VG2053/VG4053 VCR User’s Guide We bring good things to life.
Introduction Important Information WARNING To reduce the risk of fire or shock hazard, do not expose this VCR to rain or moisture. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.
Introduction Table of Contents Important Information Pause for Stop Action ______________15 Warnings______________________________ i Frame Advance ___________________15 Cautions ______________________________ i Automatic Tracking _______________ 15 Note to Cable TV Installer _______________ i Manual Tracking__________________ 15 Product Registration ____________________ i Recording a Program Types of Recordings ___________________ 16 Hooking Up the VCR Choosing a Hookup ____________________ 2 Ant
Hooking Up the VCR Choosing a Hookup The hookups on pages 3 through 5 are divided into two hookup types: Basic (A) and Advanced (B). The basic hookup shows the backs of TVs that have only an antenna/cable connection. It is the easier of the two and additional accessories may not be needed. The advanced hookup shows the VCR hooked up to a monitor/receiver (TV with audio and video jacks) using a signal splitter. This connection may improve the picture quality as well as convenience of operation.
Hooking Up the VCR Antenna or Cable System Without a Cable Box A. Basic hookup. A Use this hookup for a simple connection which requires fewer accessories. From Antenna or Cable 1. Set the CH3 CH4 switch on back of VCR to either channel 3 or 4. 300/75 Ohm Adapter Back of VCR ANT IN VIDEO AUDIO OR Tune the TV to this channel and use the TV•VCR button to watch the VCR. IN RF OUT OUT CH 4 CH 3 2. Connect as shown. This connection may require additional accessories not provided.
Hooking Up the VCR Cable System With Cable Box to Unscramble All Channels A. Basic hookup. Use this hookup for a simple connection which requires fewer accessories. A From Cable Back of VCR 1. Set the CH3 CH4 switch on back of VCR to either channel 3 or 4. Cable Box Tune the TV to this channel and use the TV•VCR button to watch the VCR. IN RF Coaxial Cable ANT IN VIDEO AUDIO IN OUT RF OUT OUT CH 4 CH 3 2. Connect as shown. This connection may require additional accessories not provided.
Hooking Up the VCR Cable System With Cable Box to Unscramble Only Pay Channels (such as HBO, Showtime, Pay-Per-View, etc.) A. Basic hookup. Use this hookup for a simple connection which requires fewer accessories. A From Cable Back of VCR 1. Set the CH3 CH4 switch on back of VCR to either channel 3 or 4. Cable Box Tune the TV to this channel and use the TV•VCR button to watch the VCR. IN RF Coaxial Cable ANT IN VIDEO AUDIO IN OUT RF OUT OUT CH 3 CH 4 2. Connect as shown.
Hooking Up the VCR Connecting Two VCRs for Copying Tapes Option A hookup. A Use this hookup for a simple connection which requires fewer accessories. Playback VCR From Antenna, Cable or Cable Box 1. Select a hookup from pages 2 through 5 and then modify with this connection. ANT IN VIDEO AUDIO IN RF OUT 2. Set the CH3 CH4 switch on the playback VCR to either channel 3 or 4. OUT CH 4 CH 3 Tune the recording VCR to this channel to receive the signal from the playback VCR.
Setting Up the VCR Startup 1. Check accessories with VCR. Contact your dealer if any items are missing. POWER TV•VCR PREV CH POWER 1 2 3 4 5 6 7 8 9 CHAN 1 2 3 4 5 6 7 8 9 CHAN MENU 2 “AA” Batteries MENU 0 INPUT TV•VCR PREV CH 100 0 MOVE INPUT 100 MOVE PLAY PLAY FF REW FF REW STOP STOP REC PAUSE REC SPEED TRACKING F.ADV SLOW PAUSE SKIP SPEED TRACKING SKIP RF Coaxial Cable (Stock No. 221392) VG2053 Remote (Stock No. 229652) VG4053 Remote (Stock No. 221391) 2.
Setting Up the VCR 5. Place channels in the VCR’s memory. The first time you turn on the VCR or after a power interruption, perform the AUTO CHANNEL SEARCH so that your VCR can memorize the channels available through your signal source—cable or antenna. Also, if you change the signal source, you will need to perform AUTO CHANNEL SEARCH again. A. Press MENU to display the VCR MAIN MENU on the TV screen.
Setting Up the VCR Startup 7. Use TV•VCR button. Skip this step if you used one of the advanced hookups. When using one of the basic hookups, the TV•VCR button lets you switch between the picture coming from the VCR or television channels. Also, this button lets you record a program on the VCR while watching another channel on the TV. A. Press TV•VCR to see the picture from the VCR. The VCR indicator lights in the display panel. B. Press CHAN up or down to change channels on the VCR. C.
Using the Remote Control VCR Function Buttons 100 Lets you select a channel number over 100. CHAN (Channel up or down) Selects the next higher or lower channel in the VCR’s channel memory. POWER POWER 1 1 TV•VCR TV•VCR PREV PREV CH CH 2 2 3 3 POWER TV•VCR PREV CH 1 2 3 CHAN CHAN CHAN 4 4 5 5 6 6 4 5 6 7 7 8 8 9 9 7 8 9 MENU MENU 0 0 INPUT INPUT 100 100 MENU 0 MOVE MOVE INPUT PLAY PLAY SPEED SPEED F.
Using the Remote Control VCR Function Buttons (Continued) PAUSE Pauses action for viewing during playback. Press PAUSE again to resume normal playback. SPEED (Tape Speed) Selects a recording speed (SP, LP, EP). Pauses recording to prevent recording of unwanted scenes. STOP Also, lets you pause a recording, then resume the recording. Stops the VCR’s normal functions such as record, playback, rewind, fast forward, and pause. PLAY Plays a tape. TRACKING up or down POWER Turns the VCR on and off.
Playing a Tape Operating Instructions To Play a Tape 1. Turn on the TV and tune it to channel 3, 4, or the TV’s video input to see the picture from the VCR. HEAD 2. Insert a tape in the VCR. The VCR turns on automatically. The power and VCR indicators light. The tape automatically begins playback if the safety tab on the cassette has been removed. POWER EJECT PRO FECT VIDEO SYSTEM RECORD CHANNEL Safety Tab 3. Press PLAY, if necessary. 4.
Playing a Tape Using the Playback Features Display Clock or Time Counter VCR MAIN MENU You can display the time counter or the clock in the VCR’s display panel. 1 2 3 4 1. Press MENU to display the VCR MAIN MENU. 2. Press 4 to display the SEARCH/COUNTER menu. SET CLOCK TIMER RECORDINGS CHANNELS SEARCH/COUNTER PRESS MENU TO EXIT 3. Press 5 choose CLOCK or COUNTER.
Playing a Tape Using the Playback Features Picture Search You can search for a specific tape location during playback by fast forwarding or rewinding the tape. Sound is turned off during picture search. Picture search works best for tapes recorded in SP or EP speed. Fast Forward Search 1. Press FF to search forward at a faster-than-normal speed. VCR MAIN MENU 1 2 3 4 SET CLOCK TIMER RECORDINGS CHANNELS SEARCH/COUNTER PRESS MENU TO EXIT 2. Press PLAY to return to playback. Rewind Search 1.
Playing a Tape Using the Playback Features Commercial Scan (SKIP Button) This is useful for scanning commercials or short program segments. 1. Press SKIP during playback to advance the tape approximately 60 seconds. Pause for Stop Action This feature stops a tape in action and lets you examine the details of the scene on the screen. Stop actions works best for tapes recorded in SP or EP speed. 1. Press PAUSE on the remote during playback to stop the action. 2.
Recording a Program Types of Recordings Your VCR provides different recording features. The following sections describe these features. Recording Speeds Press SPEED on the remote to select a recording speed (SP, LP, or EP). The speed you select appears on the TV screen. SP (Standard Play) gives the best quality recording. This is why most prerecorded, rental tapes are recorded in SP. Fewer programs can be recorded on the tape.
Recording a Program One Touch Recording One touch recording lets you record up to four hours without using the timer program feature. The VCR turns off automatically at the end of the recording. POWER EJECT RECORD CHANNEL STOP PLAY REW FWD RECORD Operating Instructions 1. Turn on the VCR. 2. Insert a tape with its safety tab in place. 3. Select the channel you want to record. 4. Use SPEED on the remote to select a recording speed. 5.
Recording a Program Recording While You’re Away (Timer Recording) The timer program feature lets you program the VCR to record up to eight different programs within a one year period. Before setting the timer, make sure that: • The clock is set correctly. • A tape with safety tab has been inserted with enough tape to record the programs. Setting a Timer Recording 1. Press MENU on the remote to display the VCR MAIN MENU. 2. Press 2 to display the TIMER RECORDINGS menu. 3.
Recording a Program Recording While You’re Away (Timer Recording) Timer Recording From the VCR’s Line Input The line input refers to the signal coming from the VCR’s AUDIO and VIDEO IN jacks. Recording from the line input is convenient if you have a satellite receiver or similar component attached to these jacks. To timer record from the component connected to the VCR’s line input, press INPUT on the remote to enter AV instead of the channel number on the TV screen during timer programming.
Recording a Program Using Two VCRs for Copying and Editing Tapes Operating Instructions (Refer to hookup on page 6.) Use one VCR as the playback VCR and the other as the recording VCR. Caution: The unauthorized recording of television programs and other materials may infringe the rights of others. 1. Turn on the TV and VCRs. 2. Tune the TV to the VCR viewing channel, either 3, 4, or the TV’s video input. 3.
References Specifications Format: VHS Record/Playback Video: System: Audio: Mono record/playback system Video Signal System: EIA standard: NTSC color Antenna: 75-ohm external VHF/UHF combined antenna terminal Tuner: USA: Type: Auto Programming frequency synthesis Power Requirement: 120V AC, 60 Hz Power Consumption: 17 watts Dimensions: 3.5 inches high (89 mm) 14.2 inches wide (360 mm) 12.3 inches deep (312 mm) Weight: 9 pounds (4.
References Location of Controls Front Panel POWER EJECT RECORD Remote Sensor CHANNEL Up or Down Selects next higher or lower channel in the VCR’s channel memory. PLAY REW FWD Tape Compartment RECORD Start the VCR recording EJECT Press when the VCR is stopped to eject the cassette. Remote Sensor Receives signals from the remote control. Aim the remote at this sensor with no objects between them. FWD (Fast Forward) Fast forwards the tape when the VCR is stopped.
References Location of Controls Back Panel ANT IN VIDEO AUDIO IN RF OUT OUT CH 3 CH 4 CH3 CH4 Switch Selects the channel to which you tune the TV to see the VCR picture if you connect the VCR using one of the basic hookups. VIDEO IN and AUDIO IN Jacks Receives signals from another component like a VCR or camcorder when it is connected to these jacks. Use INPUT on the remote to select. ANT (Antenna) IN Connector Receives a signal from an antenna or cable system when attached.
References Location of Controls Display Panel Channel Number or Line Indicator Status Indicators Cassette In Power Indicator PWR REC VCR SP LEP C VCR Indicator Channel number or Line Input The channel number or line input is displayed. AU lights when you press INPUT and record from the VIDEO IN and AUDIO IN jacks on the back of the VCR. Cassette In Indicator Lights when a tape is in the VCR. Power Indicator Lights when the VCR is turned on.
References Limited Warranty What your warranty covers: • Any defect in material or workmanship. For how long after your purchase: • Ninety days for labor charges. • One year for parts. • The warranty period for rental units begins with the first rental. • Pay any Authorized GE VCR Servicenter the labor charges to repair your VCR. • Pay any Authorized GE VCR Servicenter for the new or, at our option, refurbished replacement parts required to repair your VCR.
References Trouble Checks Sometimes problems can be easily solved by checking a few basic things. Check below before you call for help or take your VCR to an Authorized GE VCR Servicenter. Trouble Here's what to try: No power • Plug VCR into an operating outlet. • Check connections. VCR does not respond to remote • Remove batteries and hold down one or more buttons for several seconds to drain the microprocessor inside the remote and reset it. Re-install the batteries and try remote again.
References Trouble Checks Trouble Here's what to try: Rewind does not operate • Tape already rewound. Timer recording not made or wrong program recorded • Cable box was not turned on at time recording was to begin. • Program entered incorrectly (wrong channel or times). • Power interruption. Reset clock. See page 9. • Check to see if time and date are correct — including AM/PM. • Program exceeded tape’s length or tape was not rewound beforehand.
References Index 100 button ............................................10 Accessories, Included ................................7 Add or Remove Channels from Memory...................................................8 ADD/REMOVE CHANNEL Menu ............8 Antenna Connections .............................2,3 AUDIO IN Jacks...................................3-6,23 AUDIO OUT Jacks ..............................3-6,23 AUTO CHANNEL SEARCH Feature .......8 Back Panel .............................................
Notes 29
For your nearest Authorized Servicenter call toll-free in the U.S.A. 1-800-447-1700 Canadian Consumers – Your toll-free numbers are: English: 1-800-522-0338 French: 1-800-522-0445 If your VCR needs service, please contact your dealer or the nearest Servicenter from the yellow pages. Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in service for your product.
