guide Gen2Wave Co.
Device Features Barcode Reader Fingerprint reader E-Passport/ID reader antenna Camera / Flash Iris reader Temperature measurement sensor Power button Left function button Battery cover Right function button Lock button Universe mount HID RFID antenna USB-C Connector (male) Power / Charging status LED MSR reader IC card reader 2 USB-C Connector (female) OCR reader
Application installation / installation on A10 of smartphone Application Installation ① Download the application below from the link provided separately. SLEDA10TEST_x.x.x.apk : This is the main application for testing each function of A10. GemPCSC_Service_V1.5.apk : This is a service application for IC card testing. G2w-USBCamTest_x.x.x.x.apk : This is an application for camera testing. card-reader-manager-1.9.01.apk : This is an application for testing fingerprint.
Power interface(1) Power ON : Press the A10 power button for about 0.5 seconds. The A10 A10 power status LED lights up blue. Power OFF : Press the A10 power button for about 3 seconds. A10 A10 power status LED turns off. Smartphone charging with A10 : With the A10 powered off, press the right and left function buttons simultaneously for 1 second. The A10 power status LED flashes blue.
Power interface(2) Power on ① After mounting the A10 on the smartphone, press the power button for 0.5 seconds, the A10 power LED turns on and the A10 power turns on. * If the A10 demo app is installed on your smartphone, the demo app will run automatically when the power of A10 is turned on. * If the smartphone is not mounted on the A10, the power LED of the A10 blinks when the power of the A10 is turned on, and the power LED of the A10 turns on when the smartphone is mounted on the A10.
Charging interface A10 charging ① The A10 battery can be charged by plugging in power to the A10 USB-C port. ② Regardless of the A10 power status, it can always be charged. ③ When charging, the charging status LED of the A10 lights up, red when charging, and green when charging is complete. Smartphone charging ① If charge the A10 when the A10 power is off, the A10 and the smartphone are charged at the same time.
How to use functions Currently, only sample tests are available for each function. If a problem occurs while using the program, close the program and run it again. Caution. 7 When running or reading a program, you should always allow USB permission and access permission pop-ups at the bottom of the screen.
Thermometer Thermometer ① BODY Temperature Mode : Need to check it to take your body temperature. ② Celsius Unit : When checked, the temperature is displayed in Celsius, when unchecked, the temperature is displayed in Fahrenheit. ③ Select “THERMAL READER”. ④ Can measure the temperature of the object by pressing the "READ THERMAL" button with a distance of about 1 ~ 3cm from the object to be measured. The sensed temperature is displayed as Thermal Read Value is XX.XX.
Barcode Scanner Barcode Scanner ① 9 Select “SCANNER SCANNER”. Can read barcodes by pressing the right or left function button or the scan button on the screen. A laser aimer should be on the center of barcodes to get a successful read.
Magnetic Stripe Reader Magnetic Stripe Reader ① Select “Magnetic Stripe Reader”. 10 MSR data can be read along the rail from top to bottom with the magnetic line visible as shown in the picture below.
HID RFID HID RFID ① Select “HID RFID”. 11 If see the phrase “Waiting for card” on the screen as shown in the picture, place the card on the antenna of the device and read.
Smart Card / SAM Smart Card / SAM ① 12 Select “SMART CARD / SAM”. To read an smart card, insert the smart card into the smart card slot at the bottom of the A10 and press the "READ SMART CARD" button on the screen to view the ATR data. Insert the SAM card into the built-in SAM card slot and press the "READ SAM" button to view the ATR data.
Passport / ID card Reader Passport / ID card reader ① Select “PASSPORT READER”. Wait a few seconds for the program to run 1) OCR data can be read along the rail from top to bottom with the MRZ line visible as shown in the picture below. 2) Place the Passport or ID Card Chip on the back of the top of the A10.
Fingerprint reader (Suprema) Fingerprint reader ① 14 Select “FINGERPRINT READER”. After entering the User Name in Enroll, press the “START BUTTON” to register the fingerprint. Can search for fingerprint by selecting “START BUTTON”.
Fingerprint reader (IB) Fingerprint reader ① Select “FINGER READER”. Select "Single flat finger" in the program's Capture item and click the "Start" button to read Fingerprints. When reading a fingerprint, you need to touch your finger on the outside (gray) of the fingerprint reader sensor shown in the picture to read.
Camera Camera ① Select “CAMERA”. Caution. 16 When press the shoot button, the image shown in the preview is saved. The camera app is a demo version. It will be modified so that all functions can be used in the future.
Informaion for FCC manual Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.