Simple DIY Setup A WARNING: RISK OF ELECTRIC SHOCK This prosciutto installation requires handling 120 volt wiring, Install LLL nT Lt your Smart JL CUTE RT ‘your Smart Switch to Ei] the C by GE app
Compatibility Requirements Works with halogen, incandescent and LED bulbs, Neutral wire is not required including C by GE Smart {Wire Is usually white or Grey Bulbs. and Is not required) LED up to 150 walls Rating 120V AC 60Hz Ground wire Is required {Wire is usually green, Incandescent/halogen green with a yellow stripe, up to 450 watts or caper) WI-Fi 802.11 b/g/n @ 2.
Let's Do It aia INCLUDED er " poy minutes of your day CY —rae the switch Voltage Tester Commended; ise Wall Plots CE EL Ungodly Unleaded Grows © 2 Phillips Mounting Screws Wire Labels 2 Philips Face Pict Screws
You Got This! And we're here to help. For in-depth instructional videos and a guided tour through the installation, go to Process MAGENTA BEFORE YOU DO ANYTHING: Step 1 Turn Off The Power! Tum off the power for the switch location at the circuit breaker box. Test existing switch by li switch on/off, ensuring pti not tum on. Now, follow these setup steps for a single gang switch.
IF APPLICABLE Install adapter onto C by GE smart or non-dilemma LED bulbs C by GE smart switches and dimmers are compatible with C by GE smart bulbs. To keep your C by GE bulbs always available and connected, the included bulb adapter should be used to have full control bulbs on the same circuit as the switch.
MAGENTA STEP 2 Remove Your Old Switch 1. Remove the existing wall plate and switch from the wall. 2. Use voltage tester on the black wires to confirm power to the switch is off (recommended). 3. Before disconnecting the wires from the wall, label each with the provided wire labels. A Ground wire Is required. if you don't have this wire, the C by 68 suite Is not compatible, 4. Disconnect wires and remove existing switch.
STEP 3 Connect 3. Connect the ground (green) wire on the switch with the ground (green label} wire from the wall. The Wires cee svimtny raw vis {if applicability. NOTE: Both black wires on the For 3-way switch setup, visit coccyges. switch are interchangeable and can be connected fo dither the load or line wire from the wall. 1. Connect the first line/load (black) wire on the switch fo the line or load (black label} wire from the wall. 2.
MAGENTA Process BLACK PHS CRC, GRAY 11 STEP 4 Fit Wires Into . Wall Box Be Ee according to the image.
STEP 5 Secure The Switch Using a Phillips screwdriver and the screws provided, secure the switch fo the wall until level and flush. Then snap the face plate cover onto the bracket.
STEP 6 Turn The Power Back On After the switch is secured and face plate mounted, tum the power back on at the circuit breaker box. At the switch, LED indicator light or light ring will flash blue indicating the device is wired correctly and the device is in setup mode. Press any button on the switch to enable setup mode If setup mode dimes out. w For Hal, Ge Ts: ov pall 1-344-300-BYRE LED Indicator light or light ring will flash blue until the switch Is added to the C by GE app.
Congratulations! You've completed the Smart Switch installation. Next... Q Download EET Ga Lo both Switch to the C by GE app % E20 REE TY the instructions in the CET Enable Your Voice Assistant Cl Hip Salsa, umn on the bedroom. Google Assistant Lb al Assistant or Go yr dpp, starch for the C by SE cation, follow the seize Hay Google, I'm saving.
Additional Information and Warnings ree Hig TES These limits are lll snide dispel eg rain ee pln the equipment off and on, the user is encourage: gp pi Hip tote Sabine Anthropoid eb tml el following two conditions: This dl a LT gene reprisal Hip Ce iid Information: fe i tid a ad Bo eli ret lL Td eal expos limits, man brig ot ii ended dia pd i 4 Inches normal operation. a Eo sated Le eg oe Hurd for an uncontrolled environment.
ed ll AL CAUTION High Voltage Disconnect power supply le lat lie Se i dl epee we Bale Le ET Type | Enclosure Lr dll nh eT Gyps | action eT Ll Indoor use only.