Installation guide

ManualsBrandsGE ManualsDishwasherOfficial GE dishwasher

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES1800.432.2737} or visit our website at: www.ge.com

BEFORE YOU BEGIN

Read these instructions completely and

carefullg.

IM PORTANT- Observe all governing codes

and ordinances.

• Note to Installer - Be sure to leave these

instructions for the consumer and local inspector's

use.

• Note to Consumer - Keep these instructions with

your Owner's Manual for future reference.

• Skill Level- Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of

the installer. Product failure due to improper

installation is not covered under the GE

Appliance Warranty. See warranty information.

• Completion Time - I to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT- The dishwasher MUST be

installed to allow for future removal from the

enclosure if service is required.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual for

available custom panel kits.

FOR YOUR SAFETY

Read and observe allCAUTIONS and WARNINGS

shown throughout these instructions.While

performing installationsdescribedinthisbooklet,

glovesand safetgglassesshould be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Summary of content (16 pages)

PAGE 1
Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES1800.432.2737} or visit our website at: www.ge.com IM PORTANT- BEFORE YOU BEGIN Read these instructions carefullg. IM PORTANT- completely Observe all governing and installed enclosure codes and ordinances. • Note to Installer - Be sure to leave these instructions for the consumer and local inspector's The dishwasher MUST be to allow for future removal from the if service is required.
PAGE 2
PARTS SUPPLIED IN INSTALLATION Screw Kit PACKAGE: [] [] [] [] [] [] Two 8-18 x 5/8" Phillips heod wood screws Junction box cover and #10 hex head screw Drain hose (78" long) and hose clamp Cord protector (Power Cord Models Onlg) Conversion leads (Power Cord Models Onlg) Literature, product samples, and/or coupons Phi,,psHeadHexHead _S Wood Screws YOU WILL WX09X70910 [] gour instollotion UL Listed wire nuts (3) [] cord if applicoble Cord Protector (Power Cord Models Onlg) Conversion Leads (P
PAGE 3
Installation Preparation-Enclosure PREPARE DISHWASHER P!_V_Vl=_ ;t _11 _[_ ENCLOSURE To reduce the risk of shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. • The dishwasher must be installed no more than 10 feet from sink for proper drainage. • The dishwasher must be fullg enclosed on the top, sides, and back. • The dishwasher must not support ang part of the enclosure.
PAGE 4
Installation PREPARE DRAIN Preparation-Drain PLUMBING METHOD 1-Air Gap with Waste Tee or Disposer Drain Requirements • Followlocalcodes and ordinances. • Drainhose must notexceed 10 feetinlength, • A highdrainloopor airgap isrequired. See below. Drain Method The type of drain installation depends on the following: • Do local codes or ordinances require an air gap? • Is waste tee less than 18" above the floor? If the answer to either question is YES, on air gap (Method 1) must be used.
PAGE 5
Installation Preparation-Electrical Supply PREPARE ELECTRICAL WIRING P"v._V#l.,'1 :t _II_[_i / FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. iiiJ rT I / I I " Ij [- Receptacle , ,,, I Receptacle Alternate -]" x Locaton _ \ _\ -1-1/2" Dia.Hole (Max.) _1_" I-'_L°cati°fT"l .... - , Cabinet Electrical Requirements • This appliance must be supplied with 120V, 60 Hz.
PAGE 6
Installation Preparation-Hot Water Supply PREPARE HOT WATER SUPPLY Hot Water Line • The line may enter from either side, rear, or floor within the shaded area shown in Figure F. • The line may pass through the same hole as the electrical cable and drain hose, or cut an additional 1-1/2" diameter hole to accommodate the water line. If a power cord with plug is used, the water line must not pass through the power cord hole. Cabinet Face_,- Figure F Water Line Connection • Turn off the water supply.
PAGE 7
Dishwasher Installation STEP 3: REMOVE CAUTION Do not remove the wood until you are ready to STEP 1: PREPARATION Locate the items in the installation package and set them aside for use in the listed steps.
PAGE 8
Dishwasher Installation STEP S: INSTALL POWER STEP 6: INSTALL CORD Skip this step if the dishwasher will be permanently connected to the house electrical system or has a factory installed power cord. In this step you will need the junction box cover and the #10 x 1/2" hex head screw from the screw kit set aside in Step 1. 90 ° ELBOW • Wrap a 90° elbow with thread seal tape. • Thead the 90 ° elbow into the water valve.
PAGE 9
Dishwasher Installation is approximately 78" long. If a longer hose is needed, a 10 foot long hose may be purchased from an authorized GF appliance dealer. The 10 foot long hose is part number GPF10S. Hose Stop Do not use this port if present STEP 9: INSERT DRAIN HOSE AND CORD, IF USED, THROUGH POWER CABINET • Upright the dishwasher and position it in front of the cabinet opening. • Insert the drain hose into the hole previously drilled in the cabinet wall.
PAGE 10
Dishwasher Installation STEP 11: SLIDE DISHWASHER INTO CABINET IM PORTANT STEP 12: POSITION AND LEVEL DISHWASHER - Do not push against the front panel with knees. Damage will occur. IMPORTANT- • Grasp the sides of the front panel and slide the dishwasher into the opening o few inches at o time. Pull the drain hose and power cord, if equipped, through the holes in the adjacent cabinet while sliding the dishwasher into position. proper dish reck operation, wash performance, and door operation.
PAGE 11
Dishwasher Installation STEP 13: FASTEN DISHWASHER UNDERSIDE OF COUNTERTOP TO OR SIDES OF CABINET In this step Uou will need the two 5/8" Phillips head wood screws set aside in Step 1. IM PORTANT - Dishwasher must be centered in cabinet opening. Interference with cabinets or countertop will cause leaks and damage to the door panel and/or control panel. STEP 14: CONNECT WATER SUPPLY Connect the water supply line to the 90° elbow installed in Step 6.
PAGE 12
Dishwasher Installation STEP 15: CONNECT DRAIN LINE Method 1 - Air gap with waste tee or disposer The molded end of the drain hose will fit 5/8" through 1" diameter inlet ports on the air gap, waste tee or disposer. • Determine the size of the inlet port • Cut the drain hose connector on the marked line, if required, to fit the inlet port. __ r_ __ r¢ Cutting Line Waste Tee Installation Disposer Installation Figure × Method 2 - "High drain loop" with waste tee or disposer /.
PAGE 13
Dishwasher Installation STEP 16: CONNECT POWER SUPPLY If a power cord with plug is alreadg proceed to Step 17. installed, If the dishwasher came with a factory-installed power cord and you want to convert it to a permanent connection, refer to the instructions page 16. If house wiring wire, a ground installer. STEP 17: INSTALL If junction Step 18. on When house wiring is aluminum, be sure to use U.L listed anti-oxidant compound and aluminum-to-copper connectors.
PAGE 14
Dishwasher Installation STEP 19: DISHWASHER WET TEST CHECK LIST [] Turn on power supply or if power cord is used, plug it into the wall outlet. [] Latch dishwasher door. [] - Check the electrical connection to the water valve. The red electrical connector should be plugged into the dishwasher water valve. If it is not plugged in, turn off electrical power to the dishwasher. Plug the red connector into the dishwasher water valve and then restore power.
PAGE 15
Dishwasher Installation STEP 20: REPLACE ACCESS PANEL AND TOEKICK In this step gou will need the panels and the two screws set aside in Step 4. There are two tgpes of screws used. The 8-32 x 1/4" screws are used at the top of the access panel and should still be in place. The 10-16 x ]/8" screws are used at the bottom of the access panel and secure both the access panel and toekick. IMPORTANT - Screws are not interchangeable.
PAGE 16
Appendix CONVERTING DISHWASHER EQUIPPED POWER CONNECTION WITH Remove StroinRelief FACTORY CORD TO A PERMANENT This procedure requires the conversion leads set aside in Step 1. • Make sure the power cord for the dishwasher is unplugged from the wall outlet. • Remove screw from junction box cover and remove cover if present. • Disconnect the three power cord conductors from the dishwasher harness. Figure BB • Remove and discard the power cord.