User's Manual
Talon Auto-Grip Wireless Charger
IC ID: 21530-100251 Instruction Manual
FCC ID: 2AGR4-100251
1. Wireless charging area
2. Infrared sensors for auto grip feature
3. Status indicator
4. USB Type-C input port
5. Spring grip air vent holder
6. Grip release button: press to release cell phone from holder
7. Rotate knob to unlock/lock swivel mount so that the unit can be rotated
for optimal user viewing
For your safety, please read this manual carefully before using this product
Applicable Devices
Devices with built-in wireless charging receiver(iPhone8/8Plus,iPhoneX,
Samsung S6,S7,S8,Note8)
Operation
1. Attach spring clip to your dash board vent.
2. Plug USB-C plug into the charging unit, and connect USB-A into the car
charging port.
3. The LED light will activate “RED” – unit is in standby mode and ready to
charge your device.
4. Place cell phone near the infrared sensors (#2), the gripping arms will
sense your device and automatically open, place your device on the
charging surface, the gripping arms will automatically retract and hold
your device.
5. Your device will start to charging, LED Indicator will activate Blue when
charging.
6. To release your device, hold your device and press the release button
(#6), the gripping arms will open, and you can remove your device.
(The gripping arms are spring loaded so there will be no damage if you
accidentally remove your device without activating the release mechanism).
7. If your device has any metal between the charging surface and the
back of the device the unit will not charge, the LED indicator will be
Blue, please review step 6 to remove the device. Remove any metal
objects between your device and the charging surface.
Standard Accessories
1. Wireless charger
2. User manual
3. USB-C cable
4. Car air vent clip with adjustable swivel mount
Specification
1. Input: 5V 2A/ 9V 2A/ 12V 2A
2. Output: 5V 1A/ 9V 1.2A/ 9V 1.67A
3. Charging distance: <5mm
4.USB Type-C input port
2.Infrared sensors
for auto grip
feature
5.Spring grip air vent
holder
1.Wireless charging area
3.Status indicator
6.Grip release button: press
to release cell phone from
holder
7.Rotate knob to unlock/lock swivel
mount so that the unit can be
rotated for optimal user viewing
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules. Operation
is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this devicemust
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not explicitly approved by
the partyresponsible for compliance could void the user's authority tooperate
this equipment.
Note: this equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
canradiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference toradio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged totry to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. During the operation of device a distance of 15
cm surrounding the device and 20 cm above the top surface of the device
must be respected.
This device complies with Part 18 of the FCC Rules. This equipment
generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
● Increase the separation between the equipment and any other radio device.
● Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ISED Statement
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
● This device may not cause interference; and
● This device must accept any interference, including interference that may
cause undesired operation of the device. Le présent appareil est conforme
aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
● l’appareil ne doit pas produire de brouillage;
● l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment complies with Canada radiation exposure limits set forth for
an uncontrolled environment.
During the operation of device a distance of 10 cm surrounding the device
and 10 cm above the top surface of the device must be respected.
Cet équipement est conforme Canada limites d'exposition aux radiations
dans un environnement non contrôlé.
au cours de l'opération de l'appareil sur une distance de 10 cm autour de
l'appareil et de 10 cm au - dessus de la surface supérieure de l'appareil
doit être respecté.