Brochure

VRF
COMMERCIAL AC DUCTLESS
WATER HEATERS WATER TREATMENT
ROOM AC
SPECIFICATIONS
See page 105 for warranty information.
geappliances.com
133132
See page 105 for warranty information.
132
Simple three-step installation
Zoneline units are de signed for easy in stallation, off or flush with the
floor. When the sleeve is in stalled, the chassis simply slides into place.
Compatibility with exist ing Zoneline wall sleeves and rear grilles
simplifies retrofit installations. A new chassis simply slides into the
already installed wall case; the existing rear grille may be used as is, or
with a minor modifi cation for greater operating efficiency.
The exclusive Quick Connect power supply kit with all models makes it
easy to connect the new unit to power sources already in place.
1. Frame the opening. The RAB77B SMC wall sleeve requires an
opening of 16-1/2" high x 42-3/8" wide, while the RAB81 or RAB81B
wall sleeve requires an opening of 16-1/4" high x 42-1/4" wide.
Position the sleeve, secure it to the studs and then caulk. Complete
instructions are furnished with each unit.
2. Connect the electrical supply. Each Zoneline unit requires a
230/208V or 265V power supply. It is strongly recom mended that
electrical connections be made by a quali fied electrician. All wiring,
including installation of the receptacle, must be in accordance with
local codes.
3. Slide-in chassis. With the wall sleeve, electrical receptacle and exterior
grille in place, the separate chassis simply slides into position. Install the
room side cabinet, and plug into the electrical receptacle. You are now
ready for many years of quiet comfort.
ELECTRICAL WIRING
All wiring, including installation of receptacle, must be made in
accordance with local electrical codes and regulations.
Note: Aluminum wiring may pose special problems—consult
a qualified electrician.
Cooling sizes
All units come in four nominal cooling sizes: 7,000, 9,000, 12,000
and 15,000 BTUH.
Resistance heat
Resistance heat or backup heat output is determined by power
connection kits (15A, 20A or 30A).
Grille options
RAG60 (Stamped Aluminum)
RAG67 Extruded Aluminum Architectural Grille
Molded Exterior Architectural Louvers:
RAG61 (Beige), RAG62 (Maple) and RAG63 (Dark Brown)
Ducted applications
AZ45 and AZ65 Series can be used with ductwork to heat or cool
more than one room. RAK6053 Duct Adapter is applied to top of case
over air discharge. RAK601B Duct Extension is applied to right or left
of adapter. Locally fabricated ductwork may be added to extend to
maximum recommended straight line distance (no turns or bends) of
15 feet. Remote thermostat recommended with ducted applications.
Electrical connection
230/208V units may be plugged into a receptacle. 265V units and
special-application 230/208V units require direct connection. See Architects
and Engineers Design Data Manual for electrical connection information,
including use of sub-base for direct-connected units. Installation must comply
with local electrical codes and regulations.
For the most current updates to features, specifications and
installations or applications, visit our website at www.zoneline.com.
WALL SLEEVE DIMENSIONS
GE ZONELINE® INSTALLATION
Maximum cord extension (in inches)
Room Air/Installation Art
SIDE
VIEW
Inside
Inside
Room
Cabinet
Outside
58
21
Exterior Grille
7-1/16
RAB81 = 16
RAB81B = 16
RAB81 = 20-13/16
RAB81B = 20-13/16
Maximum cord extension (in inches)
Room Air/Installation Art
SIDE
VIEW
Inside
Inside
Room
Cabinet
Outside
58
21
Exterior Grille
7-1/16
RAB81 = 16
RAB81B = 16
RAB81 = 20-13/16
RAB81B = 20-13/16
Maximum cord extension (in inches)
Room Air/Installation Art
SIDE
VIEW
Inside
Inside
Room
Cabinet
Outside
58
21
Exterior Grille
7-1/16
RAB77B = 16-1/4
RAB77B = 20-15/16
GE ZONELINE SPECIFICATIONS —HEATER WATTAGE
Each line cord kit has an integral Leakage Current Detection and Interruption (LCDI) device as required by National Electrical Code (NEC) and Underwriters
Laboratories (UL) for units manufactured after August 1, 2004. Wall case and exterior grille are also required for new construction.
*30 amp heater wattage will be reduced in low fan operation.
265-VOLT PERMANENT (CORD SET) AND DIRECT-CONNECTED UNITS (D)
BTUH SIZE 7,000/9,000 12,000/15,000
Power connection kit
RAK515P &
RAK515D
RAK520P &
RAK520D
RAK530P &
RAK530D
RAK515P &
RAK515D
RAK520P &
RAK520D
RAK530P &
RAK530D
Total watts 2,440 3,450 4,850* 2,460 3,470 4,870*
Heater watts 2,400 3,400 4,800* 2,400 3,400 4,800*
Heater BTUh 8,100 11,600 16,300* 8,100 11,600 16,300*
Total amps 9.1 12.9 18.1 9.3 13.1 18.4
Min. circuit (MCA) 15 20 25 15 20 25
Recommended
protective device
(MOCP)
15 amp
time-delay fuse
or breaker
20 amp
time-delay fuse
or breaker
25 amp
time-delay fuse
or breaker
15 amp
time-delay fuse
or breaker
20 amp
time-delay fuse
or breaker
25 amp
time-delay fuse
or breaker
230/208-VOLT LINE-CORD CONNECTED (P) AND DIRECT-CONNECTED UNITS (D)
BTUH SIZE 7,000/9,000 12,000/15,000
Power connection kit RAK315P & RAK315D
RAK320P &
RAK320D
RAK330P &
RAK330D
RAK315P &
RAK315D
RAK320P &
RAK320D
RAK330P &
RAK330D
Total watts 2,410/1,990 3,420/2,830 4,830/3,990* 2,430/2,020 3,450/2,860 4,860/4,020*
Heater watts 2,400/1,960 3,400/2,780 4,800/3,930* 2,400/1,960 3,400/2,780 4,800/3,930*
Heater BTUh 8,100/6,600 11,600/9,400 16,300/13,400* 8,100/6,600 11,600/9,400 16,300/13,400*
Total amps 10.5/9.6 14.9/13.6 21.0/19.2 10.6/9.7 15.1/13.8 21.2/19.3
Min. circuit (MCA) 15 20 25 15 20 25
Recommended
protective device
(MOCP)
15 amp
time-delay fuse
or breaker
20 amp
time-delay fuse
or breaker
30 amp
time-delay fuse
or breaker
15 amp
time-delay fuse
or breaker
20 amp
time-delay fuse
or breaker
30 amp
time-delay fuse
or breaker
MAXIMUM
CORD REACH
(IN INCHES)
RAB77B wall sleeve
Molded SMC fiberglass-reinforced polyester compound.
A-42-1/8", B-13-7/8", C-16-1/4"
RAB81 and RAB818 wall sleeve
Heavy-gauge galvanized steel, with insulation.
A-42", B-13-3/4", C-16"
Wall opening dimensions
Add 1/4" to A and C dimensions for all cut-out sizes.
RAB81—16-1/4" min. H x 42-1/4" min. W
RAB81B—16-1/4" min. H x 42-1/4" min. W
RAB77B—16-1/2" min. H x 42-3/8" min. W
Extended sleeves also available.
Grille Exterior Grille Exterior
GE ZONELINE SPECIFICATIONS —POWER CONNECTION KITS
AND HEATER WATTAGE
Power connection kits are required on all Zoneline chassis. (See chart on page 000.)
The correct kit for the installation is determined by the voltage and amperage of the electrical circuit and the means of connecting the unit
to the building wiring. If the unit is to be plugged in to a receptacle, a line cord kit would be used; if the unit is to be permanently connected,
a permanent connection kit would be used. Cord set units of 265 volts must be installed in compliance with National Electrical Code.®
POWER CONNECTION KITS
Required on all models. See specification sheet for heater KW and branch circuit ampacity.
LINE CORD CONNECTION KITS
DIRECT CONNECTION KITS
RECEPTACLES/SUB-BASES
TANDEM
230/208V 15 amp
NEMA6-15R
PERPENDICULAR
230/208V 20 amp
NEMA6-20R
LARGE TANDEM
230/208V 30 amp
NEMA6-30R
230/208 Volt Line Cord Connection Kits
RAK315P, RAK320P, RAK330P
265 Volt Permanent Connection Kits
RAK515P, RAK520P, RAK530P.
Short power cord without LCDI for
sub-base use only.
230/208 Volt Direct Connection Kits
RAK315D, RAK320D, RAK330D
265 Volt Direct Connection Kits
RAK515D, RAK520D, RAK530D
265V 20 AMP
NEMA7-20R;
Receptacle used on
265V sub-base
265V 30 AMP
NEMA7-30R;
Receptacle used on
265V sub-base
265V 15 AMP
NEMA7-15R;
Receptacle used on
265V sub-base
RAK204E15C
15 amp sub-base
265 volt
Includes short power cord:
RAK515P
RAK204E20C
20 amp sub-base
265 volt
Includes short power cord:
RAK520P
RAK204E30C
30 amp sub-base
265 volt
Includes short power cord:
RAK530P
RAK204D15C
15 amp sub-base
230/208 volt
Includes power cord:
RAK315SP
RAK204D20C
20 amp sub-base
230/208 volt
Includes power cord:
RAK320SP
RAK204D30C
30 amp sub-base
230/208 volt
Includes power cord:
RAK330SP