GE Monogram® Installation Instructions Under Cabinet Installation and JX827WN Built-In Kit Microwave Oven Model ZEM200WV
Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference. CAUTION WARNING This appliance must be properly grounded. See “Electrical Supply”, page 6.
Design Information Micr owa v e Oven Model available ZEM200WV White electronic microwave oven Designed for versatility, this Monogram microwave oven adapts to virtually any installation. Accessory kit JX827WN is required for custom in-wall installation. Dimensions and clearances ZEM200WV A - 12 -5/16" (284 mm) B - 23-13/16" (605 mm) C - 11-3/16" (284 mm) (includes feet) Note: When installed, trim kit will require wall space 26-1/8" W x 16-1/4" H for clearance.
Installation Preparation Microwave Oven ZEM200WV In-wall installation Tools and materials required: •3/8" thick plywood (min.) •2" x 4" lumber •Saw •Screws and screwdriver or other hardware for construction of plywood base. Opening for model ZEM200WV must be: • 24 -7/8" ± 1/16" wide. • 15" ± 1/16" high. • With approximately 1-1/4" for oven trim overlap around all edges of opening.
Installation Preparation Micr owav e Oven ZEM200WV With single oven Refer to diagram at right for dimensions when installing ZEM200WV above a Monogram single oven. Note: Trim kit JX827WN is required for installation above a single oven. Within opening of appropriate dimensions: • Install a level base of plywood: – Flush with lower edge of opening. – Entirely covering floor of opening. • 3/8" thick (min.) plywood must be supported by 2" x 4" or 1" x 2" equivalent runners on all four sides.
Installation Preparation Micr owav e Oven Electrical supply Tools and materials required: •3-prong grounded electrical receptacle. •Electrical cable, 2-wire with ground, No. 14 minimum, as required. Monogram microwave ovens require a 120 volt, 60 Hz power supply, protected by a time delay fuse or circuit breaker. ZEM200WV oven is supplied with a power cord 57" long for which a properly grounded 3-prong electrical receptacle is required. • 800 watt* oven ZEM200WV draws 1360 watts, with a 13 amp load.
Installation Preparation Micr owav e Oven ZEM200WV In-wall installation (continued) • When cabinet depth is a critical factor, receptacle should be installed in a side wall at rear of opening: – 14 -5/8" minimum cabinet depth is required. Receptacle installed in side wall. • If receptacle is located behind oven, install receptacle flush with wall to minimize depth: – 16" minimum depth is required. Receptacle installed behind oven, flush with wall.
Installation Micr owav e Oven JX827WN installation Tools and materials required: •Accessory kit JX827WN for in-wall installation of ZEM200WV •2 Phillips head screwdrivers (#1 & #2) •Drill and 3/32" drill bit •Centerpunch or nail •Pencil and ruler JX827WN Parts List 1. Base Pan 2. Rear Duct 3. Side Covers (2) 4. Top Trim 5. Bottom Trim 6. Side Trims 7.
Installation Micr owav e Oven JX827WN installation • Remove the four top plug buttons from the top of the microwave oven cabinet. • Place the microwave oven on the base pan centered left to right. Note: Do not tighten screws until all screws are started. • Install side cover by inserting between oven and base pan. • Start two screws A, through side cover and two screws E, through the cover on top into holes where buttons were removed. • Install other side cover with screws A.
Installation Micr owav e Oven JX827WN installation Screw A • Install rear duct by inserting into bottom flange between the oven and back of base pan. – The rear duct should be as far to the left as possible, between the base pan back flange and the partition on the right side. • Locate and use screws A. • Drive one screw through the rear duct into the partition in the base pan. • Drive one screw into the rear duct side flange near the lamp cover.
Installation Micr owav e Oven Assemble trim kit frame • Assemble top, bottom and side trims with four screws D, as illustrated. Screw D When assembled, top, bottom and side strips must be flush. Note: Bottom trim has a hinge notch and is not interchangable with top trim. Install trim kit frame Caution: Do not overtighten screws; doing so could cause misalignment of top and side strips. Screw C • Use the assembled frame as a template.
Installation Micr owa v e Oven ZEM200WV Under-cabinet mounting Tools and materials required: •Flat-blade screwdriver •Phillips screwdriver •Drill and 1/4" bit •Nail or center punch •Pencil and ruler •Scissors •Hammer •Tape •Line cord holder (supplied) •Two brackets (supplied) 15 13/32" Template 1 3 /4 1 /2 1 /4 Template 2 • Carefully remove the four plastic plug buttons from oven top and the two screws at top rear flange of case. • Remove the two top case screws on the back of oven. Retain screws.
Installation Microwave Oven To drill from inside (continued) – Position remaining piece of Template 2 inside cabinet • With template secured in place, check again that and align hole center line with arrows on Template 1. hole center lines on Template 2 are straight, and – Cut excess paper from center of Template 2 so it will that distance from right to left hole center measures lie flat. distance shown on template.
Installation Micr owav e Oven Finalize under-cabinet installation 13/16" • With template secured in place, check again that hole center lines on Template 2 are straight, and that distance from right to left hole center measures distance shown on template. • Drill mounting holes: – Use of safety glasses is recommended to protect the eyes. – Empty cabinet and remove delicate items from adjacent cabinets. – Use center punch or nail to make an indentation for centering the drill bit.
Notes Microwav e Ovens 15
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center® consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are ® Monogram.