User's Manual

Place short border walls at the head and foot, between the side walls.
Make sure the foam border walls are connected securely and squarely.
Ensure that the zipper is aligned with the top edge of the foam border walls.
Welcome
GeekSmart bids you welcome to a world of smart home devices, smart mattress.
GeekSmart strives to explore and develop the the smart home industry for the
good of all. combining bridge cutting-edge technologies to develop products fit
and ready for the market.
Please visit our website www.geektechnology.com.
Before Assembling Your Mattress
Decide where to put your new bed
Make sure there’s an electric power source nearby to operate your Control Unit.
Assemble your modular base (optional) or existing bed frame before assembling your
mattress.
Prepare your bed
To achieve the best comfort and support on your GeekSmart mattress, a firm flat
surface, such as the GeekSmart mattress modular base, a solid surface platform bed,
or bunkie board, is recommended. Assemble your modular base or existing bed frame
before assembling your mattress.
Prepare your comfort layer(s)
Comfort layer(s) should be stored at room temperature for at least four hours before
mattress assembly. Carefully open the comfort layer(s) and set aside. They’ll need at
least 30 minutes to fully expand.
Open all the boxes
Carefully check the contents of your mattress boxes. Make sure you have the correct
number of components for the size of bed you purchased.
Spot clean the cover of your GeekSmart mattress with carbonated water. Do not dry
clean the mattress cover or put it in a washing machine. Do not apply stain guard as it
may cause the fabric to turn yellow. GeekSmart mattress is a great leader in the use
of materials designed to inhibit the growth of allergens or microorganisms. Advanced
antimicrobial safeguards are incorporated into every GeekSmart mattress bed. Key
components of the mattress have been treated to protect the bed from contaminants
such as mold, mildew, and bacteria growth. The unique, zip open design of the bed
allows you to easily open, ventilate, or vacuum if you choose.
1. Your GeekSmart bed is intended for in-home, non-commercial use only. Any
unintended use voids the limited warranty.
2. The remote is not a toy and should be used under adult supervision.
3. Do not open the Control Unit system or remote (with the exception of the battery
compartment) The warranty is void if these units are tampered with. The Control
Unit system has no user serviceable parts.
4. Keep the Control Unit and remote away from heat sources such as radiators,
heat registers, etc.
5. Control Unit and remote are not water resistant.
Do not use or store near water — for example, in a wet basement, near an open
window, etc.
封面
封底
Model No.: MS001Q、MT002Q、MT002K
Geek Smart MS001Q、MT002Q、MT002K 智能床垫 说明书
A5 封面250g铜版纸 内页128g铜版纸 双面印 骑马钉
封面封底覆亚膜 彩印
User Manual
GeekSmart Mattress
IMPORTANT：Read the instructions
carefully before operating the appliance
and keep them for future reference.
3
2
4
Safety Introductions
Product Description
11
How To Use
12
Troubleshooting
Clean And Maintenance
Congratulations on your purchase of GeekSmart mattress! GeekSmart mattress，the
perfect combination of AI artificial intelligence, cloud computing and
biosensing control technology and big data, is becoming the latest generation of
human-computer interaction smart mattresses.It is compatible with smartphone to
control the air response technology to adjust the softness of the mattress. A smart
adjustable base（optional）is added for ultimate personalized comfort, biosensor
control technology is also provided to analyze and guide the user’s sleep indica-
tors, allowing users to participate in their own sleep management. We believe the
best sleep of your life begins with the GeekSmart mattress experience, and we
are looking forward to further individualizing your comfort. Our Sleep Professionals
are dedicated to your sleep for life.
Before installing, please scan the QR codes to watch our easy step-by-step
installation video. If you have questions regarding the installation process,
please contact us by mail [e-mail] or by phone
1-844-801-8880.
Smart
Geektechnology Ltd.
120 Route 46 West,
Parsippany, NJ 07054.
Toll Free
1-844-801-8880
[phone]
GeekSmart
APP
Important Safety Instructions
2
What’s Inside
Table Of Contents
Safety Introductions Features
Product Description
3
Never use this fan with any solid-state speed control device.
Doing so is a fire and/or shock hazard.
Warning :
Immediately dispose of packaging as it can pose choking or
other hazards to small children and pets.Please carefully
confirm the consistency between the picture and the real
components that correspond to the model you purchased.
CAUTION:
Model MS-001Q
MT-002Q&
MT-002K
Mattress
Cover
Foam Border
Walls
Comfort
Layer(s)
Sponge Base
Pad
Air Chambers
Air Chambers
Control Unit
Remote
Flex-Base
(Optional)
Mattress FAQs
Q. Will the air escape from the air chamber? What should I do if happen?
A. Usually there are few air leaks. Your mattress will maintain its firmness. You can
set auto-inflate time in the GeekSmart App.
Q. What if my foam comfort layer appears to be too small or irregular?
A. Gently shake the layer as you place it in your mattress and it will recover its full
size overnight.
Q. What if I feel like I’m rolling toward the edge or toward the center of the
mattress?
A. Although rare, these sensations could potentially be experienced if one side of
the mattress is set quite firm and the other side quite soft. Call Customer
Service if this situation occurs to you.
Q. What if I notice a rubber smell from the air chamber(s)?
A. The odor you may smell is non-toxic and will fade over time.To minimize the
smell, unzip the mattress cover and allow the air chamber to air out for a few
hours. Laying a couple of dryer sheets on top of the air chamber will also help
mask any odor by adding a fresh scent.
Q. Does the mattress need long-term charging?
A. It needs to be plugged in for a long time during use, but you can remove the
power supply when you travel or are away from home for a long time.
Q. Will the mattress stop working when power off?
A. After power failure, the machine will maintain the current air pressure
without affecting the normal use.
Q. Can I see the sleep report without WiFi at home?
A. No, sleep reports cannot be generated until the mattress is connected to
the network.
Q. Does the mattress have radiation?
A. The radiation of the machine meets the standard. On the whole, the
radiation is less than that of the mobile phone. In addition, the machine
is far from the human body, and the radiation can be ignored.
Troubleshooting
Troubleshooting
Cleaning Your Mattress
1. Wipe the body with a clean cloth dampened with a mild soap and water solution.
2. Wipe the display screen with a clean, dry, lint-free cloth.
Cleaning Your Remote
1. Always disassemble the base. Bag all hardware so that it is not lost.
2. The mattress can be fully inflated, capped off and packaged in a mattress box
for moving.
3. If you don’t have a mattress box, double-bag the cover to prevent stains.
Deflate and box the air chamber(s) to prevent possible damage.
4. Pack the Control Unit system in a box with packing material.
Transport with minimal exposure to shock and vibration.
5. Tuck the remote, air chamber caps and instructions in the box with the Control
Unit to prevent them from being lost.
Moving Your Bed
Clean And Maintenance
Before Assembling Your Mattress
Control Unit MS-001Q
Preliminary Work:
Open the comfort layer(s) and set aside. Wait for about 30 minutes to fully expand.
Place the main machine at the end of the bed according to the color of the color
ring on the female connector on the main machine's gas pipe, and the color ring of
the male head under the end of the mattress color for docking. When docking, hold
the mattress air pipe in one hand and the host air pipe in the other hand. The
docking is successful when you hear a click.
1. Bed platform
Place on base or on an existing bed platform, making sure openings in the bottom
of the mattress cover are at the head of the bed.
Unzip mattress cover, turn the mattress cover inside out and lay it on the bed platform.
Assembling Your Mattress You Have Finished Assembling
Your Mattress!
4
How To Use How To Use
5
2. Comfort layer(s)
Put the comfort layer in
3. Foam Side Walls
Place air chambers on the comfort layer, make sure the air tube connectors are
face the end of the bed.
Put the Isolation layer between the air chambers and zip air chambers together
Connect the air chambers to the control unit (the color of the band in all
connecters are correspond to each other)and it will automatically inflate for
about 25 minutes until end.
4. Air Chambers
If you purchase MT-002Q&MT-002K(2 comfort layers), place the comfort
isola-tion layer on the memory foam after STEP.3
6
How To Use How To Use
7
5. Sponge Base Pad
Place the Sponge base pad on the air chambers.
Cover the mattress cover over the entire air chambers and comfort layer.
Zip up the cover and finally turn over the mattress.
Place the main machine at the end of the bed according to the color of the color
ring on the female connector on the main machine's gas pipe, and the color ring of
the male head under the end of the mattress color for docking. When docking, hold
the mattress air pipe in one hand and the host air pipe in the other hand. The
docking is successful when you hear a click.
MT-002Q&MT-002K Connect Your Phone
8
How To Use How To Use
9
Remote
10 11 12
How To Use Clean And Maintenance
Connector (end of bed)
Switch
Reset
USB：Heart rate
Heating
Lifting：Left & Head
Lifting：Left & Foot
Lifting：Right & Head
Lifting：Right & Foot
Air Tube(Left - Waist)
Air Tube(Right- Head & Foot)
Air Tube(Right - Waist)
Air Tube(Left - Head & Foot)
Heating
Heart Rate
Flex-base
Air Pump
Bluetooth
Wi-fi
Power
Head
&Foot
Waist Head
&Foot
Waist
Left Right
Connector (head of bed)
Head of bed
Right Left
Green band Red band
Wi-fi
Power
Control Unit
(MS-001Q)
Reset
USB：Heart rate
Heating
Lifting：Left & Head
Lifting：Left & Foot
Lifting：Right & Head
Lifting：Right & Foot
Air Tube(Left Side)
Air Tube(Right Side)
None
Switch
Heating
Heart Rate
Flex-base
Air Pump
Bluetooth
Left Side
Red Band
Right Side
Green Band
Before
Air Tube Connector
Control Unit Connector
The Same Color
After
Control Unit
(MT-002Q&K)