Installation Guide

ManualsBrandsGE ManualsIndoor FixturesGE ALM1

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC and local codes.

• Use only UL or IEC approved wire for input/output connections.

Minimum size 18 AWG.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC et codes locaux.

• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de

connexion. Taille minimum 18 AWG.

Lighting

Installation Guide

imagination at work

Linear Lighting

(ALM1 Series)

Albeo

LED Luminaire

Prepare Electrical Wiring

Electrical Requirements

• The LED driver must be supplied with 120-277 VAC, 50/60

Hz per product label and connected to an individual properly

grounded branch circuit, protected by a 15 or 20 ampere

circuit breaker.

Grounding Instructions

• The grounding and bonding of the overall system shall be

done in accordance with National Electric Code (NEC) Article

600 and local codes.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (A)/NMB-3(A)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Tools and Components Required:

• ALM1 Series xture

• Mounting hardware (not Included)

• #2 Phillips screwdriver

• Drill

Summary of content (3 pages)

PAGE 1
GE Lighting Installation Guide Albeo LED Luminaire TM Linear Lighting (ALM1 Series) BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes. • Use only UL or IEC approved wire for input/output connections. Minimum size 18 AWG.
PAGE 2
Unit Installation 1 For safety, turn off main power prior to installation. Remove LED plate 2 Before installation, loosen two screws on side of fixture, and open by holding lenses and sliding LED plate away from screws. 3 Remove red wire and blue wire which lead to the power supply from connectors, and remove LED plate from box by rotating LED plate 90° and sliding the plate towards the box until the hinges can be removed.
PAGE 3
8 Reattach red wire and blue wire into connectors, and give wires a firm tug to confirm proper connection. 9 Tuck wires inside and close LED plate. Reinsert screws into LED plate on side of fixture making sure to pull the LED plate firmly against the screw side of box. 10 Restore main power. GE Lighting • 1-888-MY-GE-LED (1-888-69-43-533) • www.gelighting.com The GE brand, logo, and Albeo are trademarks of the General Electric Company. © 2014 GE Lighting , LLC.