Installation Instructions Automatic Icemaker ZDI15 ZDIS15 Design Guide with Installation Instructions Monogram:
Installation instructions • BEFORE YOU BEGIN: CONTENTS Read these instructions completely and carefuJJy. Design Information Models Available ..............................................................3 Cutout & Product Dimensions ........................................3 • iMPORTANT: Save these instructions for local inspector's use. Optional Accessories ......................................................3 Tools and Materials Required ......................................
Design information MODELS AVAILABLE ZDI15, ZDIS15 Available in black, white and stainless steel, The icemaker may be installed below a countertop or used free-standing. CUTOUT Cutout dimensions shown allow for a full door swing. & PRODUCT DiMENSiONS Additional Clearances: • The installation of a 3/4"thick custom panel will require an additional 1-1/2"wide filler strip on the hinge side. The filler strip will act as a spacer between the icemaker case and an adjacent cabinet.
Installation instructions ADVANCE PLANNING ADVANCE CAUTION: Dueto excessive weight, TWO PEOPLEARE REQUIRED TO MOVE AND iNSTALL THiS ICEMAKER. Failure to do so can result in back or other injury. PLANNING (cont.) Before you begin: 1. If a custom panel is to be installed, follow the instructions shown on pages 9 and 10. -Order ZIP75 (black or white) panel kit. -Order the custom panel from the cabinet manufacturer. -Secure the custom panel onto the icemaker.
Installation instructions POWER SUPPLY REMOVE AND PARTS • Lay the carton on rear face and break open the bottom flap. WARNING: FOR PERSONAL SAFETY,THIS (PleaseAPPLIANCE read carefully). MUST BE PROPERLYGROUNDED. Failure to follow these instructions can result in death, fire, or electrical shock. AVERTISSEMENT PACKAGING • Set the carton upright with all four bottom flaps outward. : • Lift carton up and off icemaker. (S'ilvous lisez avec soin).
InstalJation instructions WATER SUPPLY WATER SUPPLY (cont.) * A cold water supply is required for icemaker operation. The water pressure must be between 30 and 120 p.s.i. • Install optional water filter in the water line near the icemaker. A water filter is recommended in areas where water supply contains sand or particles. Installation instructions are packed with the filter. IMPORTANT: Water SupplyShould Enter FromBack Wall In Shaded Area. * Route GE SmartConnect Kit or 1/4" O.D.
Installation instructions CONNECT WATER SUPPLY REVERSE THE DOOR SWING * The water line should be flushed to clear any foreign material before connecting to the icemaker. IMPORTANT: * Connect the water line to the water supply tube outside of the rear access cover. Tools Required: Water // I • 1/4" and 5/16"wrench • Flat putty knife Line o Disconnect power to the icemaker.
Installation instructions REVERSE THE DOOR SWING (cont.} Reverse the hinges: • Using a flat putty knife, remove the screw hole plugs opposite the door hinges, top and bottom. Set aside. • Remove the two screws holding top hinge. • Turn the hinge upside down, with the hinge pin pointing up. Reinstall the hinge on the opposite side at the bottom of the door. Remove the bottom hinge. Turn the hinge upside down and install on the opposite side atthe top.
Installation instructions for ZIP75WW, ZIP75BB Kit • BEFORE YOU BEGIN: NOTE: If installing a 3/4"trimless custom panel, a 1-1/2"wide filler strip may be required. The filler strip will act as a spacer between the icemaker case and the adjacent cabinet, and will prevent interference with the icemaker door swing when it is installed between frameless or framed cabinetry. The width of the cutout opening must include the width of the filler strip.
Installation instructions for ZIP75WW, ZIP75BB Kit STEP 5 TO THE iCE MACHINE SECURE SIDE TRIM PIECES TO CUSTOM PANEL • Lay the custom panel appearance-side-down on a clean surface. STEP 2 REMOVE HANDLE AND NAMEPLATE • Align top and bottom side trim to the custom panel sides. • Remove the door handle by removing the two top mounting screws. Set screws aside, Discard handle. • Tape the side trim pieces to the back of the custom panel, • The Monogram nameplate is held in place with adhesive.
Notes 11
NOTE:While performing installations described in this book, safety glasses or goggles should be worn. ]l))F o ,_lO?tO_'Yaltt oo [0(:(1[ ,_(_-Uit:( _ i?t 30_tT (/?'('(/, c(l[I l ._00. 444. l,_4 _. NOTE: al and I) vodu(:l ( enel-al Ele(lri(. Sl)e(ifi(aliol_S inll)rov(*nlenl is a continuing Thel-et_n-e, _11(_ stl|)i(..1 malel-ials, lo (hange endeavor al)l)earal_(e wilhoul noli(e. Monogram: Pub.No. 49-60016-4 ] PartNo.