® 4x4 VGA Matrix EXT-VGAAUD-444 User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday Pacific Time Write To: Gefen LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen LLC reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Panel Descriptions 6 Connecting And Operating The 4x4 VGA Matrix 7 IR Remote Description 8 4x4 VGA Matrix Remote Installation 9 Using the IR Remote Control Unit 10 RS-232 Interface 11 Rack Mount Installation 12 Specifications 13 Warranty
INTRODUCTION Congratulations on your purchase of the 4x4 VGA Matrix. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 4X4 VGA MATRIX • The 4x4 VGA Matrix does not transmit display information (EDID) to the source. Standard VESA resolutions should be output by most computers without the need of an EDID. If using a non-VESA standard resolution or if EDID is needed, an EDID storage and relay device is necessary. Gefen recommends the use of a DVI Detective (part# EXT-DVI-EDIDN) with two VGA to DVI adapters.
FEATURES Features • Switches easily between any four VGA/Analog Audio sources • Sends up to four VGA inputs with Analog Audio to any four displays with Analog Audio • Supports high-definition VGA up to 1920 x 1200 resolution at 60 Hz • LED lights on the front panel show selected VGA routes • RS-232 Control • Includes discrete IR remote control Package Includes (1) Gefen 4x4 VGA Matrix (4) 6 ft. VGA Cables (M - F) (4) 6 ft. 3.
PANEL LAYOUT Front Panel 6 1 2 3 4 5 7 8 9 10 11 Back Panel 20 12 13 14 15 16 17 18 19 21 22 23 24 25 26 27 28 29 4
PANEL DESCRIPTIONS 1 Power LED This LED indicator glows RED when power is connected properly and sufficient power is being received by the Matrix. 2-5 Selected Input LED Indicators For Outputs 1-4 Each of the four output ports has an associated bank of 4 LED indicators that shows which input source 1-4 is active for that output. The currently selected input will be indicated by an active LED.
CONNECTING AND OPERATING THE 4X4 VGA MATRIX How to Connect the 4x4 VGA Matrix 1. Connect up to 4 VGA video sources to the 4x4 VGA Matrix inputs using the supplied VGA cables. 2. Connect up to 4 Analog Audio sources to the 4x4 VGA Matrix audio inputs using the supplied 3.5mm mini-jack stereo audio cables. 3. Connect up to 4 VGA capable displays to the 4x4 VGA Matrix outputs using user supplied VGA cables. 4.
IR REMOTE DESCRIPTION 1. Remove battery cover from the back of the RMT-16-IR remote (see picture below). 2. Locate the DIP Switches and verify that DIP switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, holding the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT-16-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
4X4 VGA MATRIX REMOTE INSTALLATION How to Resolve IR Code Conflicts In the event that IR commands from other remote controls conflict with the supplied RMT-16IR remote control, changing the remote channel will alleviate this issue. The RMT-16IR remote control has a bank of DIP (Dual Inline Package) switches (see page 7) for configuring the remote channel that both units use to communicate.
USING THE IR REMOTE CONTROL UNIT IR Remote Control Key Mapping Each input and output on the 4x4 VGA Matrix is represented by a button on the IR Remote Control unit. The table below lists the corresponding inputs and outputs.
RS-232 SERIAL CONTROL INTERFACE 54321 12345 9876 6789 Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface Binary Table ASCII Corresponding RMT16-IR Button 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 Binary ASCII 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 0011 0111 0011 1000 9 a b c d e f g Corresponding RMT16-IR Button 9 10 11 12 13 14 15 16 Binary 0011 1001 0110 0001 0110 0010 0110 0011 0110 0100 0110 0101 0110 0110 0110 0111 Additional Features ASCII X or x
RACK MOUNT INSTALLATION Rack mount ears are provided for installation of this unit into a 1U rack mount space. 1. 2. 3. 4. Locate the side screws on the unit. Remove the front 2 screws that are located closest to the front of the unit. Using the removed screws, screw the rack mounting bracket into the unit. Repeat the procedure on the opposite side of the unit.
SPECIFICATIONS Video Amplifier Bandwidth ........................................................................ 350 MHz Input Video Signal ............................................................................... 1.2 Volts p-p Input Sync Signal ......................................................................... 5 Volts p-p (TTL) Horizontal Frequency Range .................................................................. 15-70 KHz Vertical Frequency Range ......................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Rev A4 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com Pb This product uses UL listed power supplies. fax: 818-772-9120 support@gefen.