DESCRIPTION Description Low battery indicator (Green LED) Strobe flasher Red LED OrangeLED Volume control Alarm mode switch Tone control Doorbell tone control Table mounting Speaker FRONT batteries compartment (4 X AA) Wall mounting screw holes Shaker jack Adaptor jack (option) REAR Modular Modular jack PTT line or jack PTT line for a second Amplicall20 connection 2
INSTALLATION Installation (See drawing) 230V AC adaptor UK plug Option: Shaker (ref.:SHAKCL_BLK) Telephone plug Door Bell button Door Bell (Amplicall 1 Amplicall 2\Amplicall 3) 1 - Insert the 4 x AA battery in the compartment . 2 - Connect the RJ11 to RJ11 cable between the Amplicall and phone 3 - Connect one end of the telephone line cord to the unit and the other end to a wall socket. 4 - Connect the adaptor (option). For serving or replacement, you purchase a suitable shaker Model no.
INSTALLATION Electrical connection : The apparatus is designed to operate from a 230V 50Hz supply only. (Classified as «hazardous voltage» according to EN60950 standard). The apparatus does not incorporate an integral power on/off switch. To disconnect the power, either switch off supply at the mains power socket or unplug the AC adaptor. When installing the apparatus, ensure that the mains power socket is readily accessible.
INSTALLATION Setting up Door bell 1. The Door Bell can be take with the people who need the assistance. 2. The door bell can be fixed on the wall or door surround, drill two holes horizontally, 15mm apart, put the supplied anchor into the two holes, hang the door bell on to the two anchors and then instert and tighten screws, and then stick the blank sticker on the two holes. 3. The door be can be stick onto a door, window using the supplied strong adhesive tape.
INSTALLATION Setting UP Indoor unit Wall Mounting 1. Drill two holes horizontally, 96mm apart, and leave the screws protruding from the wall by 5mm. 2. Hang the base on to the two screws and pull the base down to lock it on Table Mounting If you want to mount the unit on the table, only put it into the base cradle, and then place the base cradle on the table.
INSTALLATION Tone Control Switch (3 Positions) Set the tone of the alarm sound. Door Bell Tone Control The three position switch allows you to set a different tone when the door bell rings. Change the Battery of Indoor unit The unit requires 4×AA batteries 1. Open the battery door. 2. Insert four AA batteries into the compartment. 3. Snap the battery compartment door back into place. Note: when the red indicator keep flashes, replace the batteries.
INSTALLATION Note: Do not use a rechargeable battery. Do not put the used battery into the household rubbish, pay attention to battery regulations regarding battery disposal. The Pairing Procedure: 1. Press and hold the Pairing/Test button until the unit makes a beep sound, release the Pairing/Test button, then the 1st LED lights to enter pairing mode. 2.
INSTALLATION (the other 2 LED light), then press and hold the Pairing/Test button until the 1st LED goes off, beeps to confirm. The 1st remote is now un-registered. 3. If user wants to keep the 1st remote but un-register the 2nd or3rd remote, when the 1st LED flashes, press the Pairing/Test button again, the 2nd LED flashes (other 2 LED light) to select which remote to be un-registered. To check whether the unit works normally, you can press the pairing/Test button, the unit would sound alarm and flash.
INSTALLATION Trouble shooting Symptom No incoming call, it rings automatically or rings continuously; the shaker vibrates automatically or continuously; the camera LED flashes automatically. When the power supply works normally, the red low battery LED flashes automatically. When it is connected to the power adaptor or has been installed 4 batteries, however, when there is an incoming call, no rings. Solution 1) Check if the batteries contact well. 2) Check if the power adaptor connects normally.
INSTALLATION When it is connected to the power adaptor or it has been installed 4 batteries, bell rings normally, or camera LED blinks normally, when there is an incoming call, the shaker doesn’t vibrate. If the AmpliCALL20 does not ring when the doorbell is pressed 1) Check if it is connected to the shaker correctly. 2) Check if the shaker socket has been damaged. 3) Check if the alarm mode selection switch position is correct. 1) Check that the red light on the doorbell flashes when it is pressed.
REGULATORY COMPLIANCE - This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. - All applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e. RJ11C) in the package with each piece of approved terminal equipment.
REGULATORY COMPLIANCE company will notify the customer as soon as possible. Also, you will be advised of your rights to file a complaint with the FCC if you believe it is necessary. - The telephone company may make changes in its facilities, equipment, operation or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
REGULATORY COMPLIANCE accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.
GARANTIE From the moment GARANTIE your Geemarc product is purchased, Geemarc guarantee it for the period of one year. During this time, all repairs or replacements (at our option) are free of charge. Should you experience a problem then contact our helpline or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorised Geemarc representative.
best way.When this product is finished with, please do not put it in your domestic waste bin.Please use one of the following disposal options: - Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the product in an appropriate WEEE skip. - Or, hand the old product to the retailer. If you purchase a new one, they should accept it. Thus if you respect these instructions you ensure human health and environmental protection. For product support and help visit our website at www.geemarc.