GWM400 Product Technical Specification and User Guide Version: DocId: 03 GWM400_HID_v03 M2M.GEMALTO.
GWM400 Product Technical Specification and User Guide Page 2 of 38 2 Document Name: GWM400 Product Technical Specification and User Guide Version: 03 Date: 2017-07-05 DocId: GWM400_HID_v03 Status Confidential / Prelimenary GENERAL NOTE THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PRODUCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL.
GWM400 Product Technical Specification and User Guide Page 3 of 38 Contents 125 Contents 0 Document History ...................................................................................................... 7 1 Introduction ................................................................................................................. 8 1.1 Related Documents ........................................................................................... 9 1.2 Terms and Abbreviations ..................
GWM400 Product Technical Specification and User Guide Page 4 of 38 Contents 125 6 Full Type Approval.................................................................................................... 34 6.1 Gemalto M2M Reference Setup ...................................................................... 34 6.2 Restrictions ...................................................................................................... 35 6.3 CE Conformity..........................................................
GWM400 Product Technical Specification and User Guide Page 5 of 38 Tables 5 Tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Table 7: Table 8: Table 9: Table 10: Table 11: Table 12: Table 13: Table 14: Table 15: Table 16: Table 17: Terms and abbreviations................................................................................... 9 Directives ........................................................................................................
GWM400 Product Technical Specification and User Guide Page 6 of 38 Figures 6 Figures Figure 1: Figure 2: Figure 3: Figure 4: Figure 5: Figure 6: Figure 7: Figure 8: Figure 9: Figure 10: Figure 11: Sample GWM400 labels (This is a label under working, subject to further editing)................................ 15 GWM400 interfaces ........................................................................................ 18 Block diagram ....................................................................
GWM400 Product Technical Specification and User Guide Page 7 of 38 0 Document History 7 0 Document History Preceding document: "Cinterion® GWM400 Product Technical Specification and User Guide” v02 New document: "Cinterion® GWM400 Product Technical Specification and User Guide" v02 Chapter What is new 3.4 Updated max. supply power in Table 10 3.5.
GWM400 Product Technical Specification and User Guide Page 8 of 38 1 Introduction 15 1 Introduction This document1 describes the hardware of the GWM400. The GWM400 contains a Cinterion® ELS61-AUS module, and has an RS-232 compatible interface with an 8-pin Molex Microfit connector, including power supply, and an RF antenna connector. The scope of this document includes interface specifications, electrical as well as mechanical characteristics of the GWM400.
GWM400 Product Technical Specification and User Guide Page 9 of 38 1.1 Related Documents 15 1.1 [1] [2] Related Documents AT Command Set for the Cinterion® ELS61-AUS module Release Notes for the Cinterion® ELS61-AUS module To visit the Gemalto M2M GmbH Website please use the following link: http://m2m.gemalto.com 1.
GWM400 Product Technical Specification and User Guide Page 10 of 38 1.
GWM400 Product Technical Specification and User Guide Page 11 of 38 1.3 Regulatory and Type Approval Information 15 1.3 Regulatory and Type Approval Information 1.3.1 Directives and Standards GWM400 is designed to comply with the directives and standards listed below.
GWM400 Product Technical Specification and User Guide Page 12 of 38 1.3 Regulatory and Type Approval Information 15 Draft ETSI EN 301 489-52 V1.1.0 Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 52: Specific conditions for Cellular Communication Mobile and portable (UE) radio and ancillary equipment; Harmonized Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/ EU Draft ETSI EN 301 489-01 V2.2.
GWM400 Product Technical Specification and User Guide Page 13 of 38 1.3 Regulatory and Type Approval Information 15 Table 5: Standards of European type approval Draft ETSI EN 301 489-01 V2.2.0 ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonized Standard covering the essential requirements of article 3.
GWM400 Product Technical Specification and User Guide Page 14 of 38 1.3 Regulatory and Type Approval Information 15 1.3.2 Safety Precautions The following safety precautions must be observed during all phases of the operation, usage, service or repair of any cellular terminal or mobile incorporating GWM400.
GWM400 Product Technical Specification and User Guide Page 15 of 38 1.4 Product Label 15 1.4 Product Label The labels fixed to the bottom of a GWM400 comprise the following information. 2 1 3 4 5 7 6 8 9 11 12 10 Figure 1: Sample GWM400 labels (This is a label under working, subject to further editing) Table 7: GWM400 label information No.
GWM400 Product Technical Specification and User Guide Page 16 of 38 2 Product Concept 17 2 Product Concept 2.1 Key Features at a Glance Feature Implementation General Incorporates Cinterion® The Java module handles all signal and data processing within the Java module GWM400. Internal software runs the application interface and the complete WCDMA/LTE protocol stack.
GWM400 Product Technical Specification and User Guide Page 17 of 38 2.1 Key Features at a Glance 17 Feature Implementation Java™ Open Platform Java™ Open Platform with • Java™ profile IMP-NG & CLDC 1.
GWM400 Product Technical Specification and User Guide Page 18 of 38 3 Interface Description 25 3 Interface Description 3.1 Overview GWM400 provide the following interfaces for power supply, operating status indication, antenna, SIM card and data transfer: Table 8: GWM400‘ interfaces No.
GWM400 Product Technical Specification and User Guide Page 19 of 38 3.2 Block Diagram 25 3.2 Block Diagram Figure 3 shows a block diagram of a sample configuration that incorporates a GWM400 and typical accessories.
GWM400 Product Technical Specification and User Guide Page 20 of 38 3.3 Operating Modes 25 3.3 Operating Modes The table below briefly summarizes the various operating modes referred to in the following chapters. Table 9: Overview of operating modes Normal operation UMTS / HSPA / LTE Power saving set automatically when no call is in progSLEEP ress. UMTS / HSPA / LTE Power saving disabled, but no call in progress. IDLE UMTS DATA UMTS data transfer in progress.
GWM400 Product Technical Specification and User Guide Page 21 of 38 3.4 Molex Microfit Connector 25 3.4 Molex Microfit Connector Via the 8-pin Molex Microfit connector, the host application controller controls the GWM400 (including power supply), and transports data. Figure 4: Pin assignment Molex Microfit Table 10: 8-pin Molex Microfit connector Pin no. Signal name I/O Function 1 BATT+ I Power Supply (4.75-32V DC; 3.
GWM400 Product Technical Specification and User Guide Page 22 of 38 3.4 Molex Microfit Connector 25 3.4.1 RS-232 Interface The RS-232 interface is implemented as a serial asynchronous transmitter and receiver conforming to ITU-T V.24 Interchange Circuits DCE.
GWM400 Product Technical Specification and User Guide Page 23 of 38 3.5 Power Up/Power Down Scenarios 25 3.5 Power Up/Power Down Scenarios In general, be sure not to turn on the GWM400 while it is beyond the safety limits of voltage stated in Section 4.1. GWM400 immediately switches off after having started and detected these inappropriate conditions. In extreme cases this can cause permanent damage to the GWM400. 3.5.
GWM400 Product Technical Specification and User Guide Page 24 of 38 3.6 SIM Interface 25 3.6 SIM Interface The SIM interface is intended for 1.8V and 3V SIM cards in accordance with 3GPP 31.102. The card holder is a five wire interface according to ETSI 102 221. The SIM card holder is protected by a rubber cover that has to be opened before a SIM can be inserted.
GWM400 Product Technical Specification and User Guide Page 25 of 38 3.8 RF Antenna Interface 25 3.8 RF Antenna Interface An external RF antenna is connected via the GWM400’s SMA connector (jack) that is also the antenna reference point (ARP). SMA connector (jack) Figure 7: Antenna connector The system impedance is 50. In any case, for good RF performance, the return loss of the customer application’s antenna should be better than 10dB (VSWR < 2).
Page 26 of 38 GWM400 Product Technical Specification and User Guide 4 Electrical and Environmental Characteristics 30 4 Electrical and Environmental Characteristics 4.1 Absolute Maximum Ratings Table 11: Absolute maximum ratings Parameter Port / Description Min. Max. Unit Supply voltage BATT+ -0.3 +45 V RS-232 input voltage range TXD0, DTR0, RTS0 -25 +25 V RS-232 output voltage range RXD0, CTS0, DCD0 -13.2 +13.
GWM400 Product Technical Specification and User Guide Page 27 of 38 4.2 Power Supply Ratings 30 4.2 Power Supply Ratings Table 13: Power supply specification IBATT+ 1 Description Conditions OFF State supply current Power Down 13.6 mA UMTS Max output power 254 mA LTE Max output power 368 mA IDLE @ DRX=6 (UART active, but no communication) 16.
Page 28 of 38 GWM400 Product Technical Specification and User Guide 4.3 Operating Temperatures 30 4.3 Operating Temperatures Table 14: Temperature characteristics Parameter Min Normal operation (ambient temperature) -30 Typical Max Unit +75 °C Note: Within the specified normal operating temperature range the board temperature may vary to a great extent depending on operating mode, used frequency band, radio output power and current supply voltage.
Page 29 of 38 GWM400 Product Technical Specification and User Guide 4.4 Antenna Interface 30 4.4 Antenna Interface Table 15 lists RF antenna interface specifications for the GWM400. Please note that the specified conditions may not apply to or be supported by all terminals. Table 15: RF Antenna interface UMTS/LTE Parameter Conditions Min. Typical Max. Unit UMTS/HSPA connectivity Band I,V,VIII Receiver Input Sensitivity@ARP UMTS 2100 Band I -106.7 dBm UMTS 850 Band V -106.
GWM400 Product Technical Specification and User Guide Page 30 of 38 4.5 Storage Conditions 30 4.5 Storage Conditions Table 16: Storage conditions Type Condition Unit Reference Air temperature: Low High -25 +40 °C IPC/JEDEC J-STD-033A Humidity relative: Low High 10 90 at 40°C % --IPC/JEDEC J-STD-033A Air pressure: Low High 70 106 kPa IEC TR 60271-3-1: 1K4 IEC TR 60271-3-1: 1K4 Movement of surrounding air 1.
GWM400 Product Technical Specification and User Guide Page 31 of 38 5 Mechanics, Mounting and Packaging 33 5 Mechanics, Mounting and Packaging 5.1 Mechanical Dimensions Figure 8 shows a 3D view of the GWM400 and provides an overview of the mechanical dimensions of the terminal. For further details and an exploded view see Figure 9. Length: Width: Height: 71.3mm (excluding SMA antenna connector) 76.7mm (including SMA antenna connector) 51.5mm 23.
GWM400 Product Technical Specification and User Guide Page 32 of 125 5.
GWM400 Product Technical Specification and User Guide Page 33 of 38 5.2 Packaging 33 5.2 Packaging GWM400 terminal units come in bubble bags stashed into VP boxes made out of corrugated fiberboard: • VP box size: 370mm x 350mm x 155mm A VP box contains up to 60 terminal units, stashed into two layers of up to 30 units. Terminal layers are separated by foam layers for protective purposes. 1 475.00241.
Page 34 of 38 GWM400 Product Technical Specification and User Guide 6 Full Type Approval 36 6 Full Type Approval 6.
GWM400 Product Technical Specification and User Guide Page 35 of 38 6.2 Restrictions 36 6.2 Restrictions Later enhancements and modifications beyond the certified configuration require extra approvals. Each supplementary approval process includes submittal of the technical documentation as well as testing of the changes made. • No further approvals are required for customer applications that comply with the approved GWM400 configuration.
GWM400 Product Technical Specification and User Guide Page 36 of 38 6.5 Compliance with FCC Rules and Regulations 36 6.5 Compliance with FCC Rules and Regulations As an integrated product, GWM400 is fully compliant with the grant of the FCC Equipment Authorization for the built-in Java modules, and therefore, bears the labels “Contains FCC ID: QIPELS61-AUS”.
GWM400 Product Technical Specification and User Guide Page 37 of 38 7 List of Parts and Accessories 37 7 List of Parts and Accessories Table 17: List of parts and accessories Description Supplier Ordering information GWM400 Gemalto Ordering number L30960-N4300-A200 8-pin receptacle Molex Microfit (3.
About Gemalto Gemalto (Euronext NL0000400653 GTO) is the world leader in digital security with 2015 annual revenues of €3.1 billion and blue-chip customers in over 180 countries. Our 14,000+ employees operate out of 118 offices, 45 personalization and data centers, and 27 research and software development centers located in 49 countries. Gemalto develops secure embedded software and secure products which we design and personalize.
